Akmaral Zhapakhova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Akmaral Zhapakhova has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Saken Uderbayev
Department of Architecture and Construction Production, Korkyt Ata Kyzylorda University, Kyzylorda 120014, Kazakhstan
7 shared publications - Gulnaz Zhakapbayeva
Department of Architecture and Construction Production, Korkyt Ata Kyzylorda University, Kyzylorda 120014, Kazakhstan
5 shared publications - Nargul Saktaganova
Department of Architecture and Construction Production, Korkyt Ata Kyzylorda University, Kyzylorda 120014, Kazakhstan
5 shared publications - Akbota Arystanbek
Institute of Engineering and Technology, Korkyt Ata Kyzylorda University, Kyzylorda, 29A, Aiteke bi Str., Kyzylorda 120014, Kazakhstan
3 shared publications - Gulnur Zhakypova
Department of Architecture and Construction Production, Korkyt Ata Kyzylorda University, Kyzylorda 120014, Kazakhstan
3 shared publications - Koktem Yerimbetov
Department of Engineering Technologies, Kyzylorda Open University, 72 G. Muratbayev Street, Kyzylorda 120016, Kazakhstan
3 shared publications
Latest Publications
- Open Access
- 5 November 2026
- Published by MDPI AG in Construction Materials
- Vol. 6 (6) , 99
Very-Low-Density Porous Aggregate Produced by Organomineral Surface Dusting with Kyzylorda TPP Ash and Ground Rice Husk
This study evaluates a sintered lightweight aggregate produced from a 70:30 mass ratio of loess-like loam to hydraulic ash from the Kyzylorda thermal power plant (TPP), with an external 50:50 TPP-ash–ground-rice-husk dusting mixture. Four dusting regimes (C0–C3) were examined at 1000, 1030, 1060, and 1100 °C using 15 test specimens or portions per condition. C0 was the undusted control; the dusting-mixture-to-raw-granule mass ratios for C1, C2, and C3 were 1:2.5, 1:3.5, and 1:4.9, respectively. Dusting regime and firing temperature affected density, strength, water absorption, pore structure, and thermal conductivity. The selected C2 regime, corresponding to a dusting-mixture-to-granule ratio of 1:3.5, produced at 1060 °C an aggregate with a bulk density of 324 ± 18 kg/m3, cylinder crushing strength of 1.42 ± 0.08 MPa, water absorption of 15.8 ± 0.6%, and effective packed-bed thermal conductivity of 0.078 W/(m·K). Scanning electron microscopy (SEM) showed porous and consolidated regions; local energy-dispersive X-ray spectroscopy (EDS) indicated higher Ca, Al, and Fe in the examined shell region than in the examined core region. Lightweight concrete containing the developed aggregate achieved a dry density of 920 ± 5 kg/m3, 28-day compressive strength of 3.87 ± 0.22 MPa, water absorption of 19.4 ± 0.3%, and thermal conductivity of 0.215 ± 0.010 W/(m·K). The results identify 1060 °C and the C2 dusting regime as a preferred compromise among the tested conditions, based on a comparative assessment of density, cylinder crushing strength, water absorption, and thermal conductivity rather than a weighted numerical optimization.
- 5 November 2026
- Published by MDPI AG in Construction Materials
- Vol. 6 (6) , 99
Open AccessVery-Low-Density Porous Aggregate Produced by Organomineral Surface Dusting with Kyzylorda TPP Ash and Ground Rice Husk
This study evaluates a sintered lightweight aggregate produced from a 70:30 mass ratio of loess-like loam to hydraulic ash from the Kyzylorda thermal power plant (TPP), with an external 50:50 TPP-ash–ground-rice-husk dusting mixture. Four dusting regimes (C0–C3) were examined at 1000, 1030, 1060, and 1100 °C using 15 test specimens or portions per condition. C0 was the undusted control; the dusting-mixture-to-raw-granule mass ratios for C1, C2, and C3 were 1:2.5, 1:3.5, and 1:4.9, respectively. Dusting regime and firing temperature affected density, strength, water absorption, pore structure, and thermal conductivity. The selected C2 regime, corresponding to a dusting-mixture-to-granule ratio of 1:3.5, produced at 1060 °C an aggregate with a bulk density of 324 ± 18 kg/m3, cylinder crushing strength of 1.42 ± 0.08 MPa, water absorption of 15.8 ± 0.6%, and effective packed-bed thermal conductivity of 0.078 W/(m·K). Scanning electron microscopy (SEM) showed porous and consolidated regions; local energy-dispersive X-ray spectroscopy (EDS) indicated higher Ca, Al, and Fe in the examined shell region than in the examined core region. Lightweight concrete containing the developed aggregate achieved a dry density of 920 ± 5 kg/m3, 28-day compressive strength of 3.87 ± 0.22 MPa, water absorption of 19.4 ± 0.3%, and thermal conductivity of 0.215 ± 0.010 W/(m·K). The results identify 1060 °C and the C2 dusting regime as a preferred compromise among the tested conditions, based on a comparative assessment of density, cylinder crushing strength, water absorption, and thermal conductivity rather than a weighted numerical optimization.
