Abhishek Raj
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Abhishek Raj has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
Avneesh Anshul
CSIR-National Environmental Engineering Research Institute (NEERI), Nagpur, India
24 shared publicationsManish Kumar
18 shared publications- Manish Kumar
Experimental Research Laboratory, Department of Physics, ARSD College, University of Delhi, New Delhi, India
15 shared publications Arvind Kumar
9 shared publications- Avneesh Anshul
CSIR-National Environmental Engineering Research Institute (CSIR-NEERI)
6 shared publications Ankit Gupta
Academy of Scientific and Innovative Research (AcSIR), Ghaziabad 201002, India
4 shared publications
Latest Publications
- 26 October 2026
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 237 (24) , 1425
Evaluation of CO2 Sequestration Capacity of Red Mud Under Controlled Solid–Gas Reaction Conditions
- 26 October 2026
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 237 (24) , 1425
Evaluation of CO2 Sequestration Capacity of Red Mud Under Controlled Solid–Gas Reaction Conditions
- 28 August 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (11) , 9380-9395
Energy Band Alignment and Interface Defect Optimization in 2D Dion–Jacobson PeDAMA5Pb6I19/3D-CsGeI3 Bilayer Perovskite Solar Cells: A Numerical Study
- 28 August 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (11) , 9380-9395
Energy Band Alignment and Interface Defect Optimization in 2D Dion–Jacobson PeDAMA5Pb6I19/3D-CsGeI3 Bilayer Perovskite Solar Cells: A Numerical Study
- 1 November 2025
- Published by Springer Nature
- p. 399-406
Perovskite Solar Cells: Summary and Future Directions
- 1 November 2025
- Published by Springer Nature
- p. 399-406
Perovskite Solar Cells: Summary and Future Directions
- 1 November 2025
- Published by Springer Nature
- p. 1-19
Introduction: An Overview of Perovskite Solar Cells
- 1 November 2025
- Published by Springer Nature
- p. 1-19
Introduction: An Overview of Perovskite Solar Cells
- Open Access
- 25 September 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-19
Physical parameter optimization and band alignment approach for efficiency improvement in Cs2AgBiBr6 based lead-free perovskite solar cells
In recent years, organic-inorganic halide perovskite solar cells (PSCs) have garnered significant global attention due to their exceptional performance and high-power conversion efficiency (PCE). The impressive device capabilities have encouraged extensive research into various advanced engineering strategies aimed at improving the physical characteristics of PSCs. Nevertheless, while lead-based PSCs have achieved outstanding PCEs, concerns regarding lead toxicity and long-term stability hinder their commercial viability. Besides, an appropriate hole transport material is also required to reduce the recombination losses at interfaces. In the present study, PSCs were designed in SCAPS simulation software with cell configuration of FTO/TiO2/Cs2AgBiBr6/HTLs (CuI, CuSCN, Cu2O, Spiro-OMeTAD)/Au. Here, lead-free stable double perovskite material Cs2AgBiBr6 is used as light absorbing material and TiO2 electron transport material. However, device response of PSCs is studied with different hole transport materials. With optimization of defects, and thickness of perovskite absorber, along with operating temperature and series resistance, Cu2O as hole transport layer (HTL) based PSCs have achieved open-circuit voltage (VOC) of 1.33 V, current density of (JSC) of 8.78 mA/cm2, fill factor (FF) of 64.96%, and PCE of 7.60%. The reason behind the variation in device performance was realised using capacitance-voltage (C-V), conductance-voltage (G-V), capacitance – frequency (C-f) and, conductance-frequency (G-f) analysis. It has been found that Cu2O HTL-based PSCs exhibited reduced defects at the interfacial region, attributed to the appropriate band alignment with the Cs2AgBiBr6 perovskite absorber. The suggested simulation study may contribute significantly to the advancement of lead-free all-inorganic PSCs, aiming for improved efficiency.
- 25 September 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-19
Open AccessPhysical parameter optimization and band alignment approach for efficiency improvement in Cs2AgBiBr6 based lead-free perovskite solar cells
In recent years, organic-inorganic halide perovskite solar cells (PSCs) have garnered significant global attention due to their exceptional performance and high-power conversion efficiency (PCE). The impressive device capabilities have encouraged extensive research into various advanced engineering strategies aimed at improving the physical characteristics of PSCs. Nevertheless, while lead-based PSCs have achieved outstanding PCEs, concerns regarding lead toxicity and long-term stability hinder their commercial viability. Besides, an appropriate hole transport material is also required to reduce the recombination losses at interfaces. In the present study, PSCs were designed in SCAPS simulation software with cell configuration of FTO/TiO2/Cs2AgBiBr6/HTLs (CuI, CuSCN, Cu2O, Spiro-OMeTAD)/Au. Here, lead-free stable double perovskite material Cs2AgBiBr6 is used as light absorbing material and TiO2 electron transport material. However, device response of PSCs is studied with different hole transport materials. With optimization of defects, and thickness of perovskite absorber, along with operating temperature and series resistance, Cu2O as hole transport layer (HTL) based PSCs have achieved open-circuit voltage (VOC) of 1.33 V, current density of (JSC) of 8.78 mA/cm2, fill factor (FF) of 64.96%, and PCE of 7.60%. The reason behind the variation in device performance was realised using capacitance-voltage (C-V), conductance-voltage (G-V), capacitance – frequency (C-f) and, conductance-frequency (G-f) analysis. It has been found that Cu2O HTL-based PSCs exhibited reduced defects at the interfacial region, attributed to the appropriate band alignment with the Cs2AgBiBr6 perovskite absorber. The suggested simulation study may contribute significantly to the advancement of lead-free all-inorganic PSCs, aiming for improved efficiency.
- 1 August 2025
- Published by Springer Nature
- p. 105-121
Potential Applications of Spinel Nano-Ferrites in Humidity Sensors
- 1 August 2025
- Published by Springer Nature
- p. 105-121
Potential Applications of Spinel Nano-Ferrites in Humidity Sensors
- 15 November 2023
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 673
Photovoltaic energy conversion in multiferroic perovskite absorber-based devices via experiment and theoretical calculations
- 15 November 2023
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 673
Photovoltaic energy conversion in multiferroic perovskite absorber-based devices via experiment and theoretical calculations