M. Ożóg
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Interests
M. Ożóg has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Bogusław Augustyn
Łukasiewicz Research Network – Institute of Non-Ferrous Metals, Light Metals Division, Skawina, Poland
1 shared publication M. Lech-Grega
Łukasiewicz Research Network – Institute of Non-Ferrous Metals, Division in Skawina, 19 Piłsudskiego Str., 32-050 Skawina, Poland
1 shared publication- P. Koprowski
Łukasiewicz Research Network – Institute of Non-Ferrous Metals, Division in Skawina, 19 Piłsudskiego Str., 32-050 Skawina, Poland
1 shared publication - Piotr Uliasz
NPA Skawina LLC, NPA Boryszew Group Company, Piłsudskiego 23, 32-050 Skawina, Poland
1 shared publication - Sonia Boczkal
Łukasiewicz Research Network, Institute of Non-Ferrous Metals, 19 Piłsudskiego Street, 32-050 Skawina, Poland
1 shared publication - Ł. Wodzinski
Boryszew S.A., Modern Aluminium Products, 23 Piłsudskiego Str., 32-050 Skawina, Poland
1 shared publication
Latest Publications
- 28 February 2022
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 67 (1) , 303-309
The Effect of 0.2% Addition of Mg, Co and Ce on Microstructure and Mechanical Properties of 1xxx Series Aluminium Alloy Castings Designed for Overhead Transmission Lines
The effect of 0.2% addition of Mg, Co and Ce to 99.9% cast aluminium was studied by evaluation of changes in microstructure and mechanical properties. The microstructure was analyzed by scanning electron microscopy and transmission electron microscopy. The Al99.9 alloy contained only Al-Fe-Si phase particles. Similar Al-Fe-Si particles were observed in alloy with 0.2% Mg addition, because this amount of magnesium was fully dissolved in the solid solution. The addition of cobalt resulted in the formation of Al9.02Co1.51Fe0.47 phase particles assuming the shape of eutectic plates. The electron backscattered diffraction map made for the alloy with 0.2% Co addition showed numerous twin boundaries with distances between them in the range from 10 to 100 µm. The addition of cerium was located in the grain boundary area. Cerium also gave rise to the formation of two types of particles, i.e. Al4Ce and Al-Ce-Fe-Si. The Al-Ce-Fe-Si phase is a nucleation site for the Al4Ce phase, which forms eutectic plates. The results showed that the introduction of additives increases the mechanical properties of the cast materials. The 99.9% cast aluminium has a hardness of 16.9 HB. The addition of 0.2% by weight of Mg, Co, Ce increases this hardness to 21.8 HB, 22.6 HB and 19.1 HB, respectively.
- 28 February 2022
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 67 (1) , 303-309
The Effect of 0.2% Addition of Mg, Co and Ce on Microstructure and Mechanical Properties of 1xxx Series Aluminium Alloy Castings Designed for Overhead Transmission Lines
The effect of 0.2% addition of Mg, Co and Ce to 99.9% cast aluminium was studied by evaluation of changes in microstructure and mechanical properties. The microstructure was analyzed by scanning electron microscopy and transmission electron microscopy. The Al99.9 alloy contained only Al-Fe-Si phase particles. Similar Al-Fe-Si particles were observed in alloy with 0.2% Mg addition, because this amount of magnesium was fully dissolved in the solid solution. The addition of cobalt resulted in the formation of Al9.02Co1.51Fe0.47 phase particles assuming the shape of eutectic plates. The electron backscattered diffraction map made for the alloy with 0.2% Co addition showed numerous twin boundaries with distances between them in the range from 10 to 100 µm. The addition of cerium was located in the grain boundary area. Cerium also gave rise to the formation of two types of particles, i.e. Al4Ce and Al-Ce-Fe-Si. The Al-Ce-Fe-Si phase is a nucleation site for the Al4Ce phase, which forms eutectic plates. The results showed that the introduction of additives increases the mechanical properties of the cast materials. The 99.9% cast aluminium has a hardness of 16.9 HB. The addition of 0.2% by weight of Mg, Co, Ce increases this hardness to 21.8 HB, 22.6 HB and 19.1 HB, respectively.