ZJZhazira Julayeva

Zhazira Julayeva

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zhazira Julayeva has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Development and Software-in-the-Loop Validation of a Digital Twin Architecture for District Heating Networks

    by Ainagul Seitbekova, Irbulat Utepbergenov, Laulasyn Abzhanova, Zhazira Julayeva, Iouliia Skliarova, Maxat Orunbekov

    In this study, a digital-twin-oriented integration architecture was developed for district heating networks in a laboratory Software-in-the-Loop (SIL) environment and evaluated. The implemented testbed combined a virtual SIMATIC S7-1500 controller executed in S7-PLCSIM Advanced V8.0, WinCC Runtime Advanced, OPC UA communication, a Python-based integration layer, and a Fluidit Heat thermohydraulic model. The physical district heating network, field sensors, pumps, actuators, and an operational field PLC were not connected to the experimental loop. Field-derived heat load and pressure values for five monitored consumers were stored in PLC data blocks. Python validated and mapped the tags, initiated predefined Fluidit Heat scenarios, processed the model outputs, and returned the results to the PLC for SCADA visualization. Six operating scenarios were evaluated. In the combined baseline and 120% demand scenarios, the delivered heat increased from 2369.84 to 2843.79 kW, plant thermal output from 2377.14 to 2850.80 kW, and plant flow from 12.288 to 14.737 L/s. The maximum supply velocity increased from 1.192 to 1.430 m/s, and the maximum unit pressure loss increased from 1.338 to 1.912 bar/km (+42.92%). The minimum consumer differential pressure remained at approximately 4.000 bar, above the adopted 3.5 bar criterion, and no heat deficit was calculated. The experiment demonstrated functional software interoperability, event-driven scenario execution, and bidirectional simulation data exchange. Because the baseline values contributed to model parameterization and the physical network was not connected, the comparison was a consistency assessment rather than independent field validation. Automatic optimization, autonomous preferred-mode selection, and actuator-level control were not implemented.

  • Open Access

    Radio-Quality-Aware Model Predictive Control for Industrial Wireless Control Networks

    by Anar Khabay, Akerke Baurzhan, Amandyk Tuleshov, Moldir Kuatova, Nurgul Smailova, Bauyrzhan Bazarbay, Ainur Ormanbekova, Zhazira Julayeva, Yerkebulan Tuleshov

    Industrial wireless sensor and actuator networks are increasingly used in closed-loop control systems. In such systems, packet dropout, channel degradation, and communication delay can deteriorate tracking performance. This paper proposes a Radio-Quality-Aware Model Predictive Control (MPC) strategy for an industrial conveyor drive system operating under time-varying wireless communication conditions. Unlike classical MPC, the proposed controller incorporates radio-channel information, including the signal-to-interference-plus-noise ratio (SINR), packet error rate (PER), and network-induced delay, into the predictive control formulation, thereby adapting the control action to degraded communication conditions. In the MATLAB simulations, an industrial load torque profile based on sensor-measured signals was used, and the wireless communication scenario was divided into three regions representing favorable, moderately degraded, and severely degraded conditions. The results demonstrate that the proposed MPC maintains the angular speed closer to its reference value than the classical MPC, particularly under severe degradation when the SINR decreases to 5 dB. Compared with the classical MPC, the proposed Radio-Quality-Aware MPC reduces the integral of absolute error (IAE) by approximately 90.6%, the root mean square error (RMSE) by 91.4%, the maximum absolute tracking error by 92.7%, and the input variation index by 67.2%, while maintaining a comparable level of control energy. Overall, these results demonstrate that the proposed Radio-Quality-Aware Model Predictive Control framework improves tracking accuracy, actuator smoothness, and system robustness in industrial wireless control applications.


  • Open Access

    Modeling a Railway Section to Assess the Effectiveness of Fixed- and Moving-Block Systems

    by Maxat Orunbekov, Bagdat Teltayev, Gulfariza Suleimenova, Nurgul Karymsakova, Zhazira Julayeva, Zhanibek Shukamanov

    This study was carried out to determine the reliability of the methods of transmission of information about the location of a train to the train control center using a digital radio channel and a method based on Distributed Acoustic Sensing (DAS) technology. The study results were obtained based on the MATLAB R2024b model and showed resistance to external noise in fiber-optic communication with DAS technology. The proposed information transmission method allows the joint use of fixed- and moving-block section concepts in train traffic control systems. The effectiveness of the joint application of the concept of fixed and moving-block sections was analyzed using OpenTrack V1.10 microscopic simulation using the parameters of the operating railway section Kurozek-Ekpindi-Jarsu, locomotive TE33A series, trains No. 3002 and No. 3004, and the interval control system. The obtained research results in the form of a diagram showed the effectiveness of the proposed method of duplicating the concept of moving- and fixed-block sections. The reduction in inter-train intervals contributes to increasing the capacity of the railway line and is the key to the economic efficiency of railway transport.