Josef Eizenhammer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Josef Eizenhammer has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Andreas Jossen
Technical University of Munich
2 shared publications - Can Korkmaz1 shared publication
- Christoph Macho
Technical University of Munich (TUM)
1 shared publication - Franz Roehrer
Technical University of Munich (TUM), TUM School of Engineering and Design; Department of Energy and Process Engineering, Chair of Electrical Energy Storage Technology (EES), Arcisstr. 21, 80333 Munich, Germany
1 shared publication - Johannes Natterer
Technical University of Munich (TUM), TUM School of Engineering and Design; Department of Energy and Process Engineering, Chair of Electrical Energy Storage Technology (EES), Arcisstr. 21, 80333 Munich, Germany
1 shared publication - Marcel Rogge
Technical University of Munich, School of Engineering and Design, Department of Energy and Process Engineering, Chair of Electrical Energy Storage Technology 80333 Munich, Germany
1 shared publication
Latest Publications
- Open Access
- 12 October 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (19) , 190515
Determining the Particle Size Distribution of an LiFePO 4 Electrode for Full-Cell Many-Particle Modeling
Lithium iron phosphate (LFP) electrodes exhibit history-dependent electrode behavior. It originates from particle-level phase-change behavior, which strongly depends on the particle size distribution (PSD). Current modeling approaches for LFP either assume a uniform particle size, a predefined PSD, or determine the PSD through resource-intensive imaging techniques. Extending these approaches, this work introduces a thermodynamically grounded methodology for determining the PSD from low-current half-cell experiments. For this purpose, a many-particle model (MPM) based on regular solution theory using a particle size-dependent Gibbs energy is introduced. The MPM serves as the basis for an optimization procedure. This procedure determines a PSD that reproduces the measured half-cell potential when used as a model input. To demonstrate the applicability of the determined PSD, the developed MPM is embedded in a physicochemical equivalent circuit full-cell model. Building on an existing parameter set for a Doyle–Fuller–Newman model, the model reproduces full-cell voltage profiles up to C/2 with RMSE values below 8 mV during charge and 14 mV during discharge when compared to experimental data. The presented workflow provides a practical route from low-current half-cell measurements to particle-resolved full-cell modeling, enabling more accurate and experimentally accessible simulations of LFP-based batteries.
- 12 October 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (19) , 190515
Open AccessDetermining the Particle Size Distribution of an LiFePO 4 Electrode for Full-Cell Many-Particle Modeling
Lithium iron phosphate (LFP) electrodes exhibit history-dependent electrode behavior. It originates from particle-level phase-change behavior, which strongly depends on the particle size distribution (PSD). Current modeling approaches for LFP either assume a uniform particle size, a predefined PSD, or determine the PSD through resource-intensive imaging techniques. Extending these approaches, this work introduces a thermodynamically grounded methodology for determining the PSD from low-current half-cell experiments. For this purpose, a many-particle model (MPM) based on regular solution theory using a particle size-dependent Gibbs energy is introduced. The MPM serves as the basis for an optimization procedure. This procedure determines a PSD that reproduces the measured half-cell potential when used as a model input. To demonstrate the applicability of the determined PSD, the developed MPM is embedded in a physicochemical equivalent circuit full-cell model. Building on an existing parameter set for a Doyle–Fuller–Newman model, the model reproduces full-cell voltage profiles up to C/2 with RMSE values below 8 mV during charge and 14 mV during discharge when compared to experimental data. The presented workflow provides a practical route from low-current half-cell measurements to particle-resolved full-cell modeling, enabling more accurate and experimentally accessible simulations of LFP-based batteries.
- Open Access
- 3 February 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 670
How to determine the degradation modes of lithium-ion batteries with silicon–graphite blend electrodes
- 3 February 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 670
Open AccessHow to determine the degradation modes of lithium-ion batteries with silicon–graphite blend electrodes