Ameer Mohammed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ameer Mohammed has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Abdulbasit Hassan
Aerospace Engineering Department, Air Force Institute of Technology, Kaduna – Nigeria
1 shared publication- Abdussalam El-Suleiman
Air Force Institute of Technology, (AFIT)
1 shared publication B.G. Ibrahim
Centre for Defence Procurement Logistics and Supply Chain Management Air Force Institute of Technology Kaduna Kaduna State Nigeria
1 shared publicationG.A. Bolorunduro
Aerospace Engineering Department Air Force Institute of Technology Kaduna Kaduna State Nigeria
1 shared publicationJamilu U. Yahaya
Mechatronic Engineering Department, Air Force Institute of Technology, Kaduna– Nigeria
1 shared publicationKhalid K Dandago
Aerospace Engineering Department, Air Force Institute of Technology, Kaduna – Nigeria
1 shared publication
Latest Publications
- 11 March 2026
- Published by Trans Tech Publications, Ltd. in Engineering Headway
- Vol. 37, 3-14
Analysis of Aircraft Accidents and Serious Incidents in Nigeria (2000-2020): Causes, Consequences and Safety Recommendations
This research aimed to analyze aircraft incidents and accidents in Nigeria during the specified period, identify and categorize their attributes, delineate trends, and evaluate preventive recommendations. Data were collected from the Nigerian Safety Investigation Bureau (NSIB) and the Aviation Safety Network (ASN). The Key findings were as follows: accidents accounted for 38% of recorded occurrences, while serious incidents comprised 62%. A total of 613 fatalities were recorded. Fixed-wing aircraft were involved in 79% of occurrences, with rotary-wing aircraft accounting for 21%. The landing phase was the most occurrence-prone, and passenger flights had the highest number of recorded incidents. Non-fatal occurrences were more common than fatal ones, with human and organizational factors being predominant causes. Lagos, Abuja, Port Harcourt, and Zaria were identified as high-frequency locations. Most recommendations focused on improving organizational procedures and regulations.
- 11 March 2026
- Published by Trans Tech Publications, Ltd. in Engineering Headway
- Vol. 37, 3-14
Analysis of Aircraft Accidents and Serious Incidents in Nigeria (2000-2020): Causes, Consequences and Safety Recommendations
This research aimed to analyze aircraft incidents and accidents in Nigeria during the specified period, identify and categorize their attributes, delineate trends, and evaluate preventive recommendations. Data were collected from the Nigerian Safety Investigation Bureau (NSIB) and the Aviation Safety Network (ASN). The Key findings were as follows: accidents accounted for 38% of recorded occurrences, while serious incidents comprised 62%. A total of 613 fatalities were recorded. Fixed-wing aircraft were involved in 79% of occurrences, with rotary-wing aircraft accounting for 21%. The landing phase was the most occurrence-prone, and passenger flights had the highest number of recorded incidents. Non-fatal occurrences were more common than fatal ones, with human and organizational factors being predominant causes. Lagos, Abuja, Port Harcourt, and Zaria were identified as high-frequency locations. Most recommendations focused on improving organizational procedures and regulations.
- Open Access
- 3 November 2022
- Published by University of Nigeria in Nigerian Journal of Technology
- Vol. 41 (4) , 767-777
Analysis and remedies for factors responsible for time between overhaul: a case study of Do-228 aircraft starter generator
The starter generator is used for cranking the engine and to produce electricity for the aircraft system after a sustainable speed. A review of relevant literature reveals the time between the overhaul of the Do-228 aircraft starter generator but did not go in-depth to unravel the factors responsible. A survey research method is adopted to elicit information on the factors. Raosoft sample technique calculator: a software that primarily calculates or generates the sample size of a research or survey was used to obtain the minimum sample size from the study population with the nominal rolls of the technicians as the sampling frame. The questionnaire was vetted and validated by a professional focus group discussion team. The result shows that the factors responsible for the time between overhaul of the starter generator are Environmental Factors (10%), Mechanical Factors (20%), Poor Maintenance Factors (17%), Time Due (25%), Usage/Life Cycle (16%) and Aging (12%). 75% overhaul is unscheduled. It is recommended that the overhauling of the aircraft starter generators be done at 900 as against 1000 flight hour intervals to mitigate unscheduled maintenance.
