Juan Ignacio Canelo-Perez
Juan Ignacio Canelo-Perez has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Javier Carrasco-García
Department of Cartographic and Terrain Engineering, Higher Polytechnic School of Ávila, University of Salamanca, Av. Hornos Caleros, n°50, 05003 Ávila, Spain
2 shared publications - Pedro Carrasco García
Department of Cartographic and Terrain Engineering, Geology, Polytechnic School of Ávila, University of Salamanca, Av. Hornos Caleros, n°50, 05003 Ávila, Spain
2 shared publications - Arturo Zevallos
Department of Cartographic and Terrain Engineering, Higher Polytechnic School of Ávila, University of Salamanca, Av. Hornos Caleros, n°50, 05003 Ávila, Spain
1 shared publication - José Luis Herrero-Pacheco
Department of Cartographic and Terrain Engineering, Geology, Polytechnic School of Ávila, University of Salamanca, Av. Hornos Caleros, n°50, 05003 Ávila, Spain
1 shared publication
Latest Publications
- Open Access
- 7 October 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (19) , 9917
Influence of Earth Tides on Inland Aquifers
Tidal influence is a well-known phenomenon in the hydrogeology of coastal areas, as it is transmitted through aquifers connected to the sea, generating periodic fluctuations in borehole piezometric levels. The analysis of these fluctuations makes it possible to assess subsurface properties and derive characteristic parameters from the transmission of the pressure wave. Tidal influence results from a complex combination of the gravitational attraction exerted by the Sun and the Moon on the oceanic water mass, the tidal distribution conditioned by ocean morphology, and variable meteorological effects that may be highly localised. The combination of these factors generates oscillations ranging in magnitude from metres to centimetres. Under certain circumstances, such as spring tides coinciding with low atmospheric pressure, these oscillations may cause flooding and other undesirable effects in sensitive areas. The effect of earth tides in inland areas disconnected from the sea, sometimes at high elevations, is also well known and has received increasing scientific attention. Tidal oscillations, which are readily apparent in coastal areas, can also be recorded in certain geological materials, producing fluctuations that can be detected using high-precision sensors. These oscillations are caused by the same gravitational attraction responsible for ocean tides; however, in this case, the gravitational forcing acts on the geological formation itself, giving rise to what is known as an Earth tide or astronomical tide. Recent technological advances have facilitated the detection of these phenomena, which were previously difficult to identify. This study analyses the astronomical influence detected in areas clearly isolated from the sea, focusing on small, low-permeability aquifers where direct gravitational forcing of the groundwater mass cannot account for the observed response. Instead, astronomical forcing acts on the rock mass and indirectly affects piezometric levels. The selected experimental site comprises variable lithologies and different degrees of aquifer confinement and includes numerous research boreholes. It therefore provides an optimal setting for analysing the relationship between lithology and astronomical influence and may serve as a basis for future research in different hydrogeological settings.
- 7 October 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (19) , 9917
Open AccessInfluence of Earth Tides on Inland Aquifers
Tidal influence is a well-known phenomenon in the hydrogeology of coastal areas, as it is transmitted through aquifers connected to the sea, generating periodic fluctuations in borehole piezometric levels. The analysis of these fluctuations makes it possible to assess subsurface properties and derive characteristic parameters from the transmission of the pressure wave. Tidal influence results from a complex combination of the gravitational attraction exerted by the Sun and the Moon on the oceanic water mass, the tidal distribution conditioned by ocean morphology, and variable meteorological effects that may be highly localised. The combination of these factors generates oscillations ranging in magnitude from metres to centimetres. Under certain circumstances, such as spring tides coinciding with low atmospheric pressure, these oscillations may cause flooding and other undesirable effects in sensitive areas. The effect of earth tides in inland areas disconnected from the sea, sometimes at high elevations, is also well known and has received increasing scientific attention. Tidal oscillations, which are readily apparent in coastal areas, can also be recorded in certain geological materials, producing fluctuations that can be detected using high-precision sensors. These oscillations are caused by the same gravitational attraction responsible for ocean tides; however, in this case, the gravitational forcing acts on the geological formation itself, giving rise to what is known as an Earth tide or astronomical tide. Recent technological advances have facilitated the detection of these phenomena, which were previously difficult to identify. This study analyses the astronomical influence detected in areas clearly isolated from the sea, focusing on small, low-permeability aquifers where direct gravitational forcing of the groundwater mass cannot account for the observed response. Instead, astronomical forcing acts on the rock mass and indirectly affects piezometric levels. The selected experimental site comprises variable lithologies and different degrees of aquifer confinement and includes numerous research boreholes. It therefore provides an optimal setting for analysing the relationship between lithology and astronomical influence and may serve as a basis for future research in different hydrogeological settings.
