Jānis Narbuts
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jānis Narbuts has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Andra Blumberga
Riga Technical University
1 shared publication - Ritvars Freimanis
Institute of Energy Systems and Environment, Riga Technical University, LV1048 Riga, Latvia
1 shared publication - Ruta Vanaga
Institute of Energy Systems and Environment, Riga Technical University, LV1048 Riga, Latvia
1 shared publication
Latest Publications
- 1 June 2026
- Published by Riga Technical University
Siltumenerģiju uzkrājošas adaptīvās fasāžu sistēmas
Promocijas darbā izstrādāta adaptīva saules fasādes sistēma ar fāžu pārejas materiāliem siltumenerģijas uzkrāšanai un analizēta tās ietekme uz ēku energoefektivitāti laboratorijas un reālos klimatiskajos apstākļos. Pētījumā izmantotas eksperimentālās un skaitliskās modelēšanas metodes. Rezultāti parāda, ka izstrādātā tehnoloģija spēj samazināt temperatūras svārstības un apkures/dzesēšanas enerģijas patēriņu.
- 1 June 2026
- Published by Riga Technical University
Siltumenerģiju uzkrājošas adaptīvās fasāžu sistēmas
Promocijas darbā izstrādāta adaptīva saules fasādes sistēma ar fāžu pārejas materiāliem siltumenerģijas uzkrāšanai un analizēta tās ietekme uz ēku energoefektivitāti laboratorijas un reālos klimatiskajos apstākļos. Pētījumā izmantotas eksperimentālās un skaitliskās modelēšanas metodes. Rezultāti parāda, ka izstrādātā tehnoloģija spēj samazināt temperatūras svārstības un apkures/dzesēšanas enerģijas patēriņu.
- 1 June 2026
- Published by Riga Technical University
Adaptive Building Facade Systems with Thermal Energy Storage
This Thesis presents the development of an adaptive solar facade system integrating phase change materials for thermal energy storage and evaluates its impact on building energy efficiency under both laboratory and real climatic conditions. Experimental investigations and numerical simulations were applied throughout the research. The results demonstrate that the developed technology can reduce indoor temperature fluctuations and decrease heating and cooling energy demand.
- 1 June 2026
- Published by Riga Technical University
Adaptive Building Facade Systems with Thermal Energy Storage
This Thesis presents the development of an adaptive solar facade system integrating phase change materials for thermal energy storage and evaluates its impact on building energy efficiency under both laboratory and real climatic conditions. Experimental investigations and numerical simulations were applied throughout the research. The results demonstrate that the developed technology can reduce indoor temperature fluctuations and decrease heating and cooling energy demand.
- Open Access
- 1 January 2021
- Published by Walter de Gruyter GmbH in Environmental and Climate Technologies
- Vol. 25 (1) , 455-466
Laboratory Testing of Small-Scale Active Solar Façade Module
Buildings are linked to a significant untapped energy saving potential, accounting for 40 % of European Union’s (EU) final energy and 36 % of CO2 emissions. Energy efficient building envelopes plays the key role to achieve decarbonization of the EU’s building stock by 2050. Active building envelopes are emerging and novel trend offering the paradigm shift in perception of building enclosures. Paper presents study of active solar façade containing phase change material for energy storage. Study seeks for optimisation of solar façade module by introducing dynamic component and variating in the composition of module itself to ensure faster energy harvesting and minimise the heat losses at discharging phase. Comparative tests were carried out in laboratory, in controlled heating and cooling conditions to evaluate impact of dynamic component. The dynamic component has reflective inner coating that focuses solar radiation on the element in heating phase and aerogel insulation filling in the blades that decreases heat loss in the cooling phase. Varying components in the design were used– thickness of aerogel insulation, Fresnel lens and width of concentrating cone diameter. Wide range of phase change material average temperature was observed 24 °C in setups with full aerogel filling to 50 °C in setup Fresnel lens. Average temperature in phase change material was reached higher in all setups with dynamic component compared to identical setups without dynamic component. Temperature differences were in the range from 1 °C in aerogel filled setups till 6 °C in setups with Fresnel lens.
- 1 January 2021
- Published by Walter de Gruyter GmbH in Environmental and Climate Technologies
- Vol. 25 (1) , 455-466
Open AccessLaboratory Testing of Small-Scale Active Solar Façade Module
Buildings are linked to a significant untapped energy saving potential, accounting for 40 % of European Union’s (EU) final energy and 36 % of CO2 emissions. Energy efficient building envelopes plays the key role to achieve decarbonization of the EU’s building stock by 2050. Active building envelopes are emerging and novel trend offering the paradigm shift in perception of building enclosures. Paper presents study of active solar façade containing phase change material for energy storage. Study seeks for optimisation of solar façade module by introducing dynamic component and variating in the composition of module itself to ensure faster energy harvesting and minimise the heat losses at discharging phase. Comparative tests were carried out in laboratory, in controlled heating and cooling conditions to evaluate impact of dynamic component. The dynamic component has reflective inner coating that focuses solar radiation on the element in heating phase and aerogel insulation filling in the blades that decreases heat loss in the cooling phase. Varying components in the design were used– thickness of aerogel insulation, Fresnel lens and width of concentrating cone diameter. Wide range of phase change material average temperature was observed 24 °C in setups with full aerogel filling to 50 °C in setup Fresnel lens. Average temperature in phase change material was reached higher in all setups with dynamic component compared to identical setups without dynamic component. Temperature differences were in the range from 1 °C in aerogel filled setups till 6 °C in setups with Fresnel lens.