Linye Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Linye Zhang has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
Zhongmin Li
School of Chemistry and Chemical Engineering, Guangxi University, Nanning, 530004, PR China
14 shared publications- Guangtao Wei
School of Chemistry and Chemical Engineering, Guangxi University, Nanning, 530004, PR China
10 shared publications Guangtao Wei
School of Chemistry and Chemical Engineering, Guangxi University, Nanning, 530004, PR China
9 shared publications- Guangtao Wei
School of Chemistry and Chemical Engineering , Guangxi University , Nanning 530004 , China
7 shared publications Luhua Shao
College of Chemistry and Chemical Engineering
5 shared publicationsWenyan Jiang
Department of Chemical Engineering, Guangxi University, Nanning, China
5 shared publications
Latest Publications
- 5 November 2024
- Published by Elsevier in Journal of Environmental Management
- Vol. 371, 123214
Effective nitrate removal with high N2 selectivity by active-site-rich particle electrode of bentonite-based Cu-Fe LDH composite
- 5 November 2024
- Published by Elsevier in Journal of Environmental Management
- Vol. 371, 123214
Effective nitrate removal with high N2 selectivity by active-site-rich particle electrode of bentonite-based Cu-Fe LDH composite
- 1 March 2023
- Published by Elsevier in Journal of Environmental Management
- Vol. 335, 117566
Super facile one-step synthesis of sugarcane bagasse derived N-doped porous biochar for adsorption of ciprofloxacin
- 1 March 2023
- Published by Elsevier in Journal of Environmental Management
- Vol. 335, 117566
Super facile one-step synthesis of sugarcane bagasse derived N-doped porous biochar for adsorption of ciprofloxacin
- Open Access
- 21 November 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (11) , 29125-29142
Insight into catalytic activation of bisulfite for lomefloxacin degradation by simple composite of calcinated red mud
Antibiotic was detected in many environments, and it had posed a serious threat to human health. The advanced oxidation process has been considered an effective way to treat antibiotics. In this work, using industrial waste red mud (RM) as raw material, a series of modified RM (MRM-T; T donates the calcination temperature) was obtained via a facile calcination method and applied to activate sodium bisulfite (NaHSO3) for the lomefloxacin (LOM) degradation. Among all MRM-T, MRM-700 exhibited superior catalytic activity, and approximately 89% of LOM (10 mg/L) was degraded at 30 min through the activation of NaHSO3 ([NaHSO3] = 0.5 g/L) by MRM-700 ([MRM-700] = 0.9 g/L). Moreover, the kinetic constant of LOM removal in the MRM-700/NaHSO3 system (0.082 min−1) was 16.4 times higher than that of the RM-raw/NaHSO3 system (0.005 min−1). The as-synthesized product of MRM-700 was characterized by N2 adsorption–desorption isotherms, X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and Raman spectra. The result indicated that the catalyst possessed excellent pore structure, high specific area, and abundant Fe3+ sites, and the lattice of Fe2O3 was doped after calcination, both of which were favorable for the activation of NaHSO3. The quenching experiment proved that •SO4− and •OH− active species were produced in MRM-700/NaHSO3 system, and •SO4− played a dominant role in LOM removal. In addition, the potential LOM degradation pathway was analyzed via UPLC-MS technology and density functional theory (DFT) calculation, and the toxicity of the treated LOM solution was tested by the culture of mung bean sprouts. This study not only provided a feasible strategy for the valuable use of RM to activate NaHSO3 but also offered a cost-effective catalyst for the efficient removal of pollutants in wastewater.
