Kamil Jendryka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kamil Jendryka has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Artur Kierzkowski
Department of Technical Systems Operation and Maintenance, Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, Smoluchowskiego 48, 50-372 Wroclaw, Poland
2 shared publications - Jakub Wróbel
Department of Technical Systems Operation and Maintenance, Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, 50-372 Wroclaw, Poland
2 shared publications - Maciej Milewski
Department of Technical Systems Operation and Maintenance, Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, Smoluchowskiego 48, 50-372 Wroclaw, Poland
2 shared publications - Michał Stosiak
Wroclaw University of Science and Technology
2 shared publications - Mykola Karpenko
Vilnius Gediminas Technical University
2 shared publications - Olegas Prentkovskis
Department of Mobile Machinery and Railway Transport, Vilnius Gediminas Technical University, Plytinės g. 27, LT-10105 Vilnius, Lithuania
2 shared publications
Latest Publications
- Open Access
Experimental Modal Testing of Lightweight Composite UAV Structures: Methods and Key Challenges
This study presents experimental modal analysis of an ultra-lightweight composite structure representative of UAV application and to evaluate the suitability of different testing approaches for reliable identification of its dynamics characteristics. The investigated structure is a winglet made of carbon fiber reinforced polymer (CFRP) with a lightweight foam core. The experiment was based on impact hammer excitation combined with triaxial accelerometer measurements. Modal tests were performed under three different boundary conditions: free–free suspension using elastic cords, free–free approximation using compliant foam support, and fixed conditions reflecting the operational mounting of the winglet. The results confirm that boundary conditions constitute the dominant factor governing the dynamic response. Transition from free–free to fixed support shifted the dominant bending modal frequency from 331.5 Hz (single-sided response) and 329.9 Hz (double-sided response) 421.2 Hz in the fixed configuration, demonstrating a frequency increase of nearly 27%. Reciprocity and double-sided measurements revealed measurable frequency deviations (e.g., 116.3 Hz to 117.6 Hz) attributed to accelerometer mass loading and geometric misalignment. The 1 g triaxial accelerometer mass was shown to be non-negligible relative to the modal mass of the structure, producing observable shifts in higher-order modes.
Open AccessExperimental Modal Testing of Lightweight Composite UAV Structures: Methods and Key Challenges
This study presents experimental modal analysis of an ultra-lightweight composite structure representative of UAV application and to evaluate the suitability of different testing approaches for reliable identification of its dynamics characteristics. The investigated structure is a winglet made of carbon fiber reinforced polymer (CFRP) with a lightweight foam core. The experiment was based on impact hammer excitation combined with triaxial accelerometer measurements. Modal tests were performed under three different boundary conditions: free–free suspension using elastic cords, free–free approximation using compliant foam support, and fixed conditions reflecting the operational mounting of the winglet. The results confirm that boundary conditions constitute the dominant factor governing the dynamic response. Transition from free–free to fixed support shifted the dominant bending modal frequency from 331.5 Hz (single-sided response) and 329.9 Hz (double-sided response) 421.2 Hz in the fixed configuration, demonstrating a frequency increase of nearly 27%. Reciprocity and double-sided measurements revealed measurable frequency deviations (e.g., 116.3 Hz to 117.6 Hz) attributed to accelerometer mass loading and geometric misalignment. The 1 g triaxial accelerometer mass was shown to be non-negligible relative to the modal mass of the structure, producing observable shifts in higher-order modes.
- Open Access
- 14 February 2026
- Published by MDPI AG in Preprints.org
Experimental Modal Testing of Lightweight Composite UAV Structures: Methods and Key Challenges
This study aims to conduct and experimental modal analysis of a very lightweight composite structure representative of UAV application and to evaluate the suitability of different testing approaches for reliable identification of its dynamics characteristics. The investigated structure is a winglet made of carbon fibre reinforced polymer (CFRP) with a lightweight foam core. The experimental campaign was based on impact hammer excitation combined with triaxial accelerometer measurements. Modal test were performed under three different boundary conditions: free-free suspension using elastic cords, free-free approximation using compliant foam support, and fixed conditions reflecting to the operational mounting of the winglet. The objective of the study is not only to identify natural frequencies and mode shapes, but primarily to assess the influence of support conditions, excitation quality and measurement-induced mass loading on the reliability of the extracted modal parameters. By comparing the obtained frequency response functions and modal characteristics across different test configurations, the work seeks to identify the most appropriate experimental approach for modal analysis of ultra-lightweight composite UAV structures, providing practical guidance for future vibration investigations.
- 14 February 2026
- Published by MDPI AG in Preprints.org
Open AccessExperimental Modal Testing of Lightweight Composite UAV Structures: Methods and Key Challenges
This study aims to conduct and experimental modal analysis of a very lightweight composite structure representative of UAV application and to evaluate the suitability of different testing approaches for reliable identification of its dynamics characteristics. The investigated structure is a winglet made of carbon fibre reinforced polymer (CFRP) with a lightweight foam core. The experimental campaign was based on impact hammer excitation combined with triaxial accelerometer measurements. Modal test were performed under three different boundary conditions: free-free suspension using elastic cords, free-free approximation using compliant foam support, and fixed conditions reflecting to the operational mounting of the winglet. The objective of the study is not only to identify natural frequencies and mode shapes, but primarily to assess the influence of support conditions, excitation quality and measurement-induced mass loading on the reliability of the extracted modal parameters. By comparing the obtained frequency response functions and modal characteristics across different test configurations, the work seeks to identify the most appropriate experimental approach for modal analysis of ultra-lightweight composite UAV structures, providing practical guidance for future vibration investigations.