Wenlian Peng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wenlian Peng has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Hanqing Xu
Chemical Defense Institute, Academy of Military Sciences, Beijing 102205, China
2 shared publications - Hao Chen
Chemical Defense Institute, Academy of Military Sciences, Beijing 102205, China
2 shared publications - Jinyan He
Chemical Defense Institute, Academy of Military Sciences, Beijing 102205, China
2 shared publications - Xinggao Zhang
Chemical Defense Institute, Academy of Military Sciences, Beijing 102205, China
2 shared publications - Zhihua Zhuang
Chemical Defense Institute, Academy of Military Sciences, Beijing 102205, China
2 shared publications - Liang Zhou
Research Institute of Chemical Defense, Academy of Military Sciences, Beijing 102205, China
1 shared publication
Latest Publications
- Open Access
Spheroidization Behavior of TiZrNbTa Refractory High-Entropy Alloy Powder During Radio Frequency Plasma Processing
Spherical TiZrNbTa refractory high-entropy alloy powders with uniform composition and good flowability are essential feedstock for powder-based additive manufacturing; however, irregular powders produced by the hydrogenation-dehydrogenation route generally require further shaping treatment. Radio frequency (RF) plasma spheroidization of TiZrNbTa refractory high-entropy alloy powders prepared by hydrogenation-dehydrogenation (HDH) was investigated at a fixed power of 12 kW. Fine (10–40 μm) and coarse (40–70 μm) powders were compared at 5.0 g/min, followed by feed-rate tests (2.5–7.5 g/min) on the coarse fraction. At 5.0 g/min, the spheroidization degrees of the fine and coarse powders were 45.33% and 50.88%, respectively. The fine powder exhibited satellite particles and a broadened particle-size distribution, whereas the coarse powder retained some irregular particles. Decreasing the coarse-powder feed rate from 7.5 to 2.5 g/min increased the spheroidization degree from 45.71% to 94.55%, with median particle size (D50) reaching 56.84 μm and a narrower particle-size distribution. The powders retained predominantly body-centered cubic (BCC) diffraction signatures, while dendritic substructures and local Ta/Zr segregation varied with processing conditions. Testing showed that untreated coarse HDH powder did not flow unaided through a Hall funnel, whereas the 5.0 g/min spheroidized product flowed in 18.7 s/50 g; after spheroidization, its loose bulk density increased from 4.68 to 5.47 g/cm3. These results clarify the effects of particle size and powder feed rate on spheroidization behavior within the investigated conditions.
Open AccessSpheroidization Behavior of TiZrNbTa Refractory High-Entropy Alloy Powder During Radio Frequency Plasma Processing
Spherical TiZrNbTa refractory high-entropy alloy powders with uniform composition and good flowability are essential feedstock for powder-based additive manufacturing; however, irregular powders produced by the hydrogenation-dehydrogenation route generally require further shaping treatment. Radio frequency (RF) plasma spheroidization of TiZrNbTa refractory high-entropy alloy powders prepared by hydrogenation-dehydrogenation (HDH) was investigated at a fixed power of 12 kW. Fine (10–40 μm) and coarse (40–70 μm) powders were compared at 5.0 g/min, followed by feed-rate tests (2.5–7.5 g/min) on the coarse fraction. At 5.0 g/min, the spheroidization degrees of the fine and coarse powders were 45.33% and 50.88%, respectively. The fine powder exhibited satellite particles and a broadened particle-size distribution, whereas the coarse powder retained some irregular particles. Decreasing the coarse-powder feed rate from 7.5 to 2.5 g/min increased the spheroidization degree from 45.71% to 94.55%, with median particle size (D50) reaching 56.84 μm and a narrower particle-size distribution. The powders retained predominantly body-centered cubic (BCC) diffraction signatures, while dendritic substructures and local Ta/Zr segregation varied with processing conditions. Testing showed that untreated coarse HDH powder did not flow unaided through a Hall funnel, whereas the 5.0 g/min spheroidized product flowed in 18.7 s/50 g; after spheroidization, its loose bulk density increased from 4.68 to 5.47 g/cm3. These results clarify the effects of particle size and powder feed rate on spheroidization behavior within the investigated conditions.
- Open Access
Preparation of Highly Active Mg-Al-Li-B Alloys via High-Temperature Sintering
Boron is a promising fuel, but its oxide layer impedes combustion. Alloying boron with other high-energy metals can significantly enhance its combustion performance. In this study, we sintered highly reactive lithium-containing Mg-Al-Li-B alloys using magnesium, aluminum–lithium alloy, and boron powder as raw materials. The effects of sintering temperature and holding time on the microstructure were investigated, and the combustion heat value and oxidation resistance of the alloy were tested. Results indicate that sintering temperature significantly influences phase formation: increasing temperature boosts phase content while reducing metallic phases, with 1100 °C identified as the optimal sintering temperature. Holding time had no discernible impact on the phase composition or combustion heat value of the sintered alloy. Alloying enhances material density, thereby increasing volumetric heat value. Thermal oxidation performance tests demonstrate that Li addition significantly lowers the alloy’s oxidation reaction temperature and activation energy, enhancing its reactivity. This high-heat-value, highly reactive alloy holds significant potential for application in pyrotechnics and propellants.
Open AccessPreparation of Highly Active Mg-Al-Li-B Alloys via High-Temperature Sintering
Boron is a promising fuel, but its oxide layer impedes combustion. Alloying boron with other high-energy metals can significantly enhance its combustion performance. In this study, we sintered highly reactive lithium-containing Mg-Al-Li-B alloys using magnesium, aluminum–lithium alloy, and boron powder as raw materials. The effects of sintering temperature and holding time on the microstructure were investigated, and the combustion heat value and oxidation resistance of the alloy were tested. Results indicate that sintering temperature significantly influences phase formation: increasing temperature boosts phase content while reducing metallic phases, with 1100 °C identified as the optimal sintering temperature. Holding time had no discernible impact on the phase composition or combustion heat value of the sintered alloy. Alloying enhances material density, thereby increasing volumetric heat value. Thermal oxidation performance tests demonstrate that Li addition significantly lowers the alloy’s oxidation reaction temperature and activation energy, enhancing its reactivity. This high-heat-value, highly reactive alloy holds significant potential for application in pyrotechnics and propellants.