Ahmed Sadaqa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ahmed Sadaqa has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Bruno da Silva
Department of Electronics and Informatics, Vrije Universiteit Brussel, 1050 Brussels, Belgium
3 shared publications - Han Bao
Department of Electronic and Information, Vrije Universiteit Brussel, Brussels, Belgium
2 shared publications - Ming Ling
Southeast University, Nanjing, China
2 shared publications - Ruiqi Chen
Department of Electronics and Informatics, Vrije Universiteit Brussel, Brussels, Belgium
2 shared publications - Shidi Tang
Southeast University
2 shared publications - Abdessamad Nassihi
Department of Electronics and Informatics (ETRO), Vrije Universiteit Brussel (VUB), 1050 Brussels, Belgium
1 shared publication
Latest Publications
- 4 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 34 (6) , 2015-2019
FANE: FPGA-Based FP8 Approximate Neural Network Engine
The 8-bit floating-point (FP8) format has gained growing interest in neural networks (NNs) for its superior dynamic range over traditional INT8. However, multiply-accumulate (MAC) operations remain a major source of power consumption during inference of NNs, which makes DSP-free design important, especially for edge FPGAs with few or no DSPs. Therefore, this brief presents FPGA-based FP8 approximate neural network engine (FANE), an FPGA-based approximate NN engine for FP8. We first introduce a novel approximation method that replaces the multiplications by linear additions. This approximate method reduces power consumption while maintaining high accuracy, outperforming the latest FP8 approximate multiplier by 53.15%. Based on this design, we construct an FP8 MAC unit and integrate it into both a convolution engine and a matrix–vector multiplication (MVM) unit. Finally, we integrate our design into a large language model (LLM). The result shows 61.5% higher efficiency (TOPS/W) than the previous design, demonstrating the superiority of FANE in terms of performance and power efficiency. The code of FANE is available on our https://github.com/hanbao04/FANE-FPGA-based-FP8-Approximate-Neural-Network-Engine.git
- 4 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 34 (6) , 2015-2019
FANE: FPGA-Based FP8 Approximate Neural Network Engine
The 8-bit floating-point (FP8) format has gained growing interest in neural networks (NNs) for its superior dynamic range over traditional INT8. However, multiply-accumulate (MAC) operations remain a major source of power consumption during inference of NNs, which makes DSP-free design important, especially for edge FPGAs with few or no DSPs. Therefore, this brief presents FPGA-based FP8 approximate neural network engine (FANE), an FPGA-based approximate NN engine for FP8. We first introduce a novel approximation method that replaces the multiplications by linear additions. This approximate method reduces power consumption while maintaining high accuracy, outperforming the latest FP8 approximate multiplier by 53.15%. Based on this design, we construct an FP8 MAC unit and integrate it into both a convolution engine and a matrix–vector multiplication (MVM) unit. Finally, we integrate our design into a large language model (LLM). The result shows 61.5% higher efficiency (TOPS/W) than the previous design, demonstrating the superiority of FANE in terms of performance and power efficiency. The code of FANE is available on our https://github.com/hanbao04/FANE-FPGA-based-FP8-Approximate-Neural-Network-Engine.git
- Open Access
- 10 March 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (6) , 2648
Exploiting Low-Power Techniques of a Flash-Based SoC FPGA for Energy-Efficient Edge Processing
Battery-powered edge systems must operate under tight energy budgets while facing growing computational demand from rapidly evolving edge workloads. Field-programmable gate arrays (FPGAs) offer middle ground when optimized for energy, especially flash-based FPGAs due to inherent low-power characteristics. Microchip flash-based SoC FPGAs further expose ultra-low-power (LP) modes including fabric Flash*Freeze (F*F), processor sleep and selectable standby clocks. Combining these modes with HW/SW partitioning and clock-frequency scaling can reduce energy for low-duty-cycle workloads; however, selecting an energy-efficient operating point in this multidimensional design space is non-trivial. This work explores the design space by measuring and analyzing LP modes across three architectural approaches (SW, co-design, and HW) under frequency scaling on a Microchip Smartfusion2 platform, using a low-duty-cycle heart-rate monitoring workload. Measurements indicate that, for low-duty-cycle workloads, total energy is dominated by the idle phase and is minimized by combining fabric-F*F with processor sleep. The results further show that main-clock downscaling reduces active-phase current but has limited impact on idle consumption once F*F and sleep are applied, while standby-clock selection trades idle current against LP entry/exit latency. Event-rate scaling further shows that the energy-optimal operating point can shift with duty cycle. We provide measurement-based guidelines for duty-cycle-aware energy-efficient operating point selection in similar flash-based SoC platforms.
- 10 March 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (6) , 2648
Open AccessExploiting Low-Power Techniques of a Flash-Based SoC FPGA for Energy-Efficient Edge Processing
Battery-powered edge systems must operate under tight energy budgets while facing growing computational demand from rapidly evolving edge workloads. Field-programmable gate arrays (FPGAs) offer middle ground when optimized for energy, especially flash-based FPGAs due to inherent low-power characteristics. Microchip flash-based SoC FPGAs further expose ultra-low-power (LP) modes including fabric Flash*Freeze (F*F), processor sleep and selectable standby clocks. Combining these modes with HW/SW partitioning and clock-frequency scaling can reduce energy for low-duty-cycle workloads; however, selecting an energy-efficient operating point in this multidimensional design space is non-trivial. This work explores the design space by measuring and analyzing LP modes across three architectural approaches (SW, co-design, and HW) under frequency scaling on a Microchip Smartfusion2 platform, using a low-duty-cycle heart-rate monitoring workload. Measurements indicate that, for low-duty-cycle workloads, total energy is dominated by the idle phase and is minimized by combining fabric-F*F with processor sleep. The results further show that main-clock downscaling reduces active-phase current but has limited impact on idle consumption once F*F and sleep are applied, while standby-clock selection trades idle current against LP entry/exit latency. Event-rate scaling further shows that the energy-optimal operating point can shift with duty cycle. We provide measurement-based guidelines for duty-cycle-aware energy-efficient operating point selection in similar flash-based SoC platforms.
- 6 March 2026
- Published by Elsevier in Integration
- Vol. 109
BenDan: Benchmarking DPU performance on FPGAs
- 6 March 2026
- Published by Elsevier in Integration
- Vol. 109
BenDan: Benchmarking DPU performance on FPGAs