- 3 November 2022
- Published by University of Nigeria in Nigerian Journal of Technology
- Vol. 41 (4) , 767-777
Open AccessAnalysis and remedies for factors responsible for time between overhaul: a case study of Do-228 aircraft starter generator
The starter generator is used for cranking the engine and to produce electricity for the aircraft system after a sustainable speed. A review of relevant literature reveals the time between the overhaul of the Do-228 aircraft starter generator but did not go in-depth to unravel the factors responsible. A survey research method is adopted to elicit information on the factors. Raosoft sample technique calculator: a software that primarily calculates or generates the sample size of a research or survey was used to obtain the minimum sample size from the study population with the nominal rolls of the technicians as the sampling frame. The questionnaire was vetted and validated by a professional focus group discussion team. The result shows that the factors responsible for the time between overhaul of the starter generator are Environmental Factors (10%), Mechanical Factors (20%), Poor Maintenance Factors (17%), Time Due (25%), Usage/Life Cycle (16%) and Aging (12%). 75% overhaul is unscheduled. It is recommended that the overhauling of the aircraft starter generators be done at 900 as against 1000 flight hour intervals to mitigate unscheduled maintenance.
- Open Access
- 1 September 2021
- Published by Ahmadu Bello University Zaria in Zaria Journal of Electrical Engineering Technology
- Vol. 10 (2) , 1-7
ASSESSMENT OF PID-BASED CONTROL OF SERVOACTUATORS FOR FLIGHT REGULATION OF SMALL UNMANNED AERIAL VEHICLES
Flight control systems for unmanned aerial vehicles (UAVs) are responsible for maintaining safe flight – they are required to be reliable and robust. Flight regulation is achieved by controlling servomotors linked to flight control surfaces – ailerons, rudder, elevators and flaps. The most important parameters in servomotor control are position and speed. Hence, this work performed an assessment of proportional integral and derivative based controllers for servo motors used in attitude control of UAVs. In the experiment, the performance of proportional-velocity (PV) position and proportional-integral (PI) speed controllers were investigated by studying the impact of the individual gains on the dynamics of the systems. Both PV position and PI speed controllers demonstrated satisfactory performance with few challenges including presence of measurement noise and steady state error. The PV position controller addressed these challenges with its superior noise suppression ability. This makes it more ideal for controlling servo actuators of flight control surfaces.
- 1 September 2021
- Published by Ahmadu Bello University Zaria in Zaria Journal of Electrical Engineering Technology
- Vol. 10 (2) , 1-7
Open AccessASSESSMENT OF PID-BASED CONTROL OF SERVOACTUATORS FOR FLIGHT REGULATION OF SMALL UNMANNED AERIAL VEHICLES
Flight control systems for unmanned aerial vehicles (UAVs) are responsible for maintaining safe flight – they are required to be reliable and robust. Flight regulation is achieved by controlling servomotors linked to flight control surfaces – ailerons, rudder, elevators and flaps. The most important parameters in servomotor control are position and speed. Hence, this work performed an assessment of proportional integral and derivative based controllers for servo motors used in attitude control of UAVs. In the experiment, the performance of proportional-velocity (PV) position and proportional-integral (PI) speed controllers were investigated by studying the impact of the individual gains on the dynamics of the systems. Both PV position and PI speed controllers demonstrated satisfactory performance with few challenges including presence of measurement noise and steady state error. The PV position controller addressed these challenges with its superior noise suppression ability. This makes it more ideal for controlling servo actuators of flight control surfaces.