- 21 November 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (11) , 29125-29142
Open AccessInsight into catalytic activation of bisulfite for lomefloxacin degradation by simple composite of calcinated red mud
Antibiotic was detected in many environments, and it had posed a serious threat to human health. The advanced oxidation process has been considered an effective way to treat antibiotics. In this work, using industrial waste red mud (RM) as raw material, a series of modified RM (MRM-T; T donates the calcination temperature) was obtained via a facile calcination method and applied to activate sodium bisulfite (NaHSO3) for the lomefloxacin (LOM) degradation. Among all MRM-T, MRM-700 exhibited superior catalytic activity, and approximately 89% of LOM (10 mg/L) was degraded at 30 min through the activation of NaHSO3 ([NaHSO3] = 0.5 g/L) by MRM-700 ([MRM-700] = 0.9 g/L). Moreover, the kinetic constant of LOM removal in the MRM-700/NaHSO3 system (0.082 min−1) was 16.4 times higher than that of the RM-raw/NaHSO3 system (0.005 min−1). The as-synthesized product of MRM-700 was characterized by N2 adsorption–desorption isotherms, X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and Raman spectra. The result indicated that the catalyst possessed excellent pore structure, high specific area, and abundant Fe3+ sites, and the lattice of Fe2O3 was doped after calcination, both of which were favorable for the activation of NaHSO3. The quenching experiment proved that •SO4− and •OH− active species were produced in MRM-700/NaHSO3 system, and •SO4− played a dominant role in LOM removal. In addition, the potential LOM degradation pathway was analyzed via UPLC-MS technology and density functional theory (DFT) calculation, and the toxicity of the treated LOM solution was tested by the culture of mung bean sprouts. This study not only provided a feasible strategy for the valuable use of RM to activate NaHSO3 but also offered a cost-effective catalyst for the efficient removal of pollutants in wastewater.
- 27 September 2022
- Published by Elsevier in Journal of Environmental Management
- Vol. 324, 116301
Valorization of ball-milled waste red mud into heterogeneous catalyst as effective peroxymonosulfate activator for tetracycline hydrochloride degradation
- 27 September 2022
- Published by Elsevier in Journal of Environmental Management
- Vol. 324, 116301
Valorization of ball-milled waste red mud into heterogeneous catalyst as effective peroxymonosulfate activator for tetracycline hydrochloride degradation
- 7 March 2022
- Published by Springer Nature in Journal of Materials Science
- Vol. 57 (10) , 5964-5986
Synthesis of organobentonite-supported Pd composite catalyst used for the catalytic transfer hydrogenation of polyunsaturated fatty acid methyl ester
- 7 March 2022
- Published by Springer Nature in Journal of Materials Science
- Vol. 57 (10) , 5964-5986
Synthesis of organobentonite-supported Pd composite catalyst used for the catalytic transfer hydrogenation of polyunsaturated fatty acid methyl ester
- 11 April 2021
- Published by Taylor & Francis in Environmental Technology
- Vol. 43 (19) , 2922-2933
Preparation and application of a new Fenton-like catalyst from red mud for degradation of sulfamethoxazole
In this work, using molasses wastewater as a partial acidifying agent and bagasse pith as a pore-enlarging agent, a new low-cost Fenton-like catalyst (ACRMbp) used for degradation of sulfamethoxazole was prepared through a simple process of acidification and calcination using red mud (RM) as the main material. The optimum preparation conditions of ACRMbp were acquired, and the optimum preparation conditions of ACRMbp were as follows: mass ratio of bagasse pith to RM (mbp:mRM) 0.033:1, particle size of bagasse pith 0.10–0.20 mm, calcination temperature 773 K, and calcination time 2 h. The ACRMbp catalyst was characterized by