Yinshi Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yinshi Lu has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Declan M. Devine
PRISM Research Institute, Technological University of the Shannon, N37 HD68 Athlone, Ireland
2 shared publications - Ke Gong
PRISM Research Institute, Technological University of the Shannon, Athlone N37 HD68, Ireland
2 shared publications Ahmed Erkliğ
Mechanical Engineering Department Gaziantep University Gaziantep Turkiye
1 shared publication- Clement L. Higginbotham
PRISM Research Institute, Technological University of the Shannon, N37 HD68 Athlone, Ireland
1 shared publication - Crevan O'DOnnell
Polymer, Recycling, Industrial, Sustainability and Manufacturing (PRISM) Research Institute, Athlone Campus Technological University of the Shannon: Midlands Midwest Athlone Westmeath Ireland
1 shared publication Daniel P. Fitzpatrick
PRISM Research Institute Technological University of the Shannon Athlone Ireland
1 shared publication
Latest Publications
- 26 August 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (42) , e71403
Effects of Material Extrusion Printing Parameters on the Foaming Behavior and Properties of Foaming Agent Modified Polypropylene: A Taguchi Based Investigation
Foam 3D printing offers a promising route for producing lightweight structures, although the cell morphology and mechanical performance of printed polypropylene remain highly sensitive to processing conditions. This study investigates the effects of printing temperature, printing speed, and nozzle diameter on the foaming behavior and property retention of polypropylene containing a chemical foaming agent using a Taguchi L9 design. Printing temperatures of 220°C–240°C, speeds of 40– 80 mm/s, and nozzle diameters of 0.4–0.8 mm were evaluated through density, hardness, tensile, and flexural testing, scanning electron microscopy, and differential scanning calorimetry. Printing temperature had the greatest influence on density, contributing 34% of the observed variation, and affected hardness and cell morphology. Nozzle diameter was the dominant factor affecting mechanical performance and contributed 59.1% to flexural strength variation. The 0.8 mm nozzle was associated with a more stable cellular structure at high temperatures, while printing speed showed a smaller overall contribution. The preferred conditions identified from the main effect analysis provide practical guidance for selecting printing parameters within the ranges investigated. These findings provide a quantitative basis for balancing lightweight design and mechanical performance.
- 26 August 2026
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (42) , e71403
Effects of Material Extrusion Printing Parameters on the Foaming Behavior and Properties of Foaming Agent Modified Polypropylene: A Taguchi Based Investigation
Foam 3D printing offers a promising route for producing lightweight structures, although the cell morphology and mechanical performance of printed polypropylene remain highly sensitive to processing conditions. This study investigates the effects of printing temperature, printing speed, and nozzle diameter on the foaming behavior and property retention of polypropylene containing a chemical foaming agent using a Taguchi L9 design. Printing temperatures of 220°C–240°C, speeds of 40– 80 mm/s, and nozzle diameters of 0.4–0.8 mm were evaluated through density, hardness, tensile, and flexural testing, scanning electron microscopy, and differential scanning calorimetry. Printing temperature had the greatest influence on density, contributing 34% of the observed variation, and affected hardness and cell morphology. Nozzle diameter was the dominant factor affecting mechanical performance and contributed 59.1% to flexural strength variation. The 0.8 mm nozzle was associated with a more stable cellular structure at high temperatures, while printing speed showed a smaller overall contribution. The preferred conditions identified from the main effect analysis provide practical guidance for selecting printing parameters within the ranges investigated. These findings provide a quantitative basis for balancing lightweight design and mechanical performance.
- Open Access
- 16 August 2026
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (11) , 8244-8262
An Investigation in Poly (Lactic Acid)‐Cellulose Acetate Composites Used for the Controlled Release of Potassium Fertilizers
Biodegradable polymer–based controlled‐release fertilizers (CRFs) offer an environmentally friendly approach to enhancing nutrient use efficiency while minimizing ecological impacts. In this study, poly (lactic acid) (PLA), cellulose acetate (CA), and their blends were investigated as carrier matrices for potassium (K + ). Composites containing 10 wt% potassium sulfate (KS) were produced by melt compounding, followed by comprehensive characterization of their physical, thermal, rheological, mechanical, and K + release performances. The density results confirmed uniform dispersion of KS throughout all formulations. Melt flow index and rheological behaviors revealed that CA content governed melt fluidity, while KS slightly reduced viscosity without compromising processability. Differential scanning calorimetry showed that increasing CA content suppressed PLA crystallinity (from 4% to 2.9% for the blends with no KS loaded and from 5.4% to 3.7% for KS blends) and promoted predominantly amorphous structures, with CA further modulating chain mobility depending on the material composition. The tensile behaviors indicated that PLA contributed strength and stiffness, while CA enhanced ductility; however, limited interfacial compatibility resulted in non‐linear responses, and KS incorporation caused a moderate decline in tensile strength (~17.4%). The K + release studies demonstrated strong dependence on both polymer composition and release environment, where PLA40‐CA60/10% KS exhibited enhanced and tunable K + release, while soil condition produced slower and more complicated release profiles ( n values > 0.5) compared with water condition ( n values < 0.5). Overall, these findings demonstrate that PLA–CA composites effectively mitigate nutrient losses from leaching and percolation, while offering excellent processability and environmental sustainability.
