Yongyong Li
Research Subjects
Yongyong Li has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Zhenbao Li
Institute of Engineering Technology, PetroChina Western Drilling Engineering Co., Ltd., Karamay 834000, China
4 shared publications - Chengpeng Yu
School of Mechanical Engineering, Yanshan University, Qinhuangdao 066004, China
2 shared publications - Hengshuo Zhang
National Research Center of Pumps, Jiangsu University, Zhenjiang 212013, China
2 shared publications - Wanlu Jiang
Hebei Provincial Key Laboratory of Heavy Machinery Fluid Power Transmission and Control, Yanshan University, Qinhuangdao 066004, China
2 shared publications - Yang Zhao
School of Mechanical Engineering, Yanshan University, Qinhuangdao 066004, China
2 shared publications - Yong Zhu
National Research Center of Pumps, Jiangsu University, Zhenjiang 212013, China
2 shared publications
Latest Publications
- Open Access
Temperature Drift Compensation for Deep-Well Drill Bit State Parameters Using Electric Eel Foraging Optimization and Physics-Informed Extreme Learning Machine
In deep and ultra-deep drilling, high downhole temperatures cause appreciable thermal drift in the strain-gauge bridge of the bit parameter recorder, degrading the measurement fidelity of weight-on-bit (WOB) and torque. This paper presents a temperature-drift compensation scheme combining electric eel foraging optimization (EEFO) with a physics-informed extreme learning machine (PIELM). Four physical priors are formulated as constraints: trend consistency and regression deviation are embedded into the output-weight solution through an augmented linear system, while proportional relationship and continuity enter the fitness function as penalty terms. EEFO performs the hyperparameter search; enhancement strategies addressing its population-diversity decay and limited final-stage accuracy are examined under an equal function-evaluation budget, and the deployed configuration is determined by the ablation evidence. Under leakage-free nested cross-validation, hyperparameter optimization reduces the WOB RMSE from 0.712 kN with fixed hyperparameters to 0.246 kN, a 2.9-fold improvement, while a ridge-regularized ELM baseline reaches 0.708 kN, indicating that the gain originates from the hyperparameter optimization itself. Equal-budget ablation on 13 classical benchmark functions ranks the dynamic-boundary quasi-opposition-based learning variant as the most effective single strategy, and the deployed configuration attains the lowest mean fitness on the target problem. Downhole evaluation is formulated as a consistency-verification framework, with no downhole load ground truth and the WOB voltage lying outside the training range. The apparent drift elimination under in-sample mapping does not survive leakage-free mapping protocols (the WOB elimination rates are 0.3%, 0.0%, and 5.1% under P2–P4) and is therefore not interpreted as a compensation-accuracy figure.
Open AccessTemperature Drift Compensation for Deep-Well Drill Bit State Parameters Using Electric Eel Foraging Optimization and Physics-Informed Extreme Learning Machine
In deep and ultra-deep drilling, high downhole temperatures cause appreciable thermal drift in the strain-gauge bridge of the bit parameter recorder, degrading the measurement fidelity of weight-on-bit (WOB) and torque. This paper presents a temperature-drift compensation scheme combining electric eel foraging optimization (EEFO) with a physics-informed extreme learning machine (PIELM). Four physical priors are formulated as constraints: trend consistency and regression deviation are embedded into the output-weight solution through an augmented linear system, while proportional relationship and continuity enter the fitness function as penalty terms. EEFO performs the hyperparameter search; enhancement strategies addressing its population-diversity decay and limited final-stage accuracy are examined under an equal function-evaluation budget, and the deployed configuration is determined by the ablation evidence. Under leakage-free nested cross-validation, hyperparameter optimization reduces the WOB RMSE from 0.712 kN with fixed hyperparameters to 0.246 kN, a 2.9-fold improvement, while a ridge-regularized ELM baseline reaches 0.708 kN, indicating that the gain originates from the hyperparameter optimization itself. Equal-budget ablation on 13 classical benchmark functions ranks the dynamic-boundary quasi-opposition-based learning variant as the most effective single strategy, and the deployed configuration attains the lowest mean fitness on the target problem. Downhole evaluation is formulated as a consistency-verification framework, with no downhole load ground truth and the WOB voltage lying outside the training range. The apparent drift elimination under in-sample mapping does not survive leakage-free mapping protocols (the WOB elimination rates are 0.3%, 0.0%, and 5.1% under P2–P4) and is therefore not interpreted as a compensation-accuracy figure.
