Agusti Sin
Research Subjects
Research Interests
Agusti Sin has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Francois Weiss
Centre National de la Recherche Scientifique
2 shared publications P. Odier
Laboratoire de Cristallographie, CNRS, BP166, 38042 Grenoble Cedex 09, France
2 shared publicationsA. Sulpice
Centre de Recherche sur les Très Basses Températures-CNRS, 25 Av. des Martyrs, B.P. 166, F-38042, Grenoble Cedex 09, France
1 shared publication- Aleandro Diana
Department of Chemistry, University of Turin, 10125 Turin, Italy
1 shared publication C. Peroz
CRETA, BP166, 38042 Grenoble Cedex 09, France
1 shared publication- Casamassa
Italian National Research Council, ICMATE, Via De Marini 6, 16149, Genova, Italy
1 shared publication
Latest Publications
- Open Access
- 11 April 2026
- Published by Elsevier in SSRN Electronic Journal
A screening framework for brake materials: friction–wear performance and multi-element PM10 fingerprinting
Here we propose a screening framework that couples controlled pin-on-disc tribology with multi-element PM10 fingerprinting to benchmark brake material pairs. Industrially inspired pad materials representing one non-asbestos organic (NAO) and two low-steel (LS) classes were produced and tested against grey cast iron (GCI) disc and three coated discs. Friction, pin and disc wear, and particle number/mass size distributions were monitored in a closed Pin on Disc chamber using FMPS and ELPI+, while PM10 was collected on PTFE filters. A microwave-assisted digestion protocol (HNO₃/H₂O₂/HBF₄) was validated using SRM NIST 1648a enabling ICP-OES/ICP-MS determination of 29 elements in the collected PM10. The inorganic chemical composition of emitted PM10 was analysed to compare it with the starting friction materials composition. Chemical analysis allowed a comparison of different tribological pairs by evaluating tribological performance, wear, and the existence of correlations between the chemical composition of the PM10 emitted and the starting materials (disc and pad). FESEM analysis coupled with EDX provided morphological and chemical characterisation. Overall, the study shows that simplified formulations, combined with validated multi-element PM10 analysis, offer a practical route to screen disc coatings and pad ingredients and guide materials selection under controlled sliding conditions aiming to address the future development of brake material formulations optimized for performance, durability, and minimal environmental impact.
- 11 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA screening framework for brake materials: friction–wear performance and multi-element PM10 fingerprinting
Here we propose a screening framework that couples controlled pin-on-disc tribology with multi-element PM10 fingerprinting to benchmark brake material pairs. Industrially inspired pad materials representing one non-asbestos organic (NAO) and two low-steel (LS) classes were produced and tested against grey cast iron (GCI) disc and three coated discs. Friction, pin and disc wear, and particle number/mass size distributions were monitored in a closed Pin on Disc chamber using FMPS and ELPI+, while PM10 was collected on PTFE filters. A microwave-assisted digestion protocol (HNO₃/H₂O₂/HBF₄) was validated using SRM NIST 1648a enabling ICP-OES/ICP-MS determination of 29 elements in the collected PM10. The inorganic chemical composition of emitted PM10 was analysed to compare it with the starting friction materials composition. Chemical analysis allowed a comparison of different tribological pairs by evaluating tribological performance, wear, and the existence of correlations between the chemical composition of the PM10 emitted and the starting materials (disc and pad). FESEM analysis coupled with EDX provided morphological and chemical characterisation. Overall, the study shows that simplified formulations, combined with validated multi-element PM10 analysis, offer a practical route to screen disc coatings and pad ingredients and guide materials selection under controlled sliding conditions aiming to address the future development of brake material formulations optimized for performance, durability, and minimal environmental impact.
- Open Access
- 1 June 2021
- Published by Elsevier in Open Ceramics
- Vol. 6, 100128
Granular and platelet titanate as promising brake pads ingredients
- 1 June 2021
- Published by Elsevier in Open Ceramics
- Vol. 6, 100128
Open AccessGranular and platelet titanate as promising brake pads ingredients
- 1 April 2003
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 386, 296-299
Epitaxial thick film of YBCO by high temperature spray pyrolysis for coated conductors
- 1 April 2003
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 386, 296-299
Epitaxial thick film of YBCO by high temperature spray pyrolysis for coated conductors
- 1 November 2001
- Published by Elsevier in Journal of Solid State Chemistry
- Vol. 161 (2) , 355-364
Structural and Superconducting Properties of Hg0.75Re0.25Ba2−xSrxCa2Cu3O8+δ Superconductors Grown by Sol–Gel and Sealed Quartz Tube Synthesis
- 1 November 2001
- Published by Elsevier in Journal of Solid State Chemistry
- Vol. 161 (2) , 355-364
Structural and Superconducting Properties of Hg0.75Re0.25Ba2−xSrxCa2Cu3O8+δ Superconductors Grown by Sol–Gel and Sealed Quartz Tube Synthesis
- 25 September 2001
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 14 (10) , 875-879
Hg-based cuprate superconducting thin films prepared on CeO2buffered R-plane sapphire substrate
Hg-Ba-Ca-Cu-O films have been grown on CeO2/R-plane sapphire substrates using a two-step process. First, a 200 nm thick Ba-Ca-Cu-(O, F) precursor film was prepared by sequential evaporation, then Hg-Re-Ba-Ca-Cu-O pellets as a source of Hg-vapour were applied using heat treatment. The prepared films were continuous with sufficient adhesion to the substrate and a maximum zero-resistance critical temperature of TC0 = 118 K. The x-ray diffraction measurements of all the prepared films confirmed the Hg-1212 phase as well as the minor Hg-1223 phase in some cases. We found that the best results were obtained at the mercuration temperature of 775 °C and an optimal annealing time within the range 0.5-5 h. The superconducting properties of the films prepared under unsuitable conditions were mostly improved after annealing in oxygen atmosphere. Darker parts of the film exhibited a different surface morphology and the presence of the Hg-1223 phase in plate-like grains.
- 25 September 2001
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 14 (10) , 875-879
Hg-based cuprate superconducting thin films prepared on CeO2buffered R-plane sapphire substrate
Hg-Ba-Ca-Cu-O films have been grown on CeO2/R-plane sapphire substrates using a two-step process. First, a 200 nm thick Ba-Ca-Cu-(O, F) precursor film was prepared by sequential evaporation, then Hg-Re-Ba-Ca-Cu-O pellets as a source of Hg-vapour were applied using heat treatment. The prepared films were continuous with sufficient adhesion to the substrate and a maximum zero-resistance critical temperature of TC0 = 118 K. The x-ray diffraction measurements of all the prepared films confirmed the Hg-1212 phase as well as the minor Hg-1223 phase in some cases. We found that the best results were obtained at the mercuration temperature of 775 °C and an optimal annealing time within the range 0.5-5 h. The superconducting properties of the films prepared under unsuitable conditions were mostly improved after annealing in oxygen atmosphere. Darker parts of the film exhibited a different surface morphology and the presence of the Hg-1223 phase in plate-like grains.