Ruizhe Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ruizhe Li has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Bo Gao
School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044, China
2 shared publications - Hanzhi Yao
School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044, China
2 shared publications - Qiuying Chang
School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044, China
2 shared publications - Zhongnan Wang
School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044, China
2 shared publications - Bin Wang
School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044, China
1 shared publication - Pengpeng Bai
State Key Laboratory of Tribology in Advanced Equipment, Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China
1 shared publication
Latest Publications
- Open Access
- 10 April 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (4) , 162
Picosecond Laser Surface Texturing on Copper Substrates: Boosting Interfacial Adhesion and Tribological Performance of Magnesium Silicate Hydroxide-Based Solid Lubricant Coatings
Metal substrates were preprocessed via picosecond laser surface texturing (PLST, 532 nm) to fabricate interfacial microgrooves for tribological performance optimization prior to deposition of a magnesium silicate hydroxide (MSH)/graphite/MoS2–PI solid lubricant coating. By tuning the PLST parameters (average laser power: 0.2–0.5 W, scan passes: 3–5, hatch spacing: 0.005–0.1 mm), three representative texture geometries (linear, circular, and square) were produced, and the resulting coating performance was compared with conventional mechanical polishing and sandblasting pretreatments. Among the three laser textures, the linear texture exhibited the most excellent tribological performance and interfacial adhesion, outperforming the circular and square counterparts. Ball-on-disk tests in a kerosene-contaminated environment (10 N, 800 rpm) showed that the linear-textured sample reached the lowest steady-state friction coefficient (0.038), lower than polished (0.048) and sandblasted (0.052) controls, together with reduced wear scar dimensions. Progressive-load scratch tests indicated a pronounced adhesion enhancement, with the critical failure load increasing from 7.05 N (polished) to 26.05 N for the linear-textured interface, which is higher than 21.21 N (circular) and 23.78 N (square) textures. Cross-sectional microscopy and EDS mapping reveal that the laser-defined microgrooves (~15 μm depth, ~120 μm width, ~500 μm spacing) act as a parameter-controlled interfacial architecture that promotes mechanical interlocking and provides lubricant-rich reservoirs. This laser-enabled interfacial design suppresses delamination, supports transfer film stability, and ultimately enhances the coating’s tribological performance by reducing friction and wear.
- 10 April 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (4) , 162
Open AccessPicosecond Laser Surface Texturing on Copper Substrates: Boosting Interfacial Adhesion and Tribological Performance of Magnesium Silicate Hydroxide-Based Solid Lubricant Coatings
Metal substrates were preprocessed via picosecond laser surface texturing (PLST, 532 nm) to fabricate interfacial microgrooves for tribological performance optimization prior to deposition of a magnesium silicate hydroxide (MSH)/graphite/MoS2–PI solid lubricant coating. By tuning the PLST parameters (average laser power: 0.2–0.5 W, scan passes: 3–5, hatch spacing: 0.005–0.1 mm), three representative texture geometries (linear, circular, and square) were produced, and the resulting coating performance was compared with conventional mechanical polishing and sandblasting pretreatments. Among the three laser textures, the linear texture exhibited the most excellent tribological performance and interfacial adhesion, outperforming the circular and square counterparts. Ball-on-disk tests in a kerosene-contaminated environment (10 N, 800 rpm) showed that the linear-textured sample reached the lowest steady-state friction coefficient (0.038), lower than polished (0.048) and sandblasted (0.052) controls, together with reduced wear scar dimensions. Progressive-load scratch tests indicated a pronounced adhesion enhancement, with the critical failure load increasing from 7.05 N (polished) to 26.05 N for the linear-textured interface, which is higher than 21.21 N (circular) and 23.78 N (square) textures. Cross-sectional microscopy and EDS mapping reveal that the laser-defined microgrooves (~15 μm depth, ~120 μm width, ~500 μm spacing) act as a parameter-controlled interfacial architecture that promotes mechanical interlocking and provides lubricant-rich reservoirs. This laser-enabled interfacial design suppresses delamination, supports transfer film stability, and ultimately enhances the coating’s tribological performance by reducing friction and wear.
- Open Access
- 6 March 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (3) , 114
Study on the Synergistic Lubrication Mechanism of Nickel and Magnesium Silicate Hydroxide in Molybdenum Disulfide-Based Composite Coatings
Molybdenum disulfide (MoS2)-based composite systems are widely used as solid lubricating coatings. However, further optimization towards lower friction and higher wear resistance remains necessary to meet the extreme operating conditions and high reliability requirements of next-generation aerospace equipment. This study investigated the tribological performance of MoS2/epoxy composite coatings by comparing the effects of individual and combined additions of nano nickel (Ni) and magnesium silicate hydroxide (MSH). The coating preparation process adopted in this study is the bonding method. Experimental results showed that, under a load of 2 N and a rotational speed of 500 r/min, the coating containing 0.3 g Ni and 0.1 g MSH (labeled W03Ni01MSH) achieved a 22% reduction in wear scar width compared to the coating with only Ni, demonstrating a distinct synergistic effect. This is attributed to the complementary roles of the two additives: Ni promotes the formation of flaky wear debris, facilitating rapid formation and stabilization of a transfer film, thereby reducing friction; MSH enhances the load carrying capacity of the coating and suppresses wear propagation, thereby improving wear resistance. Furthermore, this composite coating exhibited optimal performance under the conditions of 500 r/min and 2 N. The results of this study significantly improved the friction-reducing and wear-resistant properties of the MoS2/epoxy composite coating. This provides a new strategy for the formulation design of high-performance solid lubricating coatings.
- 6 March 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (3) , 114
Open AccessStudy on the Synergistic Lubrication Mechanism of Nickel and Magnesium Silicate Hydroxide in Molybdenum Disulfide-Based Composite Coatings
Molybdenum disulfide (MoS2)-based composite systems are widely used as solid lubricating coatings. However, further optimization towards lower friction and higher wear resistance remains necessary to meet the extreme operating conditions and high reliability requirements of next-generation aerospace equipment. This study investigated the tribological performance of MoS2/epoxy composite coatings by comparing the effects of individual and combined additions of nano nickel (Ni) and magnesium silicate hydroxide (MSH). The coating preparation process adopted in this study is the bonding method. Experimental results showed that, under a load of 2 N and a rotational speed of 500 r/min, the coating containing 0.3 g Ni and 0.1 g MSH (labeled W03Ni01MSH) achieved a 22% reduction in wear scar width compared to the coating with only Ni, demonstrating a distinct synergistic effect. This is attributed to the complementary roles of the two additives: Ni promotes the formation of flaky wear debris, facilitating rapid formation and stabilization of a transfer film, thereby reducing friction; MSH enhances the load carrying capacity of the coating and suppresses wear propagation, thereby improving wear resistance. Furthermore, this composite coating exhibited optimal performance under the conditions of 500 r/min and 2 N. The results of this study significantly improved the friction-reducing and wear-resistant properties of the MoS2/epoxy composite coating. This provides a new strategy for the formulation design of high-performance solid lubricating coatings.