Emanuele Rimini
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Emanuele Rimini has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
V. Raineri
CNR-IMETEM, Stradale Primosole 50, 95121 Catania, Italy
5 shared publications- Alessandra Alberti
CNR-IMM
3 shared publications - Francesco Priolo
University of Catania
3 shared publications G. Galvagno
INFM and Dipartimento di Fisica, Università di Catania, Corso Italia 57, 95129 Catania, Italy
3 shared publicationsA. La Ferla
INFM and Dipartimento di Fisica, Università di Catania, Corso Italia 57, 95129 Catania, Italy
2 shared publications- Corrado Bongiorno
CNR-IMM
2 shared publications
Latest Publications
- Open Access
- 29 June 2026
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 20 (7)
Simultaneous Deposition of Different Phase‐Change Alloys Through a Nanopillars Shadow Procedure
Phase Change Memory is a leading emerging nonvolatile memory technology based on the reversible switching between amorphous and crystalline states in Ge‐Sb‐Te alloys. Repeated phase transitions induce elemental redistribution, generating local stoichiometry variations that critically influence device performance. Accessing different compositions within a single specimen is therefore essential for understanding phase change memory (PCM) behavior. We present a deposition methodology enabling the simultaneous formation of phase‐change alloys with nanoscale compositional gradients. The approach uses three Knudsen cells supplying Ge, Sb, and Te, each oriented at 45° relative to the substrate normal. The substrate includes cylindrical nanopillar arrays produced by electron beam lithography, which generate controlled shadowing effects and spatial modulation of the elemental flux. Local composition was characterized using scanning transmission electron microscopy and electron energy loss spectroscopy. The elemental profiles were compared with a ballistic transport model describing trajectories around nanopillars. The experimental and simulated data show agreement. Simulations performed with an alternative configuration, where the three cells are spaced 120°, predict predefined Ge, Sb, and Te‐deficient regions around the pillars. This methodology enables controlled nanoscale stoichiometry engineering and provides a powerful platform for studying composition‐dependent phase‐change mechanisms, supporting the optimization of PCM device performance.
- 29 June 2026
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 20 (7)
Open AccessSimultaneous Deposition of Different Phase‐Change Alloys Through a Nanopillars Shadow Procedure
Phase Change Memory is a leading emerging nonvolatile memory technology based on the reversible switching between amorphous and crystalline states in Ge‐Sb‐Te alloys. Repeated phase transitions induce elemental redistribution, generating local stoichiometry variations that critically influence device performance. Accessing different compositions within a single specimen is therefore essential for understanding phase change memory (PCM) behavior. We present a deposition methodology enabling the simultaneous formation of phase‐change alloys with nanoscale compositional gradients. The approach uses three Knudsen cells supplying Ge, Sb, and Te, each oriented at 45° relative to the substrate normal. The substrate includes cylindrical nanopillar arrays produced by electron beam lithography, which generate controlled shadowing effects and spatial modulation of the elemental flux. Local composition was characterized using scanning transmission electron microscopy and electron energy loss spectroscopy. The elemental profiles were compared with a ballistic transport model describing trajectories around nanopillars. The experimental and simulated data show agreement. Simulations performed with an alternative configuration, where the three cells are spaced 120°, predict predefined Ge, Sb, and Te‐deficient regions around the pillars. This methodology enables controlled nanoscale stoichiometry engineering and provides a powerful platform for studying composition‐dependent phase‐change mechanisms, supporting the optimization of PCM device performance.
- Open Access
- 16 October 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 128 (15) , 155105
Crystallization properties of melt-quenched Ge-rich GeSbTe thin films for phase change memory applications
The crystallization process of melt quenched Ge-rich GeSbTe films, with composition optimized for memory applications, has been studied by optical reflectance measurements. The optical properties have been related to the structure and composition by means of the effective medium approximation. The compositional variations have been investigated by transmission electron microscopy and electron energy loss spectroscopy. Amorphous materials prepared by melt-quenching with different laser energy densities have been studied. For the energy density of 1.5 J cm−2, a uniform amorphous layer, with embedded Ge crystalline grains, is obtained. The film exhibits a crystallization temperature of 275 °C and no relevant phase separation during crystallization. For a lower energy density of 1 J cm−2, only half of the film thickness is quenched to the amorphous phase, with Ge depletion. The crystallization temperature of the Ge depleted film is 245 °C, and a partial phase separation occurs.
- 16 October 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 128 (15) , 155105
Open AccessCrystallization properties of melt-quenched Ge-rich GeSbTe thin films for phase change memory applications
The crystallization process of melt quenched Ge-rich GeSbTe films, with composition optimized for memory applications, has been studied by optical reflectance measurements. The optical properties have been related to the structure and composition by means of the effective medium approximation. The compositional variations have been investigated by transmission electron microscopy and electron energy loss spectroscopy. Amorphous materials prepared by melt-quenching with different laser energy densities have been studied. For the energy density of 1.5 J cm−2, a uniform amorphous layer, with embedded Ge crystalline grains, is obtained. The film exhibits a crystallization temperature of 275 °C and no relevant phase separation during crystallization. For a lower energy density of 1 J cm−2, only half of the film thickness is quenched to the amorphous phase, with Ge depletion. The crystallization temperature of the Ge depleted film is 245 °C, and a partial phase separation occurs.
