LJLei Jiang
Lei Jiang
*This is an algorithmically generated author record based on publicly available information.
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lei Jiang has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Yongjian Liu
School of Highway, Chang’an University, Xi’an 710064, China
2 shared publications - Amir Fam
Queen’s Univ
1 shared publication - Biao Yan
School of Civil and Transportation Engineering, Guangdong University of Technology, Guangzhou, Guangdong, 510006, China
1 shared publication - Bin Liu
School of Electrical and Electronic Engineering, North China Electric Power University, Baoding, China
1 shared publication - Bo Shao
Department of Oral Implant Center, People’s Hospital of Inner Mongolia Autonomous Region, Hohhot, Inner Mongolia Autonomous Region, PR China
1 shared publication - Guang-Sheng Li
Key Laboratory of Tectonics and Petroleum Resources (China University of Geosciences) Ministry of Education Wuhan China
1 shared publication
Latest Publications
- 1 February 2022
- Published by Elsevier in Structures
- Vol. 36, 589-618
Comparison of strengthening methods for tubular T joint corresponding to each static failure mode
- 1 February 2022
- Published by Elsevier in Structures
- Vol. 36, 589-618
Comparison of strengthening methods for tubular T joint corresponding to each static failure mode
- 1 February 2021
- Published by Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences in Chinese Journal of Liquid Crystals and Displays
- Vol. 36 (2) , 258-264
Remain of photoresist in halftone process based on TFT-LCD technology
- 1 February 2021
- Published by Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences in Chinese Journal of Liquid Crystals and Displays
- Vol. 36 (2) , 258-264
Remain of photoresist in halftone process based on TFT-LCD technology
- 1 March 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 146 (3)
Fatigue Behavior of Integral Built-Up Box Y-Joints between Concrete-Filled Chords with Perfobond Ribs and Hollow Braces
A novel integral built-up box Y-joint welded to rectangular hollow section braces and concrete-filled square hollow section chord stiffened by perfobond ribs was proposed and studied in fatigue. Eight specimens, including one control with a hollow chord, were tested under axial loadings in the brace. Static tests initially were conducted to estimate the hot-spot stresses in the brace–chord weld intersection and at the arc transition point of the gusset plate. Stress concentration factors (SCFs) were compared with those of the hollow chord specimen to assess the influence of concrete fill and perfobond ribs. Fatigue tests then were carried out to failure under cyclic tension force in the brace. Crack initiation locations, crack propagations, failure modes, and the corresponding fatigue data were recorded. Using test results, the design curve for the proposed joint based on hot-spot stress method was established, adopting the least-squares method considering a 95th percentile. The curves of the proposed joint and conventional welded joints without gusset plate were compared for both square and circular braces connected to square chords. Additionally, the curves were compared with those in available design guides. It was shown for the proposed joint that SCFs are significantly lower than for joints with hollow chords and its fatigue strength is much higher than other conventional joints. One design guide curve was shown to overestimate the fatigue strength of the proposed joint; however, curves from other design guides underestimated its fatigue strength.- 1 March 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 146 (3)
Fatigue Behavior of Integral Built-Up Box Y-Joints between Concrete-Filled Chords with Perfobond Ribs and Hollow Braces
A novel integral built-up box Y-joint welded to rectangular hollow section braces and concrete-filled square hollow section chord stiffened by perfobond ribs was proposed and studied in fatigue. Eight specimens, including one control with a hollow chord, were tested under axial loadings in the brace. Static tests initially were conducted to estimate the hot-spot stresses in the brace–chord weld intersection and at the arc transition point of the gusset plate. Stress concentration factors (SCFs) were compared with those of the hollow chord specimen to assess the influence of concrete fill and perfobond ribs. Fatigue tests then were carried out to failure under cyclic tension force in the brace. Crack initiation locations, crack propagations, failure modes, and the corresponding fatigue data were recorded. Using test results, the design curve for the proposed joint based on hot-spot stress method was established, adopting the least-squares method considering a 95th percentile. The curves of the proposed joint and conventional welded joints without gusset plate were compared for both square and circular braces connected to square chords. Additionally, the curves were compared with those in available design guides. It was shown for the proposed joint that SCFs are significantly lower than for joints with hollow chords and its fatigue strength is much higher than other conventional joints. One design guide curve was shown to overestimate the fatigue strength of the proposed joint; however, curves from other design guides underestimated its fatigue strength.