Geonwoo Jeong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Geonwoo Jeong has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Hyunchol Shin
Department of Electronic Convergence Engineering, Kwangwoon University, Seoul 01897, Republic of Korea
3 shared publications - Eun-Seong Kim
Seoul National University
2 shared publications - Hwayoung Jung
Department of Electronic Convergence Engineering, Kwangwoon University, Seoul 01897, Republic of Korea
2 shared publications - Jae-Woo Shin
APR Co., Ltd., Seoul 05551, Republic of Korea
2 shared publications - Jaeeun Jang
Department of Semiconductor Systems Engineering, Kwangwoon University, Seoul 01897, Republic of Korea
2 shared publications - Kyu-Jin Cho
RF Bio Center, Department of Electronic Engineering, Kwangwoon University, Seoul 01897, Republic of Korea
2 shared publications
Latest Publications
- Open Access
- 16 September 2026
- Published by MDPI AG in Electronics
- Vol. 15 (18) , 4205
A 2.4-GHz Bluetooth CMOS RF Transceiver with Improved On-Chip TX/RX Matching and Switching Circuit
This paper presents a fully integrated 2.4-GHz Bluetooth radio frequency (RF) transceiver featuring an area-efficient on-chip RF input/output (RFIO) circuit implemented in a 65-nm CMOS process. The proposed single-ended RFIO, sharing a single antenna pin for both T/R paths, eliminates the need for external transmit/receive (T/R) switches and off-chip impedance matching networks. It achieves a highly compact footprint by minimizing the on-chip LC component count to just four. Furthermore, the reconfigurable RFIO inherently provides a sliding-IF image suppression notch in RX mode and a third-harmonic (HD3) attenuation notch in TX mode. A dedicated calibration circuit is incorporated into the class-D power amplifier to optimally minimize second-harmonic (HD2) distortion. Operating from a 1-V supply, the transceiver consumes 4.77 mW in RX mode and 5.92 mW in TX mode. Experimental measurements demonstrate the RX noise figure of 4.82 dB, with a significantly improved image blocker tolerance of −18.9 dBm. The transmitter delivers −0.5 dBm of fundamental output power while achieving an excellent, state-of-the-art HD2 suppression of −66.6 dBc and HD3 suppression of −43.1 dBc. With its minimal silicon area and robust performance, the proposed transceiver provides a highly attractive solution for low-cost and small form factor wireless Bluetooth applications.
- 16 September 2026
- Published by MDPI AG in Electronics
- Vol. 15 (18) , 4205
Open AccessA 2.4-GHz Bluetooth CMOS RF Transceiver with Improved On-Chip TX/RX Matching and Switching Circuit
This paper presents a fully integrated 2.4-GHz Bluetooth radio frequency (RF) transceiver featuring an area-efficient on-chip RF input/output (RFIO) circuit implemented in a 65-nm CMOS process. The proposed single-ended RFIO, sharing a single antenna pin for both T/R paths, eliminates the need for external transmit/receive (T/R) switches and off-chip impedance matching networks. It achieves a highly compact footprint by minimizing the on-chip LC component count to just four. Furthermore, the reconfigurable RFIO inherently provides a sliding-IF image suppression notch in RX mode and a third-harmonic (HD3) attenuation notch in TX mode. A dedicated calibration circuit is incorporated into the class-D power amplifier to optimally minimize second-harmonic (HD2) distortion. Operating from a 1-V supply, the transceiver consumes 4.77 mW in RX mode and 5.92 mW in TX mode. Experimental measurements demonstrate the RX noise figure of 4.82 dB, with a significantly improved image blocker tolerance of −18.9 dBm. The transmitter delivers −0.5 dBm of fundamental output power while achieving an excellent, state-of-the-art HD2 suppression of −66.6 dBc and HD3 suppression of −43.1 dBc. With its minimal silicon area and robust performance, the proposed transceiver provides a highly attractive solution for low-cost and small form factor wireless Bluetooth applications.