- Open Access
- 10 October 2026
- Published by MDPI AG in Geotechnics
- Vol. 6 (4) , 107
Reliability-Based Correction of Collapse Settlement for Hydraulic Structures on Loess
Using a single mean collapse strain can misrepresent settlement in spatially variable loess foundations, potentially leading to unsafe hydraulic-structure design and settlement-induced damage. This study examines an archival empirical correction classified by ground and structural conditions. Engineering-geological records from 12 sites informed the factor classification, and monitored settlements of seven irrigation structures were used for validation. The resulting composite factors range from 1.30 to 1.44 across the specified ground and structural classes. For the seven field cases, the corrected predictions achieved a mean absolute percentage error of 12.7%, compared with 35.2% and 32.4% for the two conventional calculation sets. Archival physical-model observations independently supported the proposed load-redistribution mechanism. The correction provides a transparent way to account for ground variability and structural response in preliminary and design-stage settlement assessments, provided that representative collapse-strain data and a defined wetting scenario are available.
- 10 October 2026
- Published by MDPI AG in Geotechnics
- Vol. 6 (4) , 107
Open AccessReliability-Based Correction of Collapse Settlement for Hydraulic Structures on Loess
Using a single mean collapse strain can misrepresent settlement in spatially variable loess foundations, potentially leading to unsafe hydraulic-structure design and settlement-induced damage. This study examines an archival empirical correction classified by ground and structural conditions. Engineering-geological records from 12 sites informed the factor classification, and monitored settlements of seven irrigation structures were used for validation. The resulting composite factors range from 1.30 to 1.44 across the specified ground and structural classes. For the seven field cases, the corrected predictions achieved a mean absolute percentage error of 12.7%, compared with 35.2% and 32.4% for the two conventional calculation sets. Archival physical-model observations independently supported the proposed load-redistribution mechanism. The correction provides a transparent way to account for ground variability and structural response in preliminary and design-stage settlement assessments, provided that representative collapse-strain data and a defined wetting scenario are available.
- Open Access
- 7 August 2026
- Published by MDPI AG in Construction Materials
- Vol. 6 (4) , 50
Performance of Concrete with Mechanochemically Activated Rice Husk Ash-Based Organomineral Modifiers
This study evaluates a wet-activated multicomponent organomineral modifier for sustainable concrete. The modifier was produced by co-grinding Portland cement and rice husk ash (RHA) in the presence of Sika® ViscoCrete®-20HE and was subsequently combined with polypropylene fibers. Three modified mixtures were tested after 28 days of curing and compared with a control concrete. The modified concretes achieved compressive strengths of 42.2–45.0 MPa, compared with 36.8 MPa for the control. Among the tested formulations, Mix 2, containing 6 wt.% RHA, 4 wt.% polypropylene fibers, and 1.3 wt.% superplasticizer, showed the most favorable overall performance. Its compressive and flexural strengths reached 45.0 and 5.8 MPa, corresponding to observed differences of 22.3% and 26.1%, respectively, relative to the control formulation. Because the complete mixture compositions and w/c ratios differed, these comparisons do not isolate the contribution of any individual constituent. Fracture toughness increased from 1.15 to 2.16 MPa·m1/2, water absorption decreased from 6.8% to 5.1%, and freeze–thaw resistance increased from 138 to 242 cycles. Qualitative SEM and XRD observations showed morphological and phase-related differences between selected control and modified specimens; however, these observations did not establish the causes of the measured performance differences. In addition, because no compositionally identical non-activated RHA reference or direct reactivity test was included, the independent effect of wet activation on RHA reactivity could not be established. The investigated integrated modifier therefore shows potential for improving concrete performance while enabling the beneficial use of RHA.
