Agus Sentana
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Agus Sentana has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Agus Sifa
Manufacturing Design, Politeknik Negeri Indramayu, Jl. Lohbener lama no.8, Indramayu, Jawa Barat, 45252, Indonesia
2 shared publications - Ario Sunar Baskoro
Department of Mechanical Engineering, Faculty of Engineering, Universitas Indonesia, Depok, Indonesia
2 shared publications - Afrizal Riyantono1 shared publication
Aqmal Faris Akbar
1 shared publicationArio Sunar Baskoro
Universitas Indonesia
1 shared publication- Faza Khoirina1 shared publication
Latest Publications
- Open Access
- 29 June 2026
- Published by Elsevier in Next Materials
- Vol. 13
Bead geometry and surface roughness of ER 5356 single layer produced by wire arc additive manufacturing - gas tungsten arc welding (WAAM-GTAW)
- 29 June 2026
- Published by Elsevier in Next Materials
- Vol. 13
Open AccessBead geometry and surface roughness of ER 5356 single layer produced by wire arc additive manufacturing - gas tungsten arc welding (WAAM-GTAW)
- Open Access
- 24 June 2026
- Published by Atlantis Press SARL
- p. 215-230
Clamping Strategy for Single-Layer Wire Arc Additive Manufacturing Using Gas Metal Arc Welding of the AA6061 Substrate and ER5356 Filler
- 24 June 2026
- Published by Atlantis Press SARL
- p. 215-230
Open AccessClamping Strategy for Single-Layer Wire Arc Additive Manufacturing Using Gas Metal Arc Welding of the AA6061 Substrate and ER5356 Filler
- Open Access
- 4 March 2026
- Published by Universitas Pancasila in Teknobiz : Jurnal Ilmiah Program Studi Magister Teknik Mesin
- Vol. 16 (1) , 77-81
Surface waviness of weld bead (layer) of GTAW based wire arc additive manufacturing process
Additive manufacturing has become a focus of industry and research due to the many new developments in processes and systems. This is further strengthened by the trend of resource efficiency, as manufacturing processes towards additive manufacturing offer the possibility of producing close to the required size shape. Additive manufactured products can experience surface imperfections assessed in this study, namely the morphology profile or surface curvature (surface waviness) of the weld bead layer. Generally, surface curvature can be referred to as a "hump" caused by the welding process. To achieve the target of achieving products with relatively minimal surface waviness, experiments and analysis of the manufacturing process using GTAW additive welding on AA 6061 substrate material with ER 5356 filler were conducted. The experiments were carried out by first determining the process parameters and factors that affect the quality of the weld bead layer. The layers stacked in layers were measured for their width and height geometry, surface waviness tests were conducted, and analysis was carried out. The deposition rate or filler deposit, travel speed, and filler feed speed determine the level of surface waviness. In this study, high surface curvature occurred at a wire feeder speed (WFS) of 25 mm/s with a travel speed (TS) of 80 mm/min.
- 4 March 2026
- Published by Universitas Pancasila in Teknobiz : Jurnal Ilmiah Program Studi Magister Teknik Mesin
- Vol. 16 (1) , 77-81
Open AccessSurface waviness of weld bead (layer) of GTAW based wire arc additive manufacturing process
Additive manufacturing has become a focus of industry and research due to the many new developments in processes and systems. This is further strengthened by the trend of resource efficiency, as manufacturing processes towards additive manufacturing offer the possibility of producing close to the required size shape. Additive manufactured products can experience surface imperfections assessed in this study, namely the morphology profile or surface curvature (surface waviness) of the weld bead layer. Generally, surface curvature can be referred to as a "hump" caused by the welding process. To achieve the target of achieving products with relatively minimal surface waviness, experiments and analysis of the manufacturing process using GTAW additive welding on AA 6061 substrate material with ER 5356 filler were conducted. The experiments were carried out by first determining the process parameters and factors that affect the quality of the weld bead layer. The layers stacked in layers were measured for their width and height geometry, surface waviness tests were conducted, and analysis was carried out. The deposition rate or filler deposit, travel speed, and filler feed speed determine the level of surface waviness. In this study, high surface curvature occurred at a wire feeder speed (WFS) of 25 mm/s with a travel speed (TS) of 80 mm/min.