Monika Mich
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Monika Mich has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Chin Ping Tan
Department of Food Technology, Faculty of Food Science and Technology Universiti Putra Malaysia Serdang Selangor Malaysia
1 shared publication - Manit Say
Food Technology and Nutrition Research Unit, Research and Innovation Center, Institute of Technology of Cambodia, Russian Federation Blvd., P.O. Box 86, Phnom Penh, Cambodia
1 shared publication - Reasmey Tan
Research and Innovation Center, Institute of Technology of Cambodia, Russian Federation Blvd., Phnom Penh P.O. Box 86, Cambodia
1 shared publication - Sela Kong
Department of Research, University of Puthisastra, Phnom Penh 12211, Cambodia
1 shared publication - Yukleav Nat
Food Technology and Nutrition Research Unit, Research and Innovation Center, and Faculty of Chemical and Food Engineering, Institute of Technology of Cambodia, Russian Federation Blvd., P.O. Box 86, Phnom Penh, Cambodia
1 shared publication
Latest Publications
- Open Access
- 9 January 2023
- Published by Conscientia Beam in Journal of Food Technology Research
- Vol. 10 (1) , 1-10
Optimization of solvent extraction conditions of Cambodian soybean oil using response surface methodology
The conventional solvent extraction (CSE) method is commonly used to extract oil from oilseeds. Even though the extraction of oil from soybean seeds using the CSE method has been studied extensively, the application of response surface methodology (RSM) has not yet been widely explored. In this paper, the CSE method was employed using three different types of solvents – ethanol (Eth), n-hexane (Hex), and a mixture of Hex:Eth in a ratio of 2:1 – and optimized using RSM to extract the oil from Cambodian soybean seeds. For each solvent, a central composite design (CCD) was applied to optimize the extraction conditions, such as the extraction times (15, 30, and 45 min) and solvent-to-solid ratios (5:1, 10:1, and 15:1 mL/g). This CCD generated 11 experimental runs for each type of solvent. The optimum oil yields when using ethanol, Hex:Eth, and n-hexane were 20.53%, 18.78%, and 17.39%, respectively. The optimum condition was obtained at 15 min extraction time and 15:1 (mL/g) solvent-to-solid ratio for all solvent types. The coefficients of determination of ethanol, Hex:Eth, and n-hexane were 0.9710, 0.9954, and 0.9263, respectively, which mathematically indicated a good model for the prediction. Therefore, the model was considered accurate and reliable for predicting oil yields in this study.
- 9 January 2023
- Published by Conscientia Beam in Journal of Food Technology Research
- Vol. 10 (1) , 1-10
Open AccessOptimization of solvent extraction conditions of Cambodian soybean oil using response surface methodology
The conventional solvent extraction (CSE) method is commonly used to extract oil from oilseeds. Even though the extraction of oil from soybean seeds using the CSE method has been studied extensively, the application of response surface methodology (RSM) has not yet been widely explored. In this paper, the CSE method was employed using three different types of solvents – ethanol (Eth), n-hexane (Hex), and a mixture of Hex:Eth in a ratio of 2:1 – and optimized using RSM to extract the oil from Cambodian soybean seeds. For each solvent, a central composite design (CCD) was applied to optimize the extraction conditions, such as the extraction times (15, 30, and 45 min) and solvent-to-solid ratios (5:1, 10:1, and 15:1 mL/g). This CCD generated 11 experimental runs for each type of solvent. The optimum oil yields when using ethanol, Hex:Eth, and n-hexane were 20.53%, 18.78%, and 17.39%, respectively. The optimum condition was obtained at 15 min extraction time and 15:1 (mL/g) solvent-to-solid ratio for all solvent types. The coefficients of determination of ethanol, Hex:Eth, and n-hexane were 0.9710, 0.9954, and 0.9263, respectively, which mathematically indicated a good model for the prediction. Therefore, the model was considered accurate and reliable for predicting oil yields in this study.