XRD, SEM, EDS, and BET. According to the results of characterizations, it was found that the iron phase of ACRMbp had completely transformed into α-Fe2O3 after the process of acidification and calcination, and the addition of bagasse pith significantly improved the surface area of the prepared ACRMbp. Furthermore, under the reaction conditions of catalyst dosage of 2 g/L, initial pH 3 and reaction time 90 min, the ACRMbp has showed the highest catalytic activity. ACRMbp had significantly higher activity than red mud, and exhibited a remarkable settleability. Besides, ACRMbp retained good recyclability and stability during use. Kinetic studies showed the degradation process could be described with the first-order model. Overall, the prepared ACRMbp was an effective and excellent catalyst in the Fenton-like process. GRAPHICAL ABSTRACT
- 11 April 2021
- Published by Taylor & Francis in Environmental Technology
- Vol. 43 (19) , 2922-2933
Preparation and application of a new Fenton-like catalyst from red mud for degradation of sulfamethoxazole
In this work, using molasses wastewater as a partial acidifying agent and bagasse pith as a pore-enlarging agent, a new low-cost Fenton-like catalyst (ACRMbp) used for degradation of sulfamethoxazole was prepared through a simple process of acidification and calcination using red mud (RM) as the main material. The optimum preparation conditions of ACRMbp were acquired, and the optimum preparation conditions of ACRMbp were as follows: mass ratio of bagasse pith to RM (mbp:mRM) 0.033:1, particle size of bagasse pith 0.10–0.20 mm, calcination temperature 773 K, and calcination time 2 h. The ACRMbp catalyst was characterized by XRD, SEM, EDS, and BET. According to the results of characterizations, it was found that the iron phase of ACRMbp had completely transformed into α-Fe2O3 after the process of acidification and calcination, and the addition of bagasse pith significantly improved the surface area of the prepared ACRMbp. Furthermore, under the reaction conditions of catalyst dosage of 2 g/L, initial pH 3 and reaction time 90 min, the ACRMbp has showed the highest catalytic activity. ACRMbp had significantly higher activity than red mud, and exhibited a remarkable settleability. Besides, ACRMbp retained good recyclability and stability during use. Kinetic studies showed the degradation process could be described with the first-order model. Overall, the prepared ACRMbp was an effective and excellent catalyst in the Fenton-like process. GRAPHICAL ABSTRACT
- 18 March 2021
- Published by Hindawi Limited in International Journal of Energy Research
- Vol. 45 (9) , 13098-13116
Microwave‐assisted catalytic transfer hydrogenation of fatty acid methyl esters using metal‐doped nickel‐boride ‐ cetyltrimethylammonium bromide amorphous alloy catalyst
Modified nickel‐boride (Ni‐B)‐based amorphous alloy catalysts used for microwave‐assisted catalytic transfer hydrogenation (CTH) of fatty acid methyl esters (FAMEs) had been synthesized via chemical reduction method by adding simultaneously cetyltrimethylammonium bromide (CTAB) and various transition metals. The results suggested that Cr‐doped Ni‐B‐CTAB catalyst showed superior catalytic activity. It was found that Ni‐Cr‐B‐CTAB catalyst remained an amorphous structure and had a smaller particle size with less agglomeration as compared with Ni‐B catalyst. What's more, the specific surface area of the catalyst increased obviously with the addition of CTAB and Cr into Ni‐B catalyst. Under the established optimum conditions of CTH using Ni‐Cr‐B‐CTAB as a catalyst, the conversion ratio of methyl linoleate reached 78.05% and the properties of hydrogenated FAMEs were improved obviously. This work has provided a feasible approach to prepare a new and efficient Ni‐Cr‐B‐CTAB amorphous alloy catalyst for the CTH of FAMEs and thus to obtained the high‐quality hydrogenated FAMEs.
