Salokhiddin Yunusov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Salokhiddin Yunusov has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- D. A. Kasimova
2 Andijan State Technical Institute, Andijan, Uzbekistan
1 shared publication - Kenjayev Sirojiddin
1 Department of Materials Science and Mechanical Engineering, Tashkent State Transport University, Tashkent, Uzbekistan
1 shared publication - Murot Turakulov
Tashkent State Transport University, Tashkent, Uzbekistan
1 shared publication - Nodirjon Tursunov
1 Materials Science and Mechanical Engineering, Tashkent State Transport University, Tashkent, Uzbekistan
1 shared publication - Salokhiddin Absattarov
1 Materials Science and Mechanical Engineering, Tashkent State Transport University, Tashkent, Uzbekistan
1 shared publication - Shakhnoza Makhmudova
1 Department of Materials Science and Mechanical Engineering, Tashkent State Transport University, Tashkent, Uzbekistan
1 shared publication
Latest Publications
- Open Access
- 22 December 2025
- Published by JVE International Ltd. in Vibroengineering PROCEDIA
- Vol. 60, 664-669
Research of the stress-strain state and durability of freight wagon trolley springs by the method of finite element modeling in ANSYS
This paper presents a study of the stress-strain state and the prediction of the cyclic durability of a set of trolley springs for freight wagons using the finite element modeling (FEM) method in the ANSYS software package. The aim of the study is to evaluate the influence of materials (steel 55Si2 and 60Si2CrVA) on the performance characteristics of springs under static and dynamic loads corresponding to loaded and empty conditions of the wagon. To achieve this goal, parametric 3D models of springs have been created, finite element models have been developed, and strength and fatigue calculations have been performed. The distributions of equivalent stresses and deformations are analyzed, fatigue durability is predicted, and safety margin coefficients are determined. The results obtained make it possible to evaluate the reliability and durability of springs made of various materials in real-world operating conditions, as well as identify critical stress concentration zones.
- 22 December 2025
- Published by JVE International Ltd. in Vibroengineering PROCEDIA
- Vol. 60, 664-669
Open AccessResearch of the stress-strain state and durability of freight wagon trolley springs by the method of finite element modeling in ANSYS
This paper presents a study of the stress-strain state and the prediction of the cyclic durability of a set of trolley springs for freight wagons using the finite element modeling (FEM) method in the ANSYS software package. The aim of the study is to evaluate the influence of materials (steel 55Si2 and 60Si2CrVA) on the performance characteristics of springs under static and dynamic loads corresponding to loaded and empty conditions of the wagon. To achieve this goal, parametric 3D models of springs have been created, finite element models have been developed, and strength and fatigue calculations have been performed. The distributions of equivalent stresses and deformations are analyzed, fatigue durability is predicted, and safety margin coefficients are determined. The results obtained make it possible to evaluate the reliability and durability of springs made of various materials in real-world operating conditions, as well as identify critical stress concentration zones.
- Open Access
- 22 December 2025
- Published by JVE International Ltd. in Vibroengineering PROCEDIA
- Vol. 60, 839-844
Influence of angular speed of tedder on kinematic parameters of linter machine drive
This article investigates the influence of the tedder’s angular speed on the kinematic and power characteristics of the drive system of the 5LP linter machine. The linter machine is a complex technological unit used to remove residual fibres from the surface of cotton seeds. One of the key factors determining linting efficiency is the interaction between the tedder and the seed roller inside the machine’s working chamber. A detailed kinematic and force analysis is presented, taking into account the resistance forces generated by the seed roller during its movement and processing. Particular attention is given to the development of a calculation model that describes the interaction between the tedder blades and the seed roller. In this model, each blade is treated as a cantilever beam subjected to variable loads resulting from the non-uniform mass and density distribution of the seed material. The analysis demonstrates that variations in the mass and density of the seed roller significantly affect the load transmitted to the drive and the stability of the saw cylinder. The obtained results enable more accurate selection of drive parameters and optimisation of the operating modes of the linter machine. These findings are crucial for improving the productivity and reliability of the equipment, as well as for accounting for both transient and steady-state operating conditions in real industrial environments.
- 22 December 2025
- Published by JVE International Ltd. in Vibroengineering PROCEDIA
- Vol. 60, 839-844
Open AccessInfluence of angular speed of tedder on kinematic parameters of linter machine drive
This article investigates the influence of the tedder’s angular speed on the kinematic and power characteristics of the drive system of the 5LP linter machine. The linter machine is a complex technological unit used to remove residual fibres from the surface of cotton seeds. One of the key factors determining linting efficiency is the interaction between the tedder and the seed roller inside the machine’s working chamber. A detailed kinematic and force analysis is presented, taking into account the resistance forces generated by the seed roller during its movement and processing. Particular attention is given to the development of a calculation model that describes the interaction between the tedder blades and the seed roller. In this model, each blade is treated as a cantilever beam subjected to variable loads resulting from the non-uniform mass and density distribution of the seed material. The analysis demonstrates that variations in the mass and density of the seed roller significantly affect the load transmitted to the drive and the stability of the saw cylinder. The obtained results enable more accurate selection of drive parameters and optimisation of the operating modes of the linter machine. These findings are crucial for improving the productivity and reliability of the equipment, as well as for accounting for both transient and steady-state operating conditions in real industrial environments.
- Open Access
- 22 December 2025
- Published by JVE International Ltd. in Vibroengineering PROCEDIA
- Vol. 60, 818-824
Innovative design of a gear belt transmission for technological machines
The article presents the types of belt transmission designs, as well as the advantages of their use in mechanical engineering. Belt drives create loads as a result of excessive vibrations due to a flexible element (belt). A new design of an innovative toothed belt drive is proposed, which contains two paired driving and driven gear pulleys with different diameters and two belts with teeth covering them, while the gear ratios of each pair of gears are equal to each other. The simulation demonstrates a 25-38 % reduction in velocity fluctuation compared to conventional drives, confirming the effectiveness of the proposed design.
- 22 December 2025
- Published by JVE International Ltd. in Vibroengineering PROCEDIA
- Vol. 60, 818-824
Open AccessInnovative design of a gear belt transmission for technological machines
The article presents the types of belt transmission designs, as well as the advantages of their use in mechanical engineering. Belt drives create loads as a result of excessive vibrations due to a flexible element (belt). A new design of an innovative toothed belt drive is proposed, which contains two paired driving and driven gear pulleys with different diameters and two belts with teeth covering them, while the gear ratios of each pair of gears are equal to each other. The simulation demonstrates a 25-38 % reduction in velocity fluctuation compared to conventional drives, confirming the effectiveness of the proposed design.