Nenad Kranjčević
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nenad Kranjčević has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Joško Deur
University of Zagreb, Faculty of Mechanical Engineering and Naval Architecture, 10002 Zagreb, Croatia
2 shared publications - Matija Hoić
Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, Ivana Lučića 5, 10002 Zagreb, Croatia
2 shared publications - Andreas Tissot
Ford-Werke GmbH, 50769 Cologne, Germany
1 shared publication - Branimir Škugor
Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, 10002 Zagreb, Croatia
1 shared publication - Ivan Ruškan
Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, Ivana Lučića 5, 10002 Zagreb, Croatia
1 shared publication - Krunoslav Haramina
Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, Ivana Lučića 5, 10002 Zagreb, Croatia
1 shared publication
Latest Publications
- Open Access
Design and Experimental Identification of an Active Seat Suspension Mechatronic System
The paper presents the design of an active seat suspension system for a medium-sized passenger vehicle (installation height of 180 mm), which is aimed at enhancing passenger comfort, with an emphasis on autonomous vehicle applications. The system is developed in two design variants based on Scott–Russell and Kempe mechanisms. The former is characterized by high rigidity and low friction, and it serves as a benchmark solution in this research. The latter is distinguished by cost-effectiveness and, thus, targeted for production vehicle applications once it is verified against the benchmark solution. Both designs are developed to satisfy the operational requirements derived from system computer simulations (suspension stroke of ±40 mm, speed of up to 0.5 m/s, and acceleration of up to 1 g), which are based on a half-car vehicle model extended with seat suspension dynamics and controlled by a linear quadratic regulator. The paper also outlines the electrical, measurement, and basic control subsystem of the overall active seat suspension mechatronic system. Finally, it presents experimental identification results to illustrate that the designed system complies with the specified requirements.
Open AccessDesign and Experimental Identification of an Active Seat Suspension Mechatronic System
The paper presents the design of an active seat suspension system for a medium-sized passenger vehicle (installation height of 180 mm), which is aimed at enhancing passenger comfort, with an emphasis on autonomous vehicle applications. The system is developed in two design variants based on Scott–Russell and Kempe mechanisms. The former is characterized by high rigidity and low friction, and it serves as a benchmark solution in this research. The latter is distinguished by cost-effectiveness and, thus, targeted for production vehicle applications once it is verified against the benchmark solution. Both designs are developed to satisfy the operational requirements derived from system computer simulations (suspension stroke of ±40 mm, speed of up to 0.5 m/s, and acceleration of up to 1 g), which are based on a half-car vehicle model extended with seat suspension dynamics and controlled by a linear quadratic regulator. The paper also outlines the electrical, measurement, and basic control subsystem of the overall active seat suspension mechatronic system. Finally, it presents experimental identification results to illustrate that the designed system complies with the specified requirements.
- Open Access
- 23 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (3) , 1177
Stochastic Modelling of Dry-Clutch Coefficient of Friction for a Wide Range of Operating Conditions
This paper presents a stochastic regression model for predicting the coefficient of friction (COF) in automotive dry clutches with organic linings. The influence of temperature, normal load, and slip speed on COF behaviour is investigated based on a large set of clutch wear-characterization data, collected using a custom-designed disc-on-disc tribometer that replicates realistic clutch-engagement cycles. The proposed model calculates both the expected value and standard deviation of the COF. The COF expectation model takes temperature, normal load, and slip speed as inputs, and it has a cubic polynomial form selected through a feature-selection method. The COF standard deviation model is fed by the same three inputs or alternatively the COF expectation input, and it is parameterized using the maximum likelihood method. The overall model is validated on an independent characterization dataset and an additional dataset gained through separate experiments designed to mimic real driving conditions.
- 23 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (3) , 1177
Open AccessStochastic Modelling of Dry-Clutch Coefficient of Friction for a Wide Range of Operating Conditions
This paper presents a stochastic regression model for predicting the coefficient of friction (COF) in automotive dry clutches with organic linings. The influence of temperature, normal load, and slip speed on COF behaviour is investigated based on a large set of clutch wear-characterization data, collected using a custom-designed disc-on-disc tribometer that replicates realistic clutch-engagement cycles. The proposed model calculates both the expected value and standard deviation of the COF. The COF expectation model takes temperature, normal load, and slip speed as inputs, and it has a cubic polynomial form selected through a feature-selection method. The COF standard deviation model is fed by the same three inputs or alternatively the COF expectation input, and it is parameterized using the maximum likelihood method. The overall model is validated on an independent characterization dataset and an additional dataset gained through separate experiments designed to mimic real driving conditions.