- 18 March 2021
- Published by Hindawi Limited in International Journal of Energy Research
- Vol. 45 (9) , 13098-13116
Microwave‐assisted catalytic transfer hydrogenation of fatty acid methyl esters using metal‐doped nickel‐boride ‐ cetyltrimethylammonium bromide amorphous alloy catalyst
Modified nickel‐boride (Ni‐B)‐based amorphous alloy catalysts used for microwave‐assisted catalytic transfer hydrogenation (CTH) of fatty acid methyl esters (FAMEs) had been synthesized via chemical reduction method by adding simultaneously cetyltrimethylammonium bromide (CTAB) and various transition metals. The results suggested that Cr‐doped Ni‐B‐CTAB catalyst showed superior catalytic activity. It was found that Ni‐Cr‐B‐CTAB catalyst remained an amorphous structure and had a smaller particle size with less agglomeration as compared with Ni‐B catalyst. What's more, the specific surface area of the catalyst increased obviously with the addition of CTAB and Cr into Ni‐B catalyst. Under the established optimum conditions of CTH using Ni‐Cr‐B‐CTAB as a catalyst, the conversion ratio of methyl linoleate reached 78.05% and the properties of hydrogenated FAMEs were improved obviously. This work has provided a feasible approach to prepare a new and efficient Ni‐Cr‐B‐CTAB amorphous alloy catalyst for the CTH of FAMEs and thus to obtained the high‐quality hydrogenated FAMEs.
- 2 November 2020
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
- Vol. 41 (1) , 34-43
A functionalized tannin-chitosan bentonite composite with superior adsorption capacity for Cr(VI)
A novel functionalized tannin-chitosan bentonite composite (TCBC) was successfully synthesized. The formation of the composite was confirmed by the X-ray diffraction (XRD) patterns and Fourier transform infrared spectroscopy (FT-IR) analysis. The pHpzc of TCBC was 3.38. The influences such as pH, dosage of TCBC, temperature and initial Cr(VI) concentration on adsorption capacity were investigated. The experimental data indicated that the almost saturated adsorption of the TCBC towards Cr(VI) in 100 min. The maximum adsorption capacity was 262.08 mg/g at 333 K with initial pH = 2.5. The adsorption kinetics of Cr(VI) on TCBC followed the pseudo-second-order kinetics model. The isothermal data were well described by the models of Langmuir, Freundlich and Temkin. The results revealed that the adsorption of Cr(VI) on TCBC existed comprehensive effects and mainly belong to the chemisorption. The TCBC could keep good performances (q e = 192.17 mg/g) in five runs, 1 M NaOH was used as eluent for desorption, which showed a high desorption efficiency. Studies showed TCBC prepared with low cost and green raw materials, and simple green preparation technology had high adsorption capacity, good reusability and acidic tolerance. By exploring the Cr(VI)-Cr(III) hybrid system, part of Cr(VI) was reduced to Cr(III) and adsorbed by TCBC. The optimal adsorption pH of Cr(III) was 5.0.
- 2 November 2020
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
- Vol. 41 (1) , 34-43
A functionalized tannin-chitosan bentonite composite with superior adsorption capacity for Cr(VI)
A novel functionalized tannin-chitosan bentonite composite (TCBC) was successfully synthesized. The formation of the composite was confirmed by the X-ray diffraction (XRD) patterns and Fourier transform infrared spectroscopy (FT-IR) analysis. The pHpzc of TCBC was 3.38. The influences such as pH, dosage of TCBC, temperature and initial Cr(VI) concentration on adsorption capacity were investigated. The experimental data indicated that the almost saturated adsorption of the TCBC towards Cr(VI) in 100 min. The maximum adsorption capacity was 262.08 mg/g at 333 K with initial pH = 2.5. The adsorption kinetics of Cr(VI) on TCBC followed the pseudo-second-order kinetics model. The isothermal data were well described by the models of Langmuir, Freundlich and Temkin. The results revealed that the adsorption of Cr(VI) on TCBC existed comprehensive effects and mainly belong to the chemisorption. The TCBC could keep good performances (q e = 192.17 mg/g) in five runs, 1 M NaOH was used as eluent for desorption, which showed a high desorption efficiency. Studies showed TCBC prepared with low cost and green raw materials, and simple green preparation technology had high adsorption capacity, good reusability and acidic tolerance. By exploring the Cr(VI)-Cr(III) hybrid system, part of Cr(VI) was reduced to Cr(III) and adsorbed by TCBC. The optimal adsorption pH of Cr(III) was 5.0.