- Open Access
- 23 September 2005
- Published by International Union of Crystallography (IUCr) in Acta crystallographica Section B, Structural science, crystal engineering and materials
- Vol. 61 (5) , 486-491
Pseudoepitaxial transrotational structures in 14 nm-thick NiSi layers on [001] silicon
In a system consisting of two different lattices, structural stability is ensured when an epitaxial relationship occurs between them and allows the system to retain the stress whilst avoiding the formation of a polycrystalline film. The phenomenon occurs if the film thickness does not exceed a critical value. Here we show that in spite of its orthorhombic structure, a 14 nm-thick NiSi layer can three-dimensionally adapt to the cubic Si lattice by forming transrotational domains. Each domain arises by the continuous bending of the NiSi lattice, maintaining a close relationship with the substrate structure. The presence of transrotational domains does not cause a roughening of the layer, but instead it improves the structural and electrical stability of the silicide in comparison with a 24 nm-thick layer formed using the same annealing process. These results have relevant implications for the thickness scaling of NiSi layers which are currently used as metallizations of electronic devices.
- 23 September 2005
- Published by International Union of Crystallography (IUCr) in Acta crystallographica Section B, Structural science, crystal engineering and materials
- Vol. 61 (5) , 486-491
Open AccessPseudoepitaxial transrotational structures in 14 nm-thick NiSi layers on [001] silicon
In a system consisting of two different lattices, structural stability is ensured when an epitaxial relationship occurs between them and allows the system to retain the stress whilst avoiding the formation of a polycrystalline film. The phenomenon occurs if the film thickness does not exceed a critical value. Here we show that in spite of its orthorhombic structure, a 14 nm-thick NiSi layer can three-dimensionally adapt to the cubic Si lattice by forming transrotational domains. Each domain arises by the continuous bending of the NiSi lattice, maintaining a close relationship with the substrate structure. The presence of transrotational domains does not cause a roughening of the layer, but instead it improves the structural and electrical stability of the silicide in comparison with a 24 nm-thick layer formed using the same annealing process. These results have relevant implications for the thickness scaling of NiSi layers which are currently used as metallizations of electronic devices.
- 15 April 2001
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 89 (8) , 4310-4317
Photoluminescence and structural studies on extended defect evolution during high-temperature processing of ion-implanted epitaxial silicon
Low-temperaturephotoluminescence (PL) spectroscopy, in conjunction withtransmission electron microscopy (TEM) andoptical microscopy (OM) have been carried out to investigate the origin of radiative recombination from various extended defects that evolve during high-temperature processing of ion-implantedepitaxial silicon. FromPL studies on samples, we providespectroscopic evidence ofprecipitation of the implanted impurities well below the solid-solubility limit. This result is being supported by observations from secondary ion mass spectrometry and spreading resistance profiling of the implanted ions. Cross sectionalTEM analyses on these samples reveal 〈111〉-oriented precipitates located in a region containing a high dislocation density. Postimplantation annealing in oxygen ambient results in the formation of dislocations and oxidation-induced stacking faults (OISF). A systematicanalysis ofPL spectra on different-implanted and preannealed samples, in conjunction withTEM andOM analyses, reveals that the conventionally observed dislocation-related D1 and D2 lines in thePL spectrum is not a characteristic of the OISF, but of the dislocations only. It is shown that the OISF acts as a nonradiative channel for luminescence insilicon. Various other sources of nonradiative channels insilicon are also presented and the efficacy ofphotoluminescence technique in the characterization of process-induced defects insilicon is discussed.- 15 April 2001
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 89 (8) , 4310-4317
Photoluminescence and structural studies on extended defect evolution during high-temperature processing of ion-implanted epitaxial silicon
Low-temperaturephotoluminescence (PL) spectroscopy, in conjunction withtransmission electron microscopy (TEM) andoptical microscopy (OM) have been carried out to investigate the origin of radiative recombination from various extended defects that evolve during high-temperature processing of ion-implantedepitaxial silicon. FromPL studies on samples, we providespectroscopic evidence ofprecipitation of the implanted impurities well below the solid-solubility limit. This result is being supported by observations from secondary ion mass spectrometry and spreading resistance profiling of the implanted ions. Cross sectionalTEM analyses on these samples reveal 〈111〉-oriented precipitates located in a region containing a high dislocation density. Postimplantation annealing in oxygen ambient results in the formation of dislocations and oxidation-induced stacking faults (OISF). A systematicanalysis ofPL spectra on different-implanted and preannealed samples, in conjunction withTEM andOM analyses, reveals that the conventionally observed dislocation-related D1 and D2 lines in thePL spectrum is not a characteristic of the OISF, but of the dislocations only. It is shown that the OISF acts as a nonradiative channel for luminescence insilicon. Various other sources of nonradiative channels insilicon are also presented and the efficacy ofphotoluminescence technique in the characterization of process-induced defects insilicon is discussed.- 3 November 1999
