Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ana Maria Manta has a total of 13 co-authors. Here are the top co-authors by number of shared publications:

  • Andra-Ioana Stănică

    Technological High School “Toma Socolescu”, Gheorghe Grigore Cantacuzino St., 328, 100466, Ploiești, Romania

    1 shared publication
  • Andrei Moldovan

    Department Environmental Engineering and Sustainable Development Entrepreneurship, Technical University of Cluj-Napoca, 400641 Cluj-Napoca, Romania

    1 shared publication
  • Catalina Gabriela Gheorghe

    Chemistry Department, Faculty of Petroleum Refining and Petrochemistry, Petroleum-Gas University of Ploiesti, 39 Bucharest Avenue, 100680 Ploiesti, Romania

    1 shared publication
  • Cristina Maria Dușescu-Vasile

    Department of Petroleum Refining Engineering and Environmental Protection, Petroleum-Gas University of Ploiesti, 39 Bucharest Blvd., 100680 Ploiesti, Romania

    1 shared publication
  • Daniel Bomboș

    S.C. Medacril S.R.L, 8 Carpați Street, Mediaş, Sibiu County, Romania

    1 shared publication
  • Daniela Luminita Movileanu

    Petroleum Refining Engineering and Environmental Protection Department, Faculty of Petroleum Refining and Petrochemistry, Petroleum-Gas University of Ploiesti, 39 Bucharest Avenue, 100680 Ploiesti, Romania

    1 shared publication

Latest Publications

  • Open Access

    Ecotoxicological Monitoring of DSS Microorganisms and Quorum Sensing-Mediated Behavior Control over Metal Corrosion of Al, Zn and Fe

    by Raluca Elena Dragomir, Catalina Gabriela Gheorghe, Cristina Maria DușEscu-Vasile, Ana-Maria Manta, Daniela Luminita Movileanu, Dorin Bombos

    To evaluate the behavior of industrial equipment from a corrosion point of view, it is mandatory to consider both the material that equipment is made from and the working conditions such as temperature, pH, and the existing microorganisms in the working environment. Our studies regarding ecotoxicological monitoring of biological suspensions Diatomee, Saccharomyces, and Spirulina (DSS) are focused on three directions: (1) the evolution of chemical and biological parameters of the reaction environment (pH, conductivity, TDS, DO, OD), the kinetics of DSS microorganisms’ growing curve; (2) the analysis of biofilm forming on the exposed metallic surface and (3) the analysis of corrosion degree (phenomena) of tested metals in five media, by using the corrosion indices: volumetric index, gravimetric index, and penetration index. The viability of microorganisms in the presence of aluminum, zinc, and iron shows the following sequence: AlDiat > FeDiat > ZnDiat > AlSpir > ZnSpir > AlSach > ZnSach > FeSpir > FeSach. The development of biofilms on the surface of metal plates followed the sequence outlined below: AlDiat > FeDiat > ZnDiat > FeSpir > ZnSach > FeSach > AlSach > ZnSpir > AlSpir. Iron exhibits the most favorable performance, displaying a very low Ip value across all tested environments, including salt water. Aluminum demonstrates sensitivity to specific biological environments, with the highest degree of corrosion observed in Spirulina, indicating that not all biological environments confer protection to aluminum. Diatoms and Saccharomyces suspensions exert an inhibitory effect on corrosion. Zinc is the most susceptible metal, experiencing the greatest corrosion in Spirulina, followed by salt water, while biological environments only partially mitigate the corrosion rate.

  • Open Access

    WASTE GRAPE POMACE FOR FOOD PACKAGING

    by Daniel Bomboș, Gabriel Vasilievici, Ana Maria Manta, Loredana Irena Negoiță, Ioan Sarosi, Andrei Moldovan, Filip Miuta, Andra-Ioana Stănică, Stanca Cuc

    The use of waste wine byproducts in packaging manufacture can offer an alternative to plastic pollution. Thus, grape pomace possesses properties that could improve the performance of plastic materials. In this work, the conditioning of grape pomace was studied for the purpose of adding PLA films. Resveratrol was extracted from grape pomace, which was then incorporated into PLA films to enhance their performance. The obtained biopolymers were characterized by determining the mechanical, thermal, and structural properties. The tensile strength of the composites has similar values for the composite with pomace and those with resveratrol, and a similar flexibility of the analyzed samples. The thermal stability of the pomace waste and the composites to which pomace and resveratrol were added was high. DSC tests of PLA-based composites revealed two endothermic peaks at temperatures above 120 °C, probably caused by the melting of amorphous structures. Surface examination indicated a relatively uniform distribution of pomace or resveratrol particles in the polymer matrix, and surface roughness parameters calculated by atomic force microscopy indicated a low to moderate level of roughness, with higher values for pomace-containing films than for resveratrol-based ones, highlighting the more hydrophilic nature of pomace-containing films compared to resveratrol-based ones.