- Open Access
- 20 August 2026
- Published by MDPI AG in Electronics
- Vol. 15 (16) , 3741
Pump Noise Suppression in Continuous-Wave Mud Pulse Telemetry via Dual-Sensor Joint Delay and Amplitude Compensation
Continuous-wave mud pulse telemetry offers high spectral efficiency and transmission rates, making it an important technology for high-speed information transmission under complex well conditions. However, surface-received signals are highly susceptible to periodic pressure pulsations generated by mud pumps, which degrade phase extraction and symbol decision performance. Dual-pressure-sensor delayed differential processing can exploit the correlated propagation characteristics of pump noise between two measurement locations to suppress its correlated components; however, its performance depends on accurately matching the propagation delay and amplitude compensation coefficient. To specifically address the dynamic variation in the pump noise propagation relationship between two measurement locations under actual operating conditions, a joint delay–amplitude compensation method is developed, in which pump noise suppression is formulated as the joint estimation of the signal propagation delay and amplitude compensation coefficient. Built upon LMS-based time delay estimation, the proposed method employs an enhanced time-varying step-size LMS time delay estimation algorithm (HTVSS-LMSTDE) to improve dynamic retracking capability following changes in propagation delay. A sliding-window weighted least-squares method (SWLS) is further introduced to estimate the amplitude compensation coefficient and correct differential mismatch caused by variations in the amplitude transfer ratio. With non-pump interference modeled as additive white Gaussian noise independent of the telemetry signal and pump noise, simulation results demonstrate that, when the propagation delay and amplitude transfer ratio vary simultaneously, the proposed method yields delay estimates and amplitude compensation coefficients close to their theoretically optimal values. Field wellbore tests further verify that the proposed method effectively attenuates low-frequency pump noise interference in continuous-wave mud pulse telemetry signals while preserving the BPSK-modulated information.
- 20 August 2026
- Published by MDPI AG in Electronics
- Vol. 15 (16) , 3741
Open AccessPump Noise Suppression in Continuous-Wave Mud Pulse Telemetry via Dual-Sensor Joint Delay and Amplitude Compensation
Continuous-wave mud pulse telemetry offers high spectral efficiency and transmission rates, making it an important technology for high-speed information transmission under complex well conditions. However, surface-received signals are highly susceptible to periodic pressure pulsations generated by mud pumps, which degrade phase extraction and symbol decision performance. Dual-pressure-sensor delayed differential processing can exploit the correlated propagation characteristics of pump noise between two measurement locations to suppress its correlated components; however, its performance depends on accurately matching the propagation delay and amplitude compensation coefficient. To specifically address the dynamic variation in the pump noise propagation relationship between two measurement locations under actual operating conditions, a joint delay–amplitude compensation method is developed, in which pump noise suppression is formulated as the joint estimation of the signal propagation delay and amplitude compensation coefficient. Built upon LMS-based time delay estimation, the proposed method employs an enhanced time-varying step-size LMS time delay estimation algorithm (HTVSS-LMSTDE) to improve dynamic retracking capability following changes in propagation delay. A sliding-window weighted least-squares method (SWLS) is further introduced to estimate the amplitude compensation coefficient and correct differential mismatch caused by variations in the amplitude transfer ratio. With non-pump interference modeled as additive white Gaussian noise independent of the telemetry signal and pump noise, simulation results demonstrate that, when the propagation delay and amplitude transfer ratio vary simultaneously, the proposed method yields delay estimates and amplitude compensation coefficients close to their theoretically optimal values. Field wellbore tests further verify that the proposed method effectively attenuates low-frequency pump noise interference in continuous-wave mud pulse telemetry signals while preserving the BPSK-modulated information.
- Open Access
- 25 March 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (4) , 398
An Intelligent Temperature Compensation Method for Pressure Sensors Under High-Temperature and High-Pressure Conditions Based on a Modified Slime Mold Algorithm
During deep and ultra-deep oil and gas drilling, downhole high-temperature and high-pressure conditions significantly affect the measurement accuracy of piezoresistive pressure sensors. To improve measurement accuracy under such extreme conditions, this study proposes an intelligent temperature compensation method based on a Modified Slime Mold Algorithm (MSMA). An experimental platform covering the full operating range of 0–175 °C and 0–170 MPa was established to acquire sensor outputs, and samples were collected at various temperature and pressure points to construct a dataset. Key parameters of the compensation model were optimized using the MSMA, enhancing the model’s fitting capability. Results indicate that, after compensation, the sensor exhibits a maximum full-scale error of 0.26% and a maximum sensitivity drift of −0.019% FS/°C, significantly reducing errors compared with traditional interpolation and polynomial fitting methods. The optimized compensation model was further deployed on an embedded hardware platform, enabling high-precision temperature compensation in an engineering context. Experimental data demonstrate that the embedded implementation maintains compensation accuracy while meeting real-time application requirements, making it suitable for downhole pressure monitoring and for output correction of other intelligent sensors operating under complex field conditions.
