Hui Shan Boo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hui Shan Boo has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Aufa Dahlia Bahar
Department of Paediatric Dentistry and Orthodontics, Faculty of Dentistry, Universiti Malaya, Kuala Lumpur, Malaysia
2 shared publications - Norhidayah Nor Zahidah Mohd Tahir
Department of Paediatric Dentistry and Orthodontics, Faculty of Dentistry, Universiti Malaya, Kuala Lumpur, Malaysia
2 shared publications - Saritha Sivarajan
Department of Paediatric Dentistry and Orthodontics, Faculty of Dentistry, Universiti Malaya, Kuala Lumpur, Malaysia
2 shared publications - Simon J. Littlewood
From the Department of Orthodontics, St Luke's Hospital, Bradford, West Yorkshire, England, United Kingdom
2 shared publications - Alia Amani Abdul Aziz
Ministry of Health, Government Dental Clinics, Putrajaya, Malaysia
1 shared publication - Mohd Shahriman Adenan
Smart Manufacturing Research Institute, Faculty of Mechanical Engineering, Universiti Teknologi MARA, Shah Alam, Malaysia
1 shared publication
Latest Publications
- Open Access
- 17 March 2026
- Published by Springer Nature in Clinical Oral Investigations
- Vol. 30 (4)
A Randomised Controlled Trial Comparing Thermoformed and 3D-Printed Retainers in Young Adults: Evaluation of Post-treatment Stability and Patient Satisfaction
Introduction: To compare post-treatment stability and oral health–related quality of life (OHRQoL) in young adults wearing thermoformed retainers (TFR) versus direct 3D-printed retainers (3DPR) over a six-month part-time retention period. Materials and methods: This single-centre, two-arm parallel randomised controlled trial allocated 30 debonded orthodontic patients (≥ 18 years) to either TFR (Erkodur PETG, 1.0 mm) or 3DPR (NextDent Ortho Flex, 0.75 mm) in a 1:1 ratio. All retainers were worn part-time (8–12 h/day). Digital intraoral scans were obtained at baseline (T0) and six months (T2) using Trios 3, and post-treatment stability was assessed digitally using Little’s Irregularity Index, intercanine width, intermolar width, arch length, overjet, and overbite. OHRQoL was evaluated at both time points using the OHIP-14(M) questionnaire. Non-parametric tests were applied following the Shapiro–Wilk assessment, and analyses were conducted using an intention-to-treat approach. Results: One dropout in the 3DPR group at T2. At T2, no significant between-group differences were found in Little’s Irregularity Index, intercanine width, intermolar width, arch length, or overjet ( p > 0.05). Overbite values were statistically higher in the TFR group at T2 ( p < 0.05); however, the difference was not clinically significant. Changes in post-treatment stability from T0 to T2 (ΔT2–T0) did not differ significantly between groups ( p > 0.05). Total OHIP-14(M) scores improved significantly from T0 to T2 in both groups (TFR p = 0.016; 3DPR p = 0.013), with no significant between-group differences at either time point ( p > 0.05). A small but significant difference was observed in the psychological disability domain at T2, with slightly higher scores in the 3DPR group ( p = 0.020). No harm was observed. Conclusions: TFR and 3DPR demonstrated comparable post-treatment stability and similar improvements in OHRQoL after six months of part-time wear. Registration: ClinicalTrials.gov (Identifier NCT05968625). Protocol: The protocol was published before trial commencement
- 17 March 2026
- Published by Springer Nature in Clinical Oral Investigations
- Vol. 30 (4)
Open AccessA Randomised Controlled Trial Comparing Thermoformed and 3D-Printed Retainers in Young Adults: Evaluation of Post-treatment Stability and Patient Satisfaction
Introduction: To compare post-treatment stability and oral health–related quality of life (OHRQoL) in young adults wearing thermoformed retainers (TFR) versus direct 3D-printed retainers (3DPR) over a six-month part-time retention period. Materials and methods: This single-centre, two-arm parallel randomised controlled trial allocated 30 debonded orthodontic patients (≥ 18 years) to either TFR (Erkodur PETG, 1.0 mm) or 3DPR (NextDent Ortho Flex, 0.75 mm) in a 1:1 ratio. All retainers were worn part-time (8–12 h/day). Digital intraoral scans were obtained at baseline (T0) and six months (T2) using Trios 3, and post-treatment stability was assessed digitally using Little’s Irregularity Index, intercanine width, intermolar width, arch length, overjet, and overbite. OHRQoL was evaluated at both time points using the OHIP-14(M) questionnaire. Non-parametric tests were applied following the Shapiro–Wilk assessment, and analyses were conducted using an intention-to-treat approach. Results: One dropout in the 3DPR group at T2. At T2, no significant between-group differences were found in Little’s Irregularity Index, intercanine width, intermolar width, arch length, or overjet ( p > 0.05). Overbite values were statistically higher in the TFR group at T2 ( p < 0.05); however, the difference was not clinically significant. Changes in post-treatment stability from T0 to T2 (ΔT2–T0) did not differ significantly between groups ( p > 0.05). Total OHIP-14(M) scores improved significantly from T0 to T2 in both groups (TFR p = 0.016; 3DPR p = 0.013), with no significant between-group differences at either time point ( p > 0.05). A small but significant difference was observed in the psychological disability domain at T2, with slightly higher scores in the 3DPR group ( p = 0.020). No harm was observed. Conclusions: TFR and 3DPR demonstrated comparable post-treatment stability and similar improvements in OHRQoL after six months of part-time wear. Registration: ClinicalTrials.gov (Identifier NCT05968625). Protocol: The protocol was published before trial commencement