- 7 August 2026
- Published by MDPI AG in Construction Materials
- Vol. 6 (4) , 50
Open AccessPerformance of Concrete with Mechanochemically Activated Rice Husk Ash-Based Organomineral Modifiers
This study evaluates a wet-activated multicomponent organomineral modifier for sustainable concrete. The modifier was produced by co-grinding Portland cement and rice husk ash (RHA) in the presence of Sika® ViscoCrete®-20HE and was subsequently combined with polypropylene fibers. Three modified mixtures were tested after 28 days of curing and compared with a control concrete. The modified concretes achieved compressive strengths of 42.2–45.0 MPa, compared with 36.8 MPa for the control. Among the tested formulations, Mix 2, containing 6 wt.% RHA, 4 wt.% polypropylene fibers, and 1.3 wt.% superplasticizer, showed the most favorable overall performance. Its compressive and flexural strengths reached 45.0 and 5.8 MPa, corresponding to observed differences of 22.3% and 26.1%, respectively, relative to the control formulation. Because the complete mixture compositions and w/c ratios differed, these comparisons do not isolate the contribution of any individual constituent. Fracture toughness increased from 1.15 to 2.16 MPa·m1/2, water absorption decreased from 6.8% to 5.1%, and freeze–thaw resistance increased from 138 to 242 cycles. Qualitative SEM and XRD observations showed morphological and phase-related differences between selected control and modified specimens; however, these observations did not establish the causes of the measured performance differences. In addition, because no compositionally identical non-activated RHA reference or direct reactivity test was included, the independent effect of wet activation on RHA reactivity could not be established. The investigated integrated modifier therefore shows potential for improving concrete performance while enabling the beneficial use of RHA.
- Open Access
- 5 August 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (8) , 417
Mechanical Performance, Durability, and Microstructure of Dune-Sand Concrete Incorporating Rice Husk Ash and Dried Oil Sludge
This study evaluates sustainable dune-sand concrete produced using local dune sand, rice husk ash (RHA), and dried oil sludge. The experimental program included a control mixture (C0) and three modified mixtures (M1–M3). RHA was used as a partial replacement for Portland cement at contents of 20, 40, and 60 kg/m3, while dried oil sludge was introduced as a waste-derived additive at 10, 15, and 20 kg/m3, respectively. The total binder content, defined as Portland cement plus RHA, was maintained at 350 kg/m3, while the mixing-water content and water-to-binder ratio were kept constant at 185 kg/m3 and 0.53, respectively. The RHA was heat-treated at 800 °C for 60 min, immediately quenched in water, and subsequently dried at 105 ± 5 °C until a constant mass was achieved. Among the investigated compositions, M2, containing 310 kg/m3 Portland cement, 690 kg/m3 dune sand, 1110 kg/m3 crushed stone, 40 kg/m3 RHA, and 15 kg/m3 dried oil sludge, exhibited the most balanced overall performance. Its compressive strength reached 27.8 MPa at 7 days, 42.5 MPa at 28 days, and 47.7 MPa at 90 days, while its static modulus of elasticity was 32.7 GPa. M2 also showed the lowest water absorption (3.63%), the highest watertightness grade within the investigated series (W10), and the greatest measured freeze–thaw resistance, completing 223 cycles. Optical microscopy and X-ray diffraction observations indicated a visually more continuous matrix and lower relative intensities of several portlandite peaks in the modified concrete. For the replicate-based properties, mixture composition had a statistically significant effect (p < 0.001). Because RHA and dried oil sludge were varied simultaneously, the results represent their combined effect. M2 is therefore identified as the most balanced composition within the present limited test series, rather than as a universal optimum.