- Published by AIP Publishing in Applied Physics Letters
- Vol. 75 (19) , 2924-2926
Structural relationship of polycrystalline cobalt silicide lines to (001) silicon substrate
A local investigation of the structural properties of polycrystalline strips onto (001) Si wafers has been performed by transmission electron microscopy. crystal grains exhibit different behavior depending upon their position within the line. Grains close to the center of the strip are randomly oriented, while most of the grains at the edge of the strip grow epitaxially, obeying three different epitaxial relationships. Some of these grains maintain the substrate orientation with the presence of twin defects. High-resolution analysis demonstrates the presence of misfit dislocations at the interface, which accommodates the lattice mismatch.- 3 November 1999
- Published by AIP Publishing in Applied Physics Letters
- Vol. 75 (19) , 2924-2926
Structural relationship of polycrystalline cobalt silicide lines to (001) silicon substrate
A local investigation of the structural properties of polycrystalline strips onto (001) Si wafers has been performed by transmission electron microscopy. crystal grains exhibit different behavior depending upon their position within the line. Grains close to the center of the strip are randomly oriented, while most of the grains at the edge of the strip grow epitaxially, obeying three different epitaxial relationships. Some of these grains maintain the substrate orientation with the presence of twin defects. High-resolution analysis demonstrates the presence of misfit dislocations at the interface, which accommodates the lattice mismatch.- 1 May 1998
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 16 (3) , 1129-1136
Thermal stability of thin CoSi2 layers on polysilicon implanted with As, BF2, and Si
The thermal stability of thin cobalt silicide layers grown on preamorphized chemical vapor deposited silicon layers has been studied in the temperature range between 950 and 1100 °C. The morphology of the starting layers and their evolution during the thermal processes was analyzed by transmission electron microscopy, atomic force microscopy and Rutherford backscattering spectroscopy. The observed increase in sheet resistance with the annealing time has been correlated to the agglomeration process taking into account the dependence of the resistivity on film thickness and carrier mean free path. Sheet resistance measurements have been used to study the agglomeration process of CoSi2 by varying temperature and substrate doping (As, BF2, and Si implants). The process is thermally activated with an activation energy of 4.3 eV for the Si implanted samples. The BF2 implanted substrate show a higher activation energy (∼5.4 eV), while the arsenic implanted a lower one (∼3.6 eV). This difference is attributed to the weakening of the Co–Si bonds by arsenic atoms and to the presence of some fluorine precipitates at the CoSi2/Si interface that increase the energy needed for the reaction at the silicide/silicon interface.
- 1 May 1998
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 16 (3) , 1129-1136
Thermal stability of thin CoSi2 layers on polysilicon implanted with As, BF2, and Si
The thermal stability of thin cobalt silicide layers grown on preamorphized chemical vapor deposited silicon layers has been studied in the temperature range between 950 and 1100 °C. The morphology of the starting layers and their evolution during the thermal processes was analyzed by transmission electron microscopy, atomic force microscopy and Rutherford backscattering spectroscopy. The observed increase in sheet resistance with the annealing time has been correlated to the agglomeration process taking into account the dependence of the resistivity on film thickness and carrier mean free path. Sheet resistance measurements have been used to study the agglomeration process of CoSi2 by varying temperature and substrate doping (As, BF2, and Si implants). The process is thermally activated with an activation energy of 4.3 eV for the Si implanted samples. The BF2 implanted substrate show a higher activation energy (∼5.4 eV), while the arsenic implanted a lower one (∼3.6 eV). This difference is attributed to the weakening of the Co–Si bonds by arsenic atoms and to the presence of some fluorine precipitates at the CoSi2/Si interface that increase the energy needed for the reaction at the silicide/silicon interface.
- 1 December 1995
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
- Vol. 106 (1-4) , 419-423
Impurity effects on oxygen precipitation induced by MeV implants in Cz silicon
- 1 December 1995
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
- Vol. 106 (1-4) , 419-423
Impurity effects on oxygen precipitation induced by MeV implants in Cz silicon
- 1 March 1995
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
- Vol. 96 (1-2) , 144-149
Mask edge effects in high energy implants: dopant and defect distributions
- 1 March 1995
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
- Vol. 96 (1-2) , 144-149
Mask edge effects in high energy implants: dopant and defect distributions
- 1 January 1992
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
- Vol. 62 (3) , 331-337
High energy P implants in silicon
- 1 January 1992
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
- Vol. 62 (3) , 331-337
High energy P implants in silicon
- 1 April 1991
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
- Vol. 55 (1-4) , 611-614
Evolution of low-fluence heavy-ion damage in Si under high energy ion irradiation
- 1 April 1991
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
- Vol. 55 (1-4) , 611-614
Evolution of low-fluence heavy-ion damage in Si under high energy ion irradiation