- Open Access
- 6 January 2026
- Published by MDPI AG in Preprints.org
Workflow for Buried Pipe Detection and Geotechnical Characterization in Conductive Clay–Marl Environments
Accurate detection of buried utilities and reliable characterization of shallow subsurface conditions are critical requirements in civil and industrial engineering projects, particularly in urban areas developed over conductive clay–marl formations. In such environments, commonly used electromagnetic techniques often fail due to severe signal attenuation, increasing uncertainty during excavation and infrastructure planning. This study presents a high-resolution engineering workflow based on Electrical Resistivity Tomography (ERT) for the simultaneous detection of buried stormwater and sewer pipes and the geotechnical characterization of shallow subsurface materials. The methodology was applied in an industrial area southwest of Pamplona (Navarra, Spain), where Eocene marls and clays dominate the geological setting. Three ERT pro-files, each 23.5 m long, were acquired using a pole–dipole array with a dense electrode spacing of 0.5 m, allowing decimetric-scale resolution and investigation depths of up to 7–8 m. Data were processed and inverted using both smooth (L2-norm) and robust (L1-norm) inversion schemes to evaluate their influence on anomaly detection and stratigraphic imaging. The resulting resistivity models clearly identified elongated conductive and resistive anomalies corresponding to known buried sewer and stormwater pipes, despite the highly conductive background. In addition, the ERT sections revealed lateral and vertical variations within the clay–marl sequence, including sandy and compact detrital facies of direct relevance for foundation design and excavation planning. Borehole data available in the study area corroborated the geophysical interpretation. A complementary Ground Penetrating Radar (GPR) survey confirmed the ineffectiveness of electromagnetic methods under the same conditions due to rapid signal attenuation. Rather than focusing solely on utility detection, the proposed approach frames ERT as a dual-purpose engineering tool capable of providing continuous subsurface infor-mation that bridges the gap between sparse borehole data and construction needs. The workflow presented here is transferable and scalable, offering a practical protocol for urban and industrial projects in conductive soils where conventional techniques are limited.
- 6 January 2026
- Published by MDPI AG in Preprints.org
Open AccessWorkflow for Buried Pipe Detection and Geotechnical Characterization in Conductive Clay–Marl Environments
Accurate detection of buried utilities and reliable characterization of shallow subsurface conditions are critical requirements in civil and industrial engineering projects, particularly in urban areas developed over conductive clay–marl formations. In such environments, commonly used electromagnetic techniques often fail due to severe signal attenuation, increasing uncertainty during excavation and infrastructure planning. This study presents a high-resolution engineering workflow based on Electrical Resistivity Tomography (ERT) for the simultaneous detection of buried stormwater and sewer pipes and the geotechnical characterization of shallow subsurface materials. The methodology was applied in an industrial area southwest of Pamplona (Navarra, Spain), where Eocene marls and clays dominate the geological setting. Three ERT pro-files, each 23.5 m long, were acquired using a pole–dipole array with a dense electrode spacing of 0.5 m, allowing decimetric-scale resolution and investigation depths of up to 7–8 m. Data were processed and inverted using both smooth (L2-norm) and robust (L1-norm) inversion schemes to evaluate their influence on anomaly detection and stratigraphic imaging. The resulting resistivity models clearly identified elongated conductive and resistive anomalies corresponding to known buried sewer and stormwater pipes, despite the highly conductive background. In addition, the ERT sections revealed lateral and vertical variations within the clay–marl sequence, including sandy and compact detrital facies of direct relevance for foundation design and excavation planning. Borehole data available in the study area corroborated the geophysical interpretation. A complementary Ground Penetrating Radar (GPR) survey confirmed the ineffectiveness of electromagnetic methods under the same conditions due to rapid signal attenuation. Rather than focusing solely on utility detection, the proposed approach frames ERT as a dual-purpose engineering tool capable of providing continuous subsurface infor-mation that bridges the gap between sparse borehole data and construction needs. The workflow presented here is transferable and scalable, offering a practical protocol for urban and industrial projects in conductive soils where conventional techniques are limited.