Mohamed Sid Ahmed
Research Subjects
Research Interests
Mohamed Sid Ahmed has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Abdelhak Badache
Innovative Materials Laboratory and Renewable Energies (LMIER), Department of Civil Engineering and Publics Works, University of Relizane, Bourmadia City, Relizane BP 48000, Algeria
2 shared publications - Abdelmoutalib Benfrid
Djillali Liabes University, 22000 Sidi Bel Abbes, Algeria
2 shared publications - Ahmed Soufiane Benosman
Ecole Supérieure en Sciences Appliqués de Tlemcen, ESSA-Tlemcen, BP 165 RP, Bel Horizon, Tlemcen 13000, Algeria
2 shared publications - Mohamed Mouli
Department of Civil Engineering, Laboratory of Materials LABMAT, ENPO Maurice Audin, BP. 1523, El Mnaouer, Oran 31000, Algeria
2 shared publications - Mostefa Hacini
Department of Civil Engineering, Laboratory of Materials LABMAT, ENPO Maurice Audin, BP. 1523, El Mnaouer, Oran 31000, Algeria
2 shared publications - Omar Taleb
EOLE (Eau et Ouvrages dans Leur Environnement), Department of Civil Engineering, Faculty of Technology, University of Tlemcen, PB 230, Tlemcen, 13000, Algeria
2 shared publications
Latest Publications
- Open Access
- 15 September 2026
- Published by Engineering Society of Corrosion in Zastita materijala
- Vol. 67 (3) , 479-490
Analysis of thermally treated “plastic-pozzolanic” modified mortars and their mechanical properties
The recycling of plastic waste in construction materials offers a potential pathway toward sustainability while improving thermal performance. This study examines mortars in which natural sand is partially replaced by thermally treated PET waste by a natural source (pozzolan). Three phases were conducted: (i) experimental determination of compressive strength, Young’s modulus, and thermal conductivity at different LCA replacement levels; (ii) homogenization analysis to estimate equivalent elastic and thermal parameters, compared with literature data; and (iii) numerical simulations of heat transfer through simply supported beams with 2 cm and 4 cm coatings. The results indicate that thermally treated PET incorporation reduces compressive strength relative to the control mortar, though values remain sufficient for non-structural applications such as finishing mortars (e.g., 22 MPa at 100% substitution). In contrast, thermal performance improved significantly, with conductivity decreasing from 1.5 to 0.71 W/m·K, leading to enhanced resistance to heat transfer. These findings demonstrate the potential of thermally treated PET-modified mortars as eco-efficient materials that combine adequate mechanical capacity with excellent thermal comfort.
- 15 September 2026
- Published by Engineering Society of Corrosion in Zastita materijala
- Vol. 67 (3) , 479-490
Open AccessAnalysis of thermally treated “plastic-pozzolanic” modified mortars and their mechanical properties
The recycling of plastic waste in construction materials offers a potential pathway toward sustainability while improving thermal performance. This study examines mortars in which natural sand is partially replaced by thermally treated PET waste by a natural source (pozzolan). Three phases were conducted: (i) experimental determination of compressive strength, Young’s modulus, and thermal conductivity at different LCA replacement levels; (ii) homogenization analysis to estimate equivalent elastic and thermal parameters, compared with literature data; and (iii) numerical simulations of heat transfer through simply supported beams with 2 cm and 4 cm coatings. The results indicate that thermally treated PET incorporation reduces compressive strength relative to the control mortar, though values remain sufficient for non-structural applications such as finishing mortars (e.g., 22 MPa at 100% substitution). In contrast, thermal performance improved significantly, with conductivity decreasing from 1.5 to 0.71 W/m·K, leading to enhanced resistance to heat transfer. These findings demonstrate the potential of thermally treated PET-modified mortars as eco-efficient materials that combine adequate mechanical capacity with excellent thermal comfort.