Eugen Gavan
Research Subjects
Eugen Gavan has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Alina Descalui
1 shared publication- Carmen Gasparotti
Faculty of Naval Architecture, “Dunarea de Jos” University of Galati, 800201 Galati, Romania
1 shared publication - Costel Ungureanu
Faculty of Naval Architecture, “Dunarea de Jos” University of Galati, 800201 Galati, Romania
1 shared publication Dragoş Alexandru Saragea
1 shared publication- Ion Ion
Faculty of Naval Architecture, “Dunărea de Jos” University of Galați, Domnească St., No. 111, 800008 Galați, Romania
1 shared publication Marcel Drăgan
1 shared publication
Latest Publications
- 13 December 2025
- Published by Universitatea Dunarea de Jos din Galati in Analele Universităţii "Dunărea de Jos" din Galaţi Fascicula XI Construcţii navale/ Annals of "Dunărea de Jos" of Galati Fascicle XI Shipbuilding
- Vol. 48, 181-184
Local structural analysys of potable water system foundation
This paper presents the local structural analysis of a steel foundation supporting the pumps of a potable water system installed on a 30,000 DWT Handymax bulk carrier. The aim is to evaluate the structural behaviour of the foundation under static and dynamic loads representative for shipboard service and to propose simple constructive improvements that enhance stiffness and vibration performance. The potable water system is briefly described, including design requirements, sizing of the pumps, hydrophore unit and heat exchanger. The support structure is modelled in 3D CAD and analysed using the finite element method in ANSYS Mechanical, considering the mass of the pump unit and excitation frequencies up to 60 Hz. Three foundation variants are investigated: the initial design, a stiffened version obtained by adding local reinforcements and an alternative closed-section frame using rectangular hollow profiles. For each model, deformations and equivalent von Mises stresses are evaluated and compared with the yield limit of steel S235JR and with serviceability criteria from Eurocode 3. The results show that the optimized foundation with rectangular hollow sections significantly reduces maximum deformations and improves dynamic behaviour, without exceeding allowable stress levels. Recommendations for monitoring, maintenance and vibration isolation using spring-type anti-vibration mounts are also formulated.
- 13 December 2025
- Published by Universitatea Dunarea de Jos din Galati in Analele Universităţii "Dunărea de Jos" din Galaţi Fascicula XI Construcţii navale/ Annals of "Dunărea de Jos" of Galati Fascicle XI Shipbuilding
- Vol. 48, 181-184
Local structural analysys of potable water system foundation
This paper presents the local structural analysis of a steel foundation supporting the pumps of a potable water system installed on a 30,000 DWT Handymax bulk carrier. The aim is to evaluate the structural behaviour of the foundation under static and dynamic loads representative for shipboard service and to propose simple constructive improvements that enhance stiffness and vibration performance. The potable water system is briefly described, including design requirements, sizing of the pumps, hydrophore unit and heat exchanger. The support structure is modelled in 3D CAD and analysed using the finite element method in ANSYS Mechanical, considering the mass of the pump unit and excitation frequencies up to 60 Hz. Three foundation variants are investigated: the initial design, a stiffened version obtained by adding local reinforcements and an alternative closed-section frame using rectangular hollow profiles. For each model, deformations and equivalent von Mises stresses are evaluated and compared with the yield limit of steel S235JR and with serviceability criteria from Eurocode 3. The results show that the optimized foundation with rectangular hollow sections significantly reduces maximum deformations and improves dynamic behaviour, without exceeding allowable stress levels. Recommendations for monitoring, maintenance and vibration isolation using spring-type anti-vibration mounts are also formulated.
- 13 December 2025
- Published by Universitatea Dunarea de Jos din Galati in Analele Universităţii "Dunărea de Jos" din Galaţi Fascicula XI Construcţii navale/ Annals of "Dunărea de Jos" of Galati Fascicle XI Shipbuilding
- Vol. 48, 159-166
Performance enhancement of marine inert gas generator with combustion
The heat generated in the combustion inert gas generator (IGG) is usually discharged with flue gas cooling water. This paper proposes a system for recovering part of the heat generated in the IGG and using it in an absorption chiller for advanced cooling of the inert gas. The thermodynamic analysis showed that for an IGG consuming 240 kg/h of marine gas oil, 132 kW can be recovered to drive a lithium bromide-water absorption chiller, which can cool the inert gas down to 15°C, a temperature at which the water vapor content of the inert gas is 12.79 g/m3, much lower than if the inert gas is cooled only down to 50°C (82.5 g/m3) as it is done in most IGGs. By recovering waste heat, the quality of the inert gas is improved (humidity is reduced) without additional energy consumption.
- 13 December 2025
- Published by Universitatea Dunarea de Jos din Galati in Analele Universităţii "Dunărea de Jos" din Galaţi Fascicula XI Construcţii navale/ Annals of "Dunărea de Jos" of Galati Fascicle XI Shipbuilding
- Vol. 48, 159-166
Performance enhancement of marine inert gas generator with combustion
The heat generated in the combustion inert gas generator (IGG) is usually discharged with flue gas cooling water. This paper proposes a system for recovering part of the heat generated in the IGG and using it in an absorption chiller for advanced cooling of the inert gas. The thermodynamic analysis showed that for an IGG consuming 240 kg/h of marine gas oil, 132 kW can be recovered to drive a lithium bromide-water absorption chiller, which can cool the inert gas down to 15°C, a temperature at which the water vapor content of the inert gas is 12.79 g/m3, much lower than if the inert gas is cooled only down to 50°C (82.5 g/m3) as it is done in most IGGs. By recovering waste heat, the quality of the inert gas is improved (humidity is reduced) without additional energy consumption.