- 16 August 2026
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (11) , 8244-8262
Open AccessAn Investigation in Poly (Lactic Acid)‐Cellulose Acetate Composites Used for the Controlled Release of Potassium Fertilizers
Biodegradable polymer–based controlled‐release fertilizers (CRFs) offer an environmentally friendly approach to enhancing nutrient use efficiency while minimizing ecological impacts. In this study, poly (lactic acid) (PLA), cellulose acetate (CA), and their blends were investigated as carrier matrices for potassium (K + ). Composites containing 10 wt% potassium sulfate (KS) were produced by melt compounding, followed by comprehensive characterization of their physical, thermal, rheological, mechanical, and K + release performances. The density results confirmed uniform dispersion of KS throughout all formulations. Melt flow index and rheological behaviors revealed that CA content governed melt fluidity, while KS slightly reduced viscosity without compromising processability. Differential scanning calorimetry showed that increasing CA content suppressed PLA crystallinity (from 4% to 2.9% for the blends with no KS loaded and from 5.4% to 3.7% for KS blends) and promoted predominantly amorphous structures, with CA further modulating chain mobility depending on the material composition. The tensile behaviors indicated that PLA contributed strength and stiffness, while CA enhanced ductility; however, limited interfacial compatibility resulted in non‐linear responses, and KS incorporation caused a moderate decline in tensile strength (~17.4%). The K + release studies demonstrated strong dependence on both polymer composition and release environment, where PLA40‐CA60/10% KS exhibited enhanced and tunable K + release, while soil condition produced slower and more complicated release profiles ( n values > 0.5) compared with water condition ( n values < 0.5). Overall, these findings demonstrate that PLA–CA composites effectively mitigate nutrient losses from leaching and percolation, while offering excellent processability and environmental sustainability.
- 6 January 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (S1)
Toughening of Intraply Carbon/Kevlar Hybrids With Nanosilica and Nanoclay: Mode‐I and Shear Behavior
This study investigates the influence of nanosilica (NS) and nanoclay (NC) additives on the Mode‐I interlaminar fracture toughness (G IC ) and interlaminar shear strength (ILSS) of intraply woven carbon/Kevlar fiber reinforced epoxy (CKFRE) composites. The toughening mechanisms were observed using a scanning electron microscope and an optical microscope. Results show that both nanoparticle type and concentration critically affect interlaminar performance. At optimum loadings, CKFRE/NC composites exhibited up to 19.1% (2 wt%) and 17.2% (4 wt%) increases in G IC , while CKFRE/NS achieved a 48.4% improvement at 0.5 wt%. ILSS performance followed a similar trend, with enhancements of 21.6% (2 wt% NC) and 25.7% (0.5 wt% NS). These improvements were attributed to synergistic toughening mechanisms, including crack deflection, particle‐induced crack pinning, fiber bridging, and enhanced fiber‐matrix stress transfer. However, higher nanoparticle concentrations led to agglomeration, resin‐rich zones, and a reduction in interfacial bonding efficiency, resulting in deterioration of the properties. The findings highlight optimal concentration ranges of 2–4 wt% NC and 0.5–1 wt% NS, providing valuable design guidelines for next‐generation hybrid composites with improved interlaminar properties for aerospace, defense, and automotive applications.
- 6 January 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (S1)
Toughening of Intraply Carbon/Kevlar Hybrids With Nanosilica and Nanoclay: Mode‐I and Shear Behavior
This study investigates the influence of nanosilica (NS) and nanoclay (NC) additives on the Mode‐I interlaminar fracture toughness (G IC ) and interlaminar shear strength (ILSS) of intraply woven carbon/Kevlar fiber reinforced epoxy (CKFRE) composites. The toughening mechanisms were observed using a scanning electron microscope and an optical microscope. Results show that both nanoparticle type and concentration critically affect interlaminar performance. At optimum loadings, CKFRE/NC composites exhibited up to 19.1% (2 wt%) and 17.2% (4 wt%) increases in G IC , while CKFRE/NS achieved a 48.4% improvement at 0.5 wt%. ILSS performance followed a similar trend, with enhancements of 21.6% (2 wt% NC) and 25.7% (0.5 wt% NS). These improvements were attributed to synergistic toughening mechanisms, including crack deflection, particle‐induced crack pinning, fiber bridging, and enhanced fiber‐matrix stress transfer. However, higher nanoparticle concentrations led to agglomeration, resin‐rich zones, and a reduction in interfacial bonding efficiency, resulting in deterioration of the properties. The findings highlight optimal concentration ranges of 2–4 wt% NC and 0.5–1 wt% NS, providing valuable design guidelines for next‐generation hybrid composites with improved interlaminar properties for aerospace, defense, and automotive applications.