Qingyu Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Qingyu Wang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Wei Xin
National Laboratory of Solid State Microstructures, Nanjing University 1 , Nanjing 210093
2 shared publications - Wenchang Yan
National Laboratory of Solid State Microstructures, Nanjing University 1 , Nanjing 210093
2 shared publications - Yang Yu
National Laboratory of Solid State Microstructures, School of Physics, Nanjing University 1 , Nanjing 210093
2 shared publications - Dong Lan
National Laboratory of Solid State Microstructures, School of Physics, Nanjing University 1 , Nanjing 210093
1 shared publication - Jianwen Xu
National Laboratory of Solid State Microstructures, School of Physics, Nanjing University 1 , Nanjing 210093
1 shared publication - Jie Zhao
School of Physics National Laboratory of Solid State Microstructures Nanjing University 210093 Nanjing China
1 shared publication
Latest Publications
- 31 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (9)
Alternating-bias assisted annealing of micrometer-scale Josephson junctions
Alternating-bias assisted annealing (ABAA) has been effectively utilized to tune the normal-state resistance of sub-micrometer Josephson junctions (JJs). However, how the annealing efficiency is affected by pre-annealing thermal history, oxidation exposure, and junction geometry remains unexplored for micrometer-scale devices. Here, we systematically investigate the ABAA behavior in micrometer-scale JJs to address the growing demands of modern superconducting devices. The dependence of resistance tuning on the pre-annealing heating time, annealing temperature, bias voltage, oxidation exposure, junction linewidth, and aspect ratio is thoroughly characterized. Our results will contribute a predictive framework for the precise resistance control of micrometer-scale JJs, thereby guiding the deterministic fabrication of high-performance superconducting quantum hardware.
- 31 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (9)
Alternating-bias assisted annealing of micrometer-scale Josephson junctions
Alternating-bias assisted annealing (ABAA) has been effectively utilized to tune the normal-state resistance of sub-micrometer Josephson junctions (JJs). However, how the annealing efficiency is affected by pre-annealing thermal history, oxidation exposure, and junction geometry remains unexplored for micrometer-scale devices. Here, we systematically investigate the ABAA behavior in micrometer-scale JJs to address the growing demands of modern superconducting devices. The dependence of resistance tuning on the pre-annealing heating time, annealing temperature, bias voltage, oxidation exposure, junction linewidth, and aspect ratio is thoroughly characterized. Our results will contribute a predictive framework for the precise resistance control of micrometer-scale JJs, thereby guiding the deterministic fabrication of high-performance superconducting quantum hardware.
- Open Access
- 15 January 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (3)
Fabrication of superconducting through-silicon vias with photoresist passivation technique
Superconducting through-silicon vias (TSVs), which enable direct signal transmission between circuit layers and reduce spurious coupling, are essential elements in accomplishing a large-scale quantum circuit. However, the widespread adoption of superconducting TSVs has been hindered by fabrication challenges, such as sidewall roughness and complicated process flow. Here, we propose a technique to fabricate superconducting TSVs. With this technique, a single layer of passivated photoresist (PPR) is treated as a hard mask during the Bosch etching process in order to reach an aspect ratio of 20:1 in a 500μm-thick silicon wafer. Compared with other TSV fabrication techniques, using PPR as a hard mask achieves high etching selectivity (80:1), simplifies fabrication process, and yields smooth sidewalls, while remaining compatible with superconducting quantum circuits. To verify superconducting performance, we performed cryogenic measurements on large-diameter TSVs (500μm) that allow uniform aluminum deposition, yielding a critical temperature (TC) of 1.2 K. This technique supports the development of 3D-integrated architectures for superconducting quantum processors, offering a practical pathway toward high-density circuit architectures.
- 15 January 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (3)
Open AccessFabrication of superconducting through-silicon vias with photoresist passivation technique
Superconducting through-silicon vias (TSVs), which enable direct signal transmission between circuit layers and reduce spurious coupling, are essential elements in accomplishing a large-scale quantum circuit. However, the widespread adoption of superconducting TSVs has been hindered by fabrication challenges, such as sidewall roughness and complicated process flow. Here, we propose a technique to fabricate superconducting TSVs. With this technique, a single layer of passivated photoresist (PPR) is treated as a hard mask during the Bosch etching process in order to reach an aspect ratio of 20:1 in a 500μm-thick silicon wafer. Compared with other TSV fabrication techniques, using PPR as a hard mask achieves high etching selectivity (80:1), simplifies fabrication process, and yields smooth sidewalls, while remaining compatible with superconducting quantum circuits. To verify superconducting performance, we performed cryogenic measurements on large-diameter TSVs (500μm) that allow uniform aluminum deposition, yielding a critical temperature (TC) of 1.2 K. This technique supports the development of 3D-integrated architectures for superconducting quantum processors, offering a practical pathway toward high-density circuit architectures.