JLJiahe Liu

Jiahe Liu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jiahe Liu has a total of 5 co-authors. Here are the top co-authors by number of shared publications:

  • Yao Hong

    Department of Engineering Mechanics, Key Laboratory of Hydrodynamics (MOE), Shanghai Jiao Tong University , Shanghai

    3 shared publications
  • Zhaoxin Gong

    Department of Engineering Mechanics, Key Laboratory of Hydrodynamics (MOE), Shanghai Jiao Tong University , Shanghai

    3 shared publications
  • Jianyong He

    Department of Engineering Mechanics, Key Laboratory of Hydrodynamics (MOE), Shanghai Jiao Tong University , Shanghai 200240

    2 shared publications
  • Gangpeng Wang

    Department of Engineering Mechanics, Key Laboratory of Hydrodynamics (MOE), Shanghai Jiao Tong University , Shanghai

    1 shared publication
  • Jianyong He

    Department of Engineering Mechanics, Key Laboratory of Hydrodynamics (MOE), Shanghai Jiao Tong University , Shanghai

    1 shared publication

Latest Publications

  • Mechanism of load reduction in a bottom-cavity wedge during free-fall water entry

    by Gangpeng Wang, Jiahe Liu, Jianyong He, Yao Hong, Zhaoxin Gong

    This study investigates the air–water flow dynamics and impact load characteristics of a wedge during free fall water entry in calm conditions using a combination of experimental and numerical methods. The load reduction mechanism and hydrodynamic regulation effects of a bottom cavity structure are clarified. Results show that the cavity reduces the peak impact load by decreasing the effective wetted area, physically disrupting the continuous bottom high-pressure region, and redirecting a portion of the incoming flow into the cavity to form an axial jet. Dimensional analysis reveals the influence of the Froude number (Fr): as Fr increases, the effect of gravity on the flow gradually diminishes, and the flow becomes increasingly dominated by inertial effects. Consequently, the peak drag coefficient decreases monotonically and eventually stabilizes, and the flow exhibits self-similar behavior. The cavity demonstrates a stable load reduction capability, with the load reduction ratio ranging from 14.63% to 18.18%. By incorporating three-dimensional effects, a quantitative relationship between the load reduction ratio and a correction coefficient is established. Furthermore, a predictive model for the load reduction ratio is developed based on the morphology of the high-pressure region, using a relative eccentricity parameter to quantify its asymmetry. These findings provide a theoretical foundation for predicting hydrodynamic loads and designing passive load reduction strategies for wedges and related engineering structures.

  • Research on slamming load-reduction method for seaplane water landing based on pressure-relievable cavities

    by Jiahe Liu, Jianyong He, Yao Hong, Zhaoxin Gong

    This study proposes a pressure-relievable cavity method to mitigate slamming loads during seaplane water landings. The method reduces impact loads by decreasing the forebody wetted area during initial water entry. Validated through prototype-scale numerical simulations and 1:40 scale combined numerical-experimental tests for zero-pitch-angle landing, the approach achieves over 30% load reduction in calm water and over 20% load reduction during landings near the wave crest. Under the following wave conditions, slamming loads are classified into single-peak, primary–secondary-peak, and multi-peak patterns. The effectiveness of full- and single-cavity activation is evaluated across these regimes. While cavity-induced free-surface disturbances may generate new high-pressure zones, potentially diminishing or reversing load reduction, optimal performance is achieved by tailoring cavity activation to the slamming pattern. Full activation is most effective for single-peak and primary–secondary-peak cases, whereas selective activation disrupts high-pressure regions. For the multi-peak case, opening a forward cavity reduces loads by disrupting the forebody high-pressure region and avoiding the aftbody slamming amplification from rear- or full-cavity activation. This work provides a design framework for effective slamming mitigation and enhanced safety in emergency seaplane operations.


  • Investigation of slamming loads during seaplane water landing under regular wave conditions

    by Jiahe Liu, Jianyong He, Yao Hong, Zhaoxin Gong

    The safety of seaplane operations during water landings is critically influenced by wave-induced slamming loads, particularly in emergency scenarios. This study employs a validated numerical model incorporating heave and pitch motions to investigate the effects of wave phase angle, initial water contact point, and pitch angle on slamming dynamics. Peak vertical overloads are most severe during wave crest and trough landings due to rapid expansion of the hull–wave contact area. A water particle velocity factor, accounting for the relative motion between the seaplane and waves, is introduced to establish a linear correlation between peak impact loads and wetted area for nearly all phase angles. The results demonstrate that forward displacement of the initial water contact point reduces peak loads, while variations in pitch angle exhibit non-monotonic behavior. Maximum loading occurs at 0° pitch due to full hull engagement, while a 6° pitch induces a localized near-parallel contact of the aftbody with the wave surface, resulting in a rebound in the peak load. The results provide support for predicting transient loads and optimizing structural designs to withstand slamming loads.