Amir Pourjafar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Amir Pourjafar has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Albert These
Institute of Materials for Electronics and Energy Technology (i-MEET), Friedrich-Alexander-Universität Erlangen-Nürnberg, Martensstrasse 7, 91058 Erlangen, Germany
1 shared publication Anant Rastogi
Center Nanoelectronic Technologies Fraunhofer IPMS Dresden Saxony Germany
1 shared publication- Andres Osvet
Institute of Materials for Electronics and Energy Technology (i-MEET), Friedrich-Alexander-Universität Erlangen-Nürnberg, Martensstrasse 7, 91058 Erlangen, Germany
1 shared publication Ayse Sünbül
Center Nanoelectronic Technologies Fraunhofer IPMS Dresden Saxony Germany
1 shared publication- Christian Schulbert
GeoZentrum Nordbayern, Paleontology, Friedrich-Alexander-Universität Erlangen-Nürnberg, Loewenichstraße 28, 91054 Erlangen, Germany
1 shared publication - Christoph Joseph Brabec
Institute of Materials for Electronics and Energy Technology (i‐MEET) Department of Materials Science and Engineering Friedrich‐Alexander‐Universität Erlangen‐Nürnberg Erlangen Germany
1 shared publication
Latest Publications
- Open Access
Discrete Phase Selection Driven by Evaporation-Induced Off-Stoichiometry in Melt-Grown CsPbBr3
We show that halide evaporation during melt growth of on polycrystalline FTO under partially open conditions drives discrete phase selection between the line compounds of the CsBr–PbBr2 system, producing a sharp bilayer instead of compositional grading. In situ optical imaging shows that solidification begins with nucleation and lateral growth of a planar single crystal while the melt layer is still thick enough to average over the FTO relief. As the crystal thickens, the residual melt then becomes inhomogeneous and unstable, producing a buried porous layer of faceted grains with a characteristic in-plane spacing of 1–10). This morphology is consistent with a faceted Mullins–Sekerka-type instability under a non-conservative evaporative boundary condition. Beneath the single-crystal cap, the first-formed faceted islands are large and become progressively smaller as the advancing front approaches the FTO pyramids, while elevated ambient halide partial pressure suppresses the instability, consistent with diffusion–capillarity selection under decreasing residual melt thickness and steepening local gradients, modified by evaporative flux. Oxygen associated with microvoids or the oxide substrate enables a secondary reaction–diffusion pathway forming Pb–Br–O crystallites without altering the primary length scale. These results identify evaporation as an active control parameter coupling phase equilibria and interfacial stability in volatile halide melts. In the buried, porous bilayer morphology observed here, the secondary phases and porosity reduce the active volume and are expected to degrade scintillation through increased trapping, nonradiative recombination, and light scattering.Open AccessDiscrete Phase Selection Driven by Evaporation-Induced Off-Stoichiometry in Melt-Grown CsPbBr3
We show that halide evaporation during melt growth of on polycrystalline FTO under partially open conditions drives discrete phase selection between the line compounds of the CsBr–PbBr2 system, producing a sharp bilayer instead of compositional grading. In situ optical imaging shows that solidification begins with nucleation and lateral growth of a planar single crystal while the melt layer is still thick enough to average over the FTO relief. As the crystal thickens, the residual melt then becomes inhomogeneous and unstable, producing a buried porous layer of faceted grains with a characteristic in-plane spacing of 1–10). This morphology is consistent with a faceted Mullins–Sekerka-type instability under a non-conservative evaporative boundary condition. Beneath the single-crystal cap, the first-formed faceted islands are large and become progressively smaller as the advancing front approaches the FTO pyramids, while elevated ambient halide partial pressure suppresses the instability, consistent with diffusion–capillarity selection under decreasing residual melt thickness and steepening local gradients, modified by evaporative flux. Oxygen associated with microvoids or the oxide substrate enables a secondary reaction–diffusion pathway forming Pb–Br–O crystallites without altering the primary length scale. These results identify evaporation as an active control parameter coupling phase equilibria and interfacial stability in volatile halide melts. In the buried, porous bilayer morphology observed here, the secondary phases and porosity reduce the active volume and are expected to degrade scintillation through increased trapping, nonradiative recombination, and light scattering. - Open Access
- 5 March 2026
- Published by Wiley in Advanced Electronic Materials
- Vol. 12 (7)
Performance Enhancement in Hafnium Oxide Through Homogeneous and Heterogeneous co‐Doping Strategies
Fluorite structure ferroelectrics, especially hafnium oxide, are widely investigated for their application in non‐volatile memories, sensors, actuators, RF devices, and energy harvesters. Due to the metastable nature of the ferroelectric phase in these materials, dopants, and process parameters need to be optimized for its stabilization. Here, we present clear evidence of how dopants affect the properties in this material system and solutions to achieve improved reliability, desired crystallization behavior, and polarization hysteresis shape/position through co‐doping. Finally, the benefits of co‐doping in a variety of application fields are demonstrated. This study provides a comprehensive ‘co‐doping toolkit’ for tailoring fluorite‐structure ferroelectrics to meet specific application requirements.
- 5 March 2026
- Published by Wiley in Advanced Electronic Materials
- Vol. 12 (7)
Open AccessPerformance Enhancement in Hafnium Oxide Through Homogeneous and Heterogeneous co‐Doping Strategies
Fluorite structure ferroelectrics, especially hafnium oxide, are widely investigated for their application in non‐volatile memories, sensors, actuators, RF devices, and energy harvesters. Due to the metastable nature of the ferroelectric phase in these materials, dopants, and process parameters need to be optimized for its stabilization. Here, we present clear evidence of how dopants affect the properties in this material system and solutions to achieve improved reliability, desired crystallization behavior, and polarization hysteresis shape/position through co‐doping. Finally, the benefits of co‐doping in a variety of application fields are demonstrated. This study provides a comprehensive ‘co‐doping toolkit’ for tailoring fluorite‐structure ferroelectrics to meet specific application requirements.