Pēteris Patriks Jefimovs
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pēteris Patriks Jefimovs has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Aina Bernava
Faculty of Natural Sciences and Technologies, Riga Technical University, 3 Paula Valdena Street, LV-1048 Riga, Latvia
2 shared publications - Ivan Bochkov
Institute of Chemistry and Chemical Technology, Faculty of Natural Sciences and Technology, Riga Technical University, 3 Paula Valdena Street, LV-1048 Riga, Latvia
2 shared publications - Janis Zicans
Institute of Chemistry and Chemical Technology Faculty of Natural Sciences and Technology Riga Technical University Riga Latvia
2 shared publications - Juris Bitenieks
Institute of Chemistry and Chemical Technology, Faculty of Natural Sciences and Technology, Riga Technical University, 3 Paula Valdena Street, LV-1048 Riga, Latvia
2 shared publications - Karina Balina
Centre of Science and Engineering, 14 Lielā Street, RTU Liepaja, LV-3401 Liepaja, Latvia
2 shared publications - Reina Rozentale
Centre of Science and Engineering, 14 Lielā Street, RTU Liepaja, LV-3401 Liepaja, Latvia
2 shared publications
Latest Publications
- Open Access
Use of Waste Red Seaweed Furcellaran for Development of Green Thermoplastically Processable Bioplastics
Bioplastics are in focus for the development of sustainable materials due to the depletion of fossil resources, generation of solid waste and global climate change. Considering this, the current research is devoted to the valorization of beachcast red seaweed F. lumbricalis for the development of thermoplastically processable bioplastics. The composites have been developed from beachcast red seaweed-derived furcellaran (FUR) and potato-derived thermoplastic starch (TPS) by using an ultrasound-assisted technique. Three different FUR concentrations (10, 30 and 50 wt.%) in relation to potato starch were examined for their thermoplastic processability. Fourier infrared spectroscopy (FTIR) was used to reveal the structural changes in the developed TPS/FUR composites depending on FUR content as well as thermal pre-treatment. Thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and tensile mechanical tests were performed to assess the performance of the developed TPS/FUR composites. It was demonstrated that the ultrasound-assisted manufacturing route allowed TPS/FUR composites with an improved spectrum of properties to be obtained. The highest mechanical stress at break (almost three times higher than for neat TPS) was observed for the TPS + 50 wt.% FUR composite, which also possessed decreased deformability (only ca 10%), reduced thermal resistance at processing temperatures (150 °C) and high shear sensitivity. Thus, the TPS + 30 wt.% FUR and especially the TPS + 10 wt.% FUR composites were recognized as more suitable for thermoplastic processing and the development of TPS-based composites with improved exploitation properties.
Open AccessUse of Waste Red Seaweed Furcellaran for Development of Green Thermoplastically Processable Bioplastics
Bioplastics are in focus for the development of sustainable materials due to the depletion of fossil resources, generation of solid waste and global climate change. Considering this, the current research is devoted to the valorization of beachcast red seaweed F. lumbricalis for the development of thermoplastically processable bioplastics. The composites have been developed from beachcast red seaweed-derived furcellaran (FUR) and potato-derived thermoplastic starch (TPS) by using an ultrasound-assisted technique. Three different FUR concentrations (10, 30 and 50 wt.%) in relation to potato starch were examined for their thermoplastic processability. Fourier infrared spectroscopy (FTIR) was used to reveal the structural changes in the developed TPS/FUR composites depending on FUR content as well as thermal pre-treatment. Thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and tensile mechanical tests were performed to assess the performance of the developed TPS/FUR composites. It was demonstrated that the ultrasound-assisted manufacturing route allowed TPS/FUR composites with an improved spectrum of properties to be obtained. The highest mechanical stress at break (almost three times higher than for neat TPS) was observed for the TPS + 50 wt.% FUR composite, which also possessed decreased deformability (only ca 10%), reduced thermal resistance at processing temperatures (150 °C) and high shear sensitivity. Thus, the TPS + 30 wt.% FUR and especially the TPS + 10 wt.% FUR composites were recognized as more suitable for thermoplastic processing and the development of TPS-based composites with improved exploitation properties.
- Open Access
- 5 February 2026
- Published by MDPI AG in Preprints.org
Use of Waste Red Seaweed Furceleran for Development of Green Thermoplastically Processable Bioplastics
The current research demonstrates boundaries of waste red seaweed furcellaran (FUR) for development of thermoplastically processable thermoplastic starch (TPS) compositions. Three different FUR concentrations (10, 30 and 50 wt.%) in relation to potato starch replacement were examined for their thermoplastic processability. Thermogravimetric (TGA), differential scanning calorimetry (DSC), rheology and tensile mechanical tests were performed to assess performance of the developed TPS/FUR compositions. It was observed that the highest mechanical stress at break (almost 3 times higher than for neat TPS) is observed for TPS+50wt.% FUR composition, however, on the account of decreased deformability (only ca 10%), reduced thermal resistance at processing temperatures (150oC) as well as high shear sensitivity. Thus compositions TPS+30wt.% FUR and especially TPS+10wt.% FUR are more suitable for thermoplastic processing and development of TPS based composites with improved exploitation properties.
- 5 February 2026
- Published by MDPI AG in Preprints.org
Open AccessUse of Waste Red Seaweed Furceleran for Development of Green Thermoplastically Processable Bioplastics
The current research demonstrates boundaries of waste red seaweed furcellaran (FUR) for development of thermoplastically processable thermoplastic starch (TPS) compositions. Three different FUR concentrations (10, 30 and 50 wt.%) in relation to potato starch replacement were examined for their thermoplastic processability. Thermogravimetric (TGA), differential scanning calorimetry (DSC), rheology and tensile mechanical tests were performed to assess performance of the developed TPS/FUR compositions. It was observed that the highest mechanical stress at break (almost 3 times higher than for neat TPS) is observed for TPS+50wt.% FUR composition, however, on the account of decreased deformability (only ca 10%), reduced thermal resistance at processing temperatures (150oC) as well as high shear sensitivity. Thus compositions TPS+30wt.% FUR and especially TPS+10wt.% FUR are more suitable for thermoplastic processing and development of TPS based composites with improved exploitation properties.