- Open Access
- 14 May 2026
- Published by MDPI AG in Electronics
- Vol. 15 (10) , 2090
Correction: Jeong et al. A 2.4 GHz CMOS Pulse-Mode Transmitter for RF Body-Contouring Device Applications. Electronics 2025, 14, 4826
The authors Kyu-Jin Cho, Jae-Woo Shin, Yun-Seong Eo, Eun-Seong Kim, and Nam-Young Kim were not included as authors in the original publication
- 14 May 2026
- Published by MDPI AG in Electronics
- Vol. 15 (10) , 2090
Open AccessCorrection: Jeong et al. A 2.4 GHz CMOS Pulse-Mode Transmitter for RF Body-Contouring Device Applications. Electronics 2025, 14, 4826
The authors Kyu-Jin Cho, Jae-Woo Shin, Yun-Seong Eo, Eun-Seong Kim, and Nam-Young Kim were not included as authors in the original publication
- Open Access
- 8 December 2025
- Published by MDPI AG in Electronics
- Vol. 14 (24) , 4826
A 2.4 GHz CMOS Pulse-Mode Transmitter for RF Body-Contouring Device Applications
Body-contouring devices deliver controlled thermal energy to treat cellulite, reduce localized fat, and improve skin elasticity. Since the thermal effect is closely related to the delivered RF output power, precise control of the output power is critical for both efficacy and safety. In this study, we propose a 2.4 GHz CMOS pulse-mode transmitter for body-contouring device applications, featuring precise control of the average power delivered to the body. The transmitter comprises a fully integrated phase-locked loop (PLL) synthesizer, pulse modulator (PM), and 10 mW power amplifier (PA). It is fabricated in a 65 nm CMOS with a compact die area of 3.75 mm2. The PA provides four-level continuous-mode output control from −0.3 dBm to 11.1 dBm, and the PM performs programmable PA switching for pulse-mode operation of the PA with a wide range of pulse rates and duty ratios. By combining the continuous-mode output power control and pulse-mode on–off time regulation, the average output power delivered to the skin is finely controlled, managing the delivered power within a safe skin temperature below 65 °C. The PLL loop filter is fully integrated with a wide programmability, improving the form factor and bill of materials for the target devices. Measurement results confirm that the designed transmitter can accurately control both the average output power and pulse profile across the 2.4 GHz ISM band, demonstrating its suitability for compact home-use RF body-contouring devices.
- 8 December 2025
- Published by MDPI AG in Electronics
- Vol. 14 (24) , 4826
Open AccessA 2.4 GHz CMOS Pulse-Mode Transmitter for RF Body-Contouring Device Applications
Body-contouring devices deliver controlled thermal energy to treat cellulite, reduce localized fat, and improve skin elasticity. Since the thermal effect is closely related to the delivered RF output power, precise control of the output power is critical for both efficacy and safety. In this study, we propose a 2.4 GHz CMOS pulse-mode transmitter for body-contouring device applications, featuring precise control of the average power delivered to the body. The transmitter comprises a fully integrated phase-locked loop (PLL) synthesizer, pulse modulator (PM), and 10 mW power amplifier (PA). It is fabricated in a 65 nm CMOS with a compact die area of 3.75 mm2. The PA provides four-level continuous-mode output control from −0.3 dBm to 11.1 dBm, and the PM performs programmable PA switching for pulse-mode operation of the PA with a wide range of pulse rates and duty ratios. By combining the continuous-mode output power control and pulse-mode on–off time regulation, the average output power delivered to the skin is finely controlled, managing the delivered power within a safe skin temperature below 65 °C. The PLL loop filter is fully integrated with a wide programmability, improving the form factor and bill of materials for the target devices. Measurement results confirm that the designed transmitter can accurately control both the average output power and pulse profile across the 2.4 GHz ISM band, demonstrating its suitability for compact home-use RF body-contouring devices.