XXXianding Xue

Xianding Xue

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Xianding Xue has a total of 3 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Abrasive water jet cutting of composite materials

    by Xianding Xue

    The demand for high-quality surface integrity and precise kerf geometry in composite machining continues to grow, especially in aerospace and automotive industries, making abrasive water jet cutting a key non-thermal machining technology. However, the process involves complex nonlinear and...

  • Open Access

    Critical Traverse Velocity Threshold for Through-Cut of 3 mm CFRP by Abrasive Waterjet: a Binary Logistic Model Based on Post-Cut Images

    by Xianding Xue

    Abrasive waterjet (AWJ) trimming of thin carbon fibre-reinforced polymer (CFRP) laminates faces the challenge of defining a reliable process window to ensure full penetration without costly metrology. This study establishes, for the first time, a statistically validated through-cut threshold for 3 mm quasi-isotropic T300/epoxy CFRP under standard industrial AWJ parameters (pressure: 200 MPa, abrasive mass flow rate: 120 g/min, standoff distance: 5 mm). Using only post-cut digital caliper measurements and photographic documentation—a low-cost metrology approach—a binary logistic regression model was calibrated from experimental data at three traverse velocities (300, 500, and 700 mm/min, n = 8 replicates each), yielding empirical through-cut probabilities of 1.00, 0.375, and 0.00, respectively. Firth’s bias-reduced penalised likelihood method was employed to address complete separation in the data, providing stable parameter estimates. The model identifies a critical traverse velocity of V₉₅= 292 mm/min (95 % profile-likelihood:276–308 mm/min) guaranteeing 95 % through-cut probability. This quantifies and validates the empirical shop-floor rule of "≤ 300 mm/min". The estimated transition zone width (~200 mm/min) is markedly narrower than that reported for ductile metals, attributable to the low interlaminar fracture toughness of CFRP, which precipitates abrupt, unstable delamination once jet energy flux falls below a critical level. Cross-validation demonstrated a predictive accuracy of 95.8 %. The study provides a robust, accessible framework for process window calibration in small-to-medium enterprises, bridging the gap between empirical practice and statistically controlled manufacturing for thin CFRP components.

  • Open Access

    Integrated Geometric Confinement and Ejection-Driven Drainage Flow for Splash Suppession in High-Speed Abrasive Waterjet Machining

    by Xianding Xue, Oleksandr Salenko

    Abrasive waterjet machining (AWJM) is widely used in aerospace and precision manufacturing due to its cold-cutting nature. However, the residual high-energy jet column penetrating the workpiece frequently impacts the support structure, generating intense splashback that leads to surface contamination and secondary damage. To address this, we propose a composite anti-splash support structure integrating a concave bowl surface with a Venturi-induced negative pressure mechanism. Using VOF multiphase modeling combined with finite element validation, we elucidate the synergistic control mechanism: the curved bowl promotes wall-adherent liquid sliding to reduce radial momentum, while the Venturi throat creates a ~0.15 MPa negative pressure zone that captures droplets into the downstream channel for dissipation. Results demonstrate that compared to conventional supports, the design reduces mixture peak velocity by ~35%, decreases droplet diffusion height by 40%, and curtails radial spread by 30%, effectively constraining contamination areas. Static analysis further confirms the structure maintains high safety margins even under extreme loads. These outcomes not only enhance AWJM processing environments but also provide a validated engineering paradigm for high-speed fluid interaction control. Looking forward, the mechanism resonates with splash suppression needs in photolithography, food packaging, electronic encapsulation, and metal cutting, paving the way for a universal design and evaluation system for splash control in advanced manufacturing.

  • Open Access

    A Review of Abrasive Water Jet Cutting Technology for Composite Materials

    by Xianding Xue, Oleksandr Salenko, Halina Habuzian, Andrii Havrushkevych

    With the growing demand for high-precision and high-reliability machining of composite materials in aerospace, automotive, and electronics industries, abrasive waterjet (AWJ) technology has emerged as a promising method for cutting non-metallic composites due to its cold cutting nature and multi-material adaptability. Compared with pre-2020 studies that mainly focused on parameter trials, recent research has shifted towards modeling of cutting-induced damage, microstructure-level precision control, intelligent optimization, and real-time monitoring, indicating a dual advancement in mechanism understanding and system-level integration. This review summarizes typical damage modes and modeling methods in AWJ cutting of composite materials, compares the applicability of various predictive models and quality indicators, and evaluates representative optimization strategies across different composite systems. Furthermore, it highlights trends in AWJ system intelligence, including acoustic emission monitoring, AI-based modeling, and the integration of digital twin technologies. Future challenges are identified, such as multi-scale modeling of damage–performance coupling, closed-loop process control, and standardized quality assessment frameworks. This review aims to provide structured insights and forward-looking references for advancing AWJ in composite precision manufacturing.