Martha Elva Pérez Ramos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Martha Elva Pérez Ramos has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Edain Belén Pérez Mendoza
Campus Querétaro, Tecnológico de Monterrey, Epigmenio González 500, Fracc. San Pablo, Santiago de Querétaro 76130, Querétaro, Mexico
1 shared publication - José de Jesús Pérez Bueno
Centro de Investigación y Desarrollo Tecnológico en Electroquímica, S.C., Parque Tecnológico Sanfandila, Pedro Escobedo 76703, Querétaro, Mexico
1 shared publication - Ma. Guadalupe Plaza
Tecnológico Nacional de México, Instituto Tecnológico de Querétaro, Av. Tecnológico s/n Esq. M. Escobedo Col. Centro, Santiago de Querétaro 76000, Querétaro, Mexico
1 shared publication - Maria Luisa Mendoza López
Tecnológico Nacional de México, Instituto Tecnológico de Querétaro, Av. Tecnológico s/n Esq. M. Escobedo Col. Centro, Santiago de Querétaro 76000, Qro, Mexico
1 shared publication
Latest Publications
- Open Access
The Use of Fresnel Lens Softening Stations to Improve Recycling Feasibility of Injection-Molding Purges
Injection-molding purges are heterogeneous, bulky residues whose uncertain composition and irregular geometry hinder direct reinsertion, making cold shredding costly and maintenance-intensive. This work develops a low-infrastructure solar-assisted pre-processing route using a PMMA Fresnel lens to induce controlled sub-onset softening and enable clean shear cutting without destructive thermal histories. The sub-onset softening is here defined into a viscoelastically active range (at or above Tg for the amorphous phase) while remaining below the melting onset (Tm, onset) and below the onset of thermal degradation (Td, onset). The station was engineered via QFD and risk-oriented design tools, while a weighted Pugh matrix selected shear cutting over saw-based alternatives. A screening factorial DOE showed that lens height, angle, and their interaction significantly govern focal-spot diameter and receiver temperature, yielding linear relations for conservative set-point selection. Receiver benchmarking further indicated that copper reaches substantially higher temperatures than graphite under identical exposure conditions, supporting copper as the simplest, rapid-heating receiver. Under DOE-calibrated operation, tear-free shear cutting was achieved across representative purge families (PP–ABS, PC–ABS–PP, PA66, PA66-filler, and POM) without forced convection. From a recycling and waste-management perspective, the approach converts bulky purge scrap into mill-compatible feedstock with reduced mechanical resistance, lowering tool wear and fines generation, accelerating downsizing, and limiting stockpiling that elevates combustible-inventory fire risk. Overall, the proposed DOE-calibrated, operator-friendly framework improves recycling feasibility by enabling safer handling, more stable preprocessing throughput, and reduced reliance on disposal or long-term storage for heterogeneous industrial purges.
Open AccessThe Use of Fresnel Lens Softening Stations to Improve Recycling Feasibility of Injection-Molding Purges
Injection-molding purges are heterogeneous, bulky residues whose uncertain composition and irregular geometry hinder direct reinsertion, making cold shredding costly and maintenance-intensive. This work develops a low-infrastructure solar-assisted pre-processing route using a PMMA Fresnel lens to induce controlled sub-onset softening and enable clean shear cutting without destructive thermal histories. The sub-onset softening is here defined into a viscoelastically active range (at or above Tg for the amorphous phase) while remaining below the melting onset (Tm, onset) and below the onset of thermal degradation (Td, onset). The station was engineered via QFD and risk-oriented design tools, while a weighted Pugh matrix selected shear cutting over saw-based alternatives. A screening factorial DOE showed that lens height, angle, and their interaction significantly govern focal-spot diameter and receiver temperature, yielding linear relations for conservative set-point selection. Receiver benchmarking further indicated that copper reaches substantially higher temperatures than graphite under identical exposure conditions, supporting copper as the simplest, rapid-heating receiver. Under DOE-calibrated operation, tear-free shear cutting was achieved across representative purge families (PP–ABS, PC–ABS–PP, PA66, PA66-filler, and POM) without forced convection. From a recycling and waste-management perspective, the approach converts bulky purge scrap into mill-compatible feedstock with reduced mechanical resistance, lowering tool wear and fines generation, accelerating downsizing, and limiting stockpiling that elevates combustible-inventory fire risk. Overall, the proposed DOE-calibrated, operator-friendly framework improves recycling feasibility by enabling safer handling, more stable preprocessing throughput, and reduced reliance on disposal or long-term storage for heterogeneous industrial purges.