Elaine Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Elaine Liu has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Abilyn McConnell1 shared publication
- Alexander Hanss
Institute of Innovative Mobility, Technische Hochschule Ingolstadt, Ingolstadt, Germany
1 shared publication - Barbara Simpson
Stanford University
1 shared publication Bret Bosma
1 shared publicationBryson Robertson
1 shared publication- Gordon Elger
Institute for Innovative Mobility, Technische Hochschule Ingolstadt
1 shared publication
Latest Publications
- 15 June 2026
- Published by Elsevier in Ocean Engineering
- Vol. 362
Development of a real-time hybrid simulation framework for wave energy converter mooring applications
- 15 June 2026
- Published by Elsevier in Ocean Engineering
- Vol. 362
Development of a real-time hybrid simulation framework for wave energy converter mooring applications
- 1 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Failure Identification in LED packages by Transient Thermal Analysis and Calibrated FE Models
Transient thermal analysis (TTA) by experimental thermal impedance (Zth) measurements and data simulation by transient finite element (FE) simulation are suited to investigate the thermal path and mechanical integrity of electronic devices. After calibration, the FE model can be used for failure mode analysis. In this paper first a FE model for blue Flip Chip (FC) LEDs is set-up and calibrated to the experimental data. To reduce the ambiguity of the parameter identification within the calibration process caused by the relative large number of model parameters in a transient FE simulation several sets of experimental data are measured and simulated: the LED assembled on different substrates, i.e. an AlN ceramic and a standard Al-IMS board, and similar LEDs, i.e. same LED type but different sized light emitting area (1 mm 2 and 0.5 mm 2 ). The model is calibrated in the time domain using b(z), i.e. the logarithmic time derived of Zth(z= ln(t)). The least square residuum of simulated and experimental data is minimized. Different approaches of fitting are compared, i.e. fitting b(z), Zth(t) and the structure function, resulting in b(z) being a good option for the LED under investigation. The calibration is obtained by an optimizer in an automated workflow, i.e. using ANSYS coupled with optiSLang.After calibration the model is used to identify failures during accelerated stress test. An automatic TTA tester is used to detect changes of the Z th (t) during accelerated lifetime testing, e.g. temperature shock testing.By implementing failure into the calibrated model, e.g. cracks in the solder joint, delamination of the EPI from the redistribution layer and degradation of the dielectric layer of the Al-IMS, the calibrated model is fitted to the b(z) curves of the aged samples. The strength of the approach is demonstrated by extracting the quantitative changes of the physical parameters from the fitted model in an automatic way.
- 1 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Failure Identification in LED packages by Transient Thermal Analysis and Calibrated FE Models
Transient thermal analysis (TTA) by experimental thermal impedance (Zth) measurements and data simulation by transient finite element (FE) simulation are suited to investigate the thermal path and mechanical integrity of electronic devices. After calibration, the FE model can be used for failure mode analysis. In this paper first a FE model for blue Flip Chip (FC) LEDs is set-up and calibrated to the experimental data. To reduce the ambiguity of the parameter identification within the calibration process caused by the relative large number of model parameters in a transient FE simulation several sets of experimental data are measured and simulated: the LED assembled on different substrates, i.e. an AlN ceramic and a standard Al-IMS board, and similar LEDs, i.e. same LED type but different sized light emitting area (1 mm 2 and 0.5 mm 2 ). The model is calibrated in the time domain using b(z), i.e. the logarithmic time derived of Zth(z= ln(t)). The least square residuum of simulated and experimental data is minimized. Different approaches of fitting are compared, i.e. fitting b(z), Zth(t) and the structure function, resulting in b(z) being a good option for the LED under investigation. The calibration is obtained by an optimizer in an automated workflow, i.e. using ANSYS coupled with optiSLang.After calibration the model is used to identify failures during accelerated stress test. An automatic TTA tester is used to detect changes of the Z th (t) during accelerated lifetime testing, e.g. temperature shock testing.By implementing failure into the calibrated model, e.g. cracks in the solder joint, delamination of the EPI from the redistribution layer and degradation of the dielectric layer of the Al-IMS, the calibrated model is fitted to the b(z) curves of the aged samples. The strength of the approach is demonstrated by extracting the quantitative changes of the physical parameters from the fitted model in an automatic way.