- 25 March 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (4) , 398
Open AccessAn Intelligent Temperature Compensation Method for Pressure Sensors Under High-Temperature and High-Pressure Conditions Based on a Modified Slime Mold Algorithm
During deep and ultra-deep oil and gas drilling, downhole high-temperature and high-pressure conditions significantly affect the measurement accuracy of piezoresistive pressure sensors. To improve measurement accuracy under such extreme conditions, this study proposes an intelligent temperature compensation method based on a Modified Slime Mold Algorithm (MSMA). An experimental platform covering the full operating range of 0–175 °C and 0–170 MPa was established to acquire sensor outputs, and samples were collected at various temperature and pressure points to construct a dataset. Key parameters of the compensation model were optimized using the MSMA, enhancing the model’s fitting capability. Results indicate that, after compensation, the sensor exhibits a maximum full-scale error of 0.26% and a maximum sensitivity drift of −0.019% FS/°C, significantly reducing errors compared with traditional interpolation and polynomial fitting methods. The optimized compensation model was further deployed on an embedded hardware platform, enabling high-precision temperature compensation in an engineering context. Experimental data demonstrate that the embedded implementation maintains compensation accuracy while meeting real-time application requirements, making it suitable for downhole pressure monitoring and for output correction of other intelligent sensors operating under complex field conditions.
- Open Access
A Temperature Compensation Method for the Bit Parameter Recorder in High-Temperature Deep Wells Based on Thermo-Mechanical Coupling
Measurement While Drilling (MWD) tools are widely employed in deep and ultra-deep well drilling. In the high-temperature and high-pressure (HTHP) environments characteristic of these wells, structural deformation induced by thermal expansion interferes with the bit parameter recorder’s sensor readings, thereby degrading the measurement accuracy of weight on bit (WOB) and working torque (WT). To address this issue, this paper proposes a temperature compensation method based on thermo-mechanical coupling simulation. This method systematically establishes the quantitative relationships between multiple loads—including WT, WOB, temperature, and make-up torque—and the strain at critical locations of the bit parameter recorder through finite element analysis (FEA). Furthermore, surface calibration experiments have verified a strong linear correlation between the strain gauge voltage signals and the simulated strain. Building upon this foundation, an inversion-based compensation algorithm is developed. This algorithm effectively isolates the interference caused by thermally induced deformation and inversely deduces the true WOB and torque values by utilizing downhole-measured sensor voltage and temperature data. The research results demonstrate that the proposed temperature compensation method significantly improves the measurement accuracy of the bit parameter recorder under harsh, high-temperature operating conditions. The relative errors for both WOB and torque measurements are controlled to within 5%, providing a reliable solution for precise parameter measurement in high-temperature deep wells.
Open AccessA Temperature Compensation Method for the Bit Parameter Recorder in High-Temperature Deep Wells Based on Thermo-Mechanical Coupling
Measurement While Drilling (MWD) tools are widely employed in deep and ultra-deep well drilling. In the high-temperature and high-pressure (HTHP) environments characteristic of these wells, structural deformation induced by thermal expansion interferes with the bit parameter recorder’s sensor readings, thereby degrading the measurement accuracy of weight on bit (WOB) and working torque (WT). To address this issue, this paper proposes a temperature compensation method based on thermo-mechanical coupling simulation. This method systematically establishes the quantitative relationships between multiple loads—including WT, WOB, temperature, and make-up torque—and the strain at critical locations of the bit parameter recorder through finite element analysis (FEA). Furthermore, surface calibration experiments have verified a strong linear correlation between the strain gauge voltage signals and the simulated strain. Building upon this foundation, an inversion-based compensation algorithm is developed. This algorithm effectively isolates the interference caused by thermally induced deformation and inversely deduces the true WOB and torque values by utilizing downhole-measured sensor voltage and temperature data. The research results demonstrate that the proposed temperature compensation method significantly improves the measurement accuracy of the bit parameter recorder under harsh, high-temperature operating conditions. The relative errors for both WOB and torque measurements are controlled to within 5%, providing a reliable solution for precise parameter measurement in high-temperature deep wells.