Palvo Leskiv
Research Subjects
Palvo Leskiv has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Igor Tkachenko
Taras Shevchenko National University of Kyiv
1 shared publication Mariia Pientak
1 shared publication- Mykhailo Pylypets
Lutsk Ukraine
1 shared publication - Roman Rohatynskyi
Department of Automobiles Ternopil Ivan Puluj National Technical University Ternopil Ukraine
1 shared publication - Taras Peleshok1 shared publication
Latest Publications
- 4 December 2025
- Published by Central Ukrainian National Technical University in Central Ukrainian Scientific Bulletin. Technical Sciences
- Vol. 2 (12(43))
Features of Forming Screw and Tubular Profiles by Winding on a Cylindrical Mandrel
Roman Rohatynskyi, Professor, Doctor of Science, Professor of the Automobile Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0001-8536- 4599, e-mail: rogatynskyi@gmail.com Mykhailo Pylypets, Professor, Doctor of Science, Professor of the Mechanical Engineering Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000- 0002-4286-9324, e-mail: pulupecmi@gmail.com Igor Tkachenko, Associate Professor, PhD (Candidate of Technical Sciences), Associate Professor of the Mechanical Engineering Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0002-3029-4578, e-mail: tkachenkoigor61@gmail.com Mariia Pientak, Senior Lecturer of the Automobiles Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0001-6758-6593, e-mail: mariaradyk03@ukr.net Taras Peleshok, doctoral student of the Automobile Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0009-0006-2136-8340 , e-mail: madbull@meta.ua Palvo Leskiv, PhD Student, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0009-0003-7564-1785, e-mail: far.better2@gmail.com. The article presents models of winding profiles from strips with different height-to-width ratios of the cross-section using a rotating cylindrical mandrel, along with a justification for the technological design of winding methods for screw and tubular profiles. The stress–strain state during winding is analyzed for plane strain and plane stress conditions under pure bending and bending by transverse force. Differences were established between the bending behavior of wide strips, narrow strips bent on edge, and intermediate profiles on a cylindrical mandrel. A generalized expression was derived to calculate the winding moments for profiles of different cross-sections. It was demonstrated that when bending by a transverse force with a short lever arm, significant friction forces on the mandrel resist the compression of the inner layers of the workpiece, resulting in tensile stresses; thus, bending occurs due to a moment combined with longitudinal forces. Consequently, the total winding moment is higher than under pure bending, leading to greater energy consumption. At the same time, the radial load on the mandrel increases significantly, which negatively affects the durability of the technological equipment. However, bending narrow strips on edge by a transverse force with a short lever arm improves the stability of the winding process and enables broader application of this technological method for the production of twisted profiles. This, in turn, expands the range of wound profiles, in particular screw spirals used in screw conveyors, mixers, and other technological equipment.
- 4 December 2025
- Published by Central Ukrainian National Technical University in Central Ukrainian Scientific Bulletin. Technical Sciences
- Vol. 2 (12(43))
Features of Forming Screw and Tubular Profiles by Winding on a Cylindrical Mandrel
Roman Rohatynskyi, Professor, Doctor of Science, Professor of the Automobile Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0001-8536- 4599, e-mail: rogatynskyi@gmail.com Mykhailo Pylypets, Professor, Doctor of Science, Professor of the Mechanical Engineering Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000- 0002-4286-9324, e-mail: pulupecmi@gmail.com Igor Tkachenko, Associate Professor, PhD (Candidate of Technical Sciences), Associate Professor of the Mechanical Engineering Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0002-3029-4578, e-mail: tkachenkoigor61@gmail.com Mariia Pientak, Senior Lecturer of the Automobiles Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0001-6758-6593, e-mail: mariaradyk03@ukr.net Taras Peleshok, doctoral student of the Automobile Department, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0009-0006-2136-8340 , e-mail: madbull@meta.ua Palvo Leskiv, PhD Student, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0009-0003-7564-1785, e-mail: far.better2@gmail.com. The article presents models of winding profiles from strips with different height-to-width ratios of the cross-section using a rotating cylindrical mandrel, along with a justification for the technological design of winding methods for screw and tubular profiles. The stress–strain state during winding is analyzed for plane strain and plane stress conditions under pure bending and bending by transverse force. Differences were established between the bending behavior of wide strips, narrow strips bent on edge, and intermediate profiles on a cylindrical mandrel. A generalized expression was derived to calculate the winding moments for profiles of different cross-sections. It was demonstrated that when bending by a transverse force with a short lever arm, significant friction forces on the mandrel resist the compression of the inner layers of the workpiece, resulting in tensile stresses; thus, bending occurs due to a moment combined with longitudinal forces. Consequently, the total winding moment is higher than under pure bending, leading to greater energy consumption. At the same time, the radial load on the mandrel increases significantly, which negatively affects the durability of the technological equipment. However, bending narrow strips on edge by a transverse force with a short lever arm improves the stability of the winding process and enables broader application of this technological method for the production of twisted profiles. This, in turn, expands the range of wound profiles, in particular screw spirals used in screw conveyors, mixers, and other technological equipment.