SYShichen Yan

Shichen Yan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Shichen Yan has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of Preheating Temperature on Microstructure and Mechanical Properties of TIG Welded Joints of Low-Activity Martensitic Steel

    by Yinglong Zhang, Shichen Yan, Hongpeng Zhang, Xiaoquan Yu, Chen Dong, Cunfeng Yao, Jiankang Huang

    The effects of preheating temperature on the microstructural evolution and mechanical properties of low-activity martensitic steel welded joints were investigated, with emphasis on the relationship between preheating temperature, δ-ferrite content, and impact energy. Preheating temperature ranged from 150 °C to 300 °C. Optical microscopy and TEM were used for microstructural characterization, and tensile and impact tests were conducted to evaluate mechanical properties. The results showed that preheating temperature influenced the retained δ-ferrite content in the weld metal, whereas its effect on the heat-affected-zone microstructure was comparatively limited. The δ-ferrite fraction exhibited a non-monotonic dependence on preheating temperature, reaching a minimum of 2.76% in the filler weld pass at 250 °C. As the δ-ferrite fraction increased to approximately 13.27% at 150 °C, the average impact energy of the weld metal decreased from 47.37 J at 250 °C to 34.57 J at 150 °C. Impact fracture analysis revealed preferential crack propagation along δ ferrite/martensite interfaces and through δ-ferrite grains. An increase in the δ-ferrite fraction may promote the formation of interconnected ferrite networks, thereby facilitating crack propagation and reducing the impact toughness of the weld metal.

  • Open Access

    Study of the Microstructure and Properties of CoCrFeNiMnx High-Entropy Alloys

    by Zhengpeng Zhang, Shichen Yan, Jiankang Huang, Tianxiang Zhao, Chen Dong, Abdul Bari, Jiaojiao Xie, Xiaoquan Yu, Yingwei Chen

    High-entropy alloys (HEAs) provide a broad compositional space for tuning phase stability and surface durability. CoCrFeNiMnx (x = 0.5, 1.0, 1.5, and 2.0) alloys were fabricated by vacuum arc melting and characterized by X-ray diffraction (XRD), optical microscopy (OM), scanning electron microscopy with energy-dispersive spectroscopy (SEM/EDS), microhardness testing, electrochemical testing in 3.5 wt.% NaCl, and X-ray photoelectron spectroscopy (XPS). Density functional theory (DFT) calculations and first-principles molecular dynamics were further employed to analyze the Mn-dependent electronic structure and oxygen–metal bonding. The XRD results indicate a transition from a single FCC solid solution at x ≤ 1.0 to an FCC + BCC constitution at x ≥ 1.5. With increasing Mn, microstructures evolve from coarse dendrites toward higher fractions of equiaxed grains. Hardness decreases from 163.6 HV (x = 0.5) to 125.1 HV (x = 1.0) and then increases to 162.6 HV (x = 2.0), indicating competing solid-solution and phase/segregation effects. Electrochemical measurements show enhanced corrosion resistance with Mn addition; the x = 2.0 alloy exhibits the lowest fitted corrosion current density (icorr = 0.3482 × 10−6 μA·cm−2) and the most stable passivation response. XPS reveals passive films dominated by Fe2O3 together with Mn3+ oxides, whose synergistic formation promotes a denser barrier layer. DFT predicts a monotonic decrease in Fermi level and a narrowed conduction band range as Mn increases, consistent with reduced electron transfer activity during anodic dissolution. Interfacial simulations show that O preferentially bonds with Cr and Mn, while Ni–O bonds have the lowest estimated rupture barrier, rationalizing a tendency toward localized corrosion at Ni-associated sites.