- 5 August 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (8) , 417
Open AccessMechanical Performance, Durability, and Microstructure of Dune-Sand Concrete Incorporating Rice Husk Ash and Dried Oil Sludge
This study evaluates sustainable dune-sand concrete produced using local dune sand, rice husk ash (RHA), and dried oil sludge. The experimental program included a control mixture (C0) and three modified mixtures (M1–M3). RHA was used as a partial replacement for Portland cement at contents of 20, 40, and 60 kg/m3, while dried oil sludge was introduced as a waste-derived additive at 10, 15, and 20 kg/m3, respectively. The total binder content, defined as Portland cement plus RHA, was maintained at 350 kg/m3, while the mixing-water content and water-to-binder ratio were kept constant at 185 kg/m3 and 0.53, respectively. The RHA was heat-treated at 800 °C for 60 min, immediately quenched in water, and subsequently dried at 105 ± 5 °C until a constant mass was achieved. Among the investigated compositions, M2, containing 310 kg/m3 Portland cement, 690 kg/m3 dune sand, 1110 kg/m3 crushed stone, 40 kg/m3 RHA, and 15 kg/m3 dried oil sludge, exhibited the most balanced overall performance. Its compressive strength reached 27.8 MPa at 7 days, 42.5 MPa at 28 days, and 47.7 MPa at 90 days, while its static modulus of elasticity was 32.7 GPa. M2 also showed the lowest water absorption (3.63%), the highest watertightness grade within the investigated series (W10), and the greatest measured freeze–thaw resistance, completing 223 cycles. Optical microscopy and X-ray diffraction observations indicated a visually more continuous matrix and lower relative intensities of several portlandite peaks in the modified concrete. For the replicate-based properties, mixture composition had a statistically significant effect (p < 0.001). Because RHA and dried oil sludge were varied simultaneously, the results represent their combined effect. M2 is therefore identified as the most balanced composition within the present limited test series, rather than as a universal optimum.
- Open Access
- 24 June 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (7) , 332
Development of Non-Autoclaved Aerated Concrete Incorporating Rice Husk Ash-Derived Silica and Polypropylene Microfibers for Sustainable Construction
The present study investigates the development of non-autoclaved aerated concrete (NAAC) incorporating rice husk ash (RHA)-derived amorphous silica, polypropylene microfibers, and a polycarboxylate-based superplasticizer to improve mechanical performance and durability while maintaining low density and thermal conductivity. Experimental investigations included density, compressive strength, thermal conductivity, water absorption, X-ray diffraction (XRD), microstructural observations, and TG–DTA analysis. The developed compositions containing 5–7% RHA and 0.10–0.20% polypropylene microfibers achieved compressive strength values of 4.5–4.8 MPa at densities of 520–560 kg/m3, which are comparable to or higher than values commonly reported for non-autoclaved aerated concrete of similar density. Thermal conductivity decreased to 0.12–0.13 W/(m·K), while water absorption was reduced to 15–18%. XRD, microstructural, and TG–DTA analyses suggested enhanced hydration reactions and improved development of the cementitious matrix due to pozzolanic interaction between amorphous silica and calcium hydroxide. The incorporation of polypropylene microfibers was associated with improved structural homogeneity of the developed NAAC compositions, whereas the superplasticizer enhanced mixture homogeneity and pore stability. The results suggest that the combined use of agricultural waste-derived silica and fiber reinforcement provides an effective approach for producing sustainable and energy-efficient NAAC without autoclave curing.
- 24 June 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (7) , 332
Open AccessDevelopment of Non-Autoclaved Aerated Concrete Incorporating Rice Husk Ash-Derived Silica and Polypropylene Microfibers for Sustainable Construction
The present study investigates the development of non-autoclaved aerated concrete (NAAC) incorporating rice husk ash (RHA)-derived amorphous silica, polypropylene microfibers, and a polycarboxylate-based superplasticizer to improve mechanical performance and durability while maintaining low density and thermal conductivity. Experimental investigations included density, compressive strength, thermal conductivity, water absorption, X-ray diffraction (XRD), microstructural observations, and TG–DTA analysis. The developed compositions containing 5–7% RHA and 0.10–0.20% polypropylene microfibers achieved compressive strength values of 4.5–4.8 MPa at densities of 520–560 kg/m3, which are comparable to or higher than values commonly reported for non-autoclaved aerated concrete of similar density. Thermal conductivity decreased to 0.12–0.13 W/(m·K), while water absorption was reduced to 15–18%. XRD, microstructural, and TG–DTA analyses suggested enhanced hydration reactions and improved development of the cementitious matrix due to pozzolanic interaction between amorphous silica and calcium hydroxide. The incorporation of polypropylene microfibers was associated with improved structural homogeneity of the developed NAAC compositions, whereas the superplasticizer enhanced mixture homogeneity and pore stability. The results suggest that the combined use of agricultural waste-derived silica and fiber reinforcement provides an effective approach for producing sustainable and energy-efficient NAAC without autoclave curing.
- Open Access
Effect of Kyzylorda Thermal Power Plant Ash and Rice Husk Ash on the Physical and Mechanical Properties of Ceramic Materials
This study investigates the development of sustainable ceramic materials using industrial and agricultural waste from the Kyzylorda region of Kazakhstan. The research focuses on the combined use of local clay, ash from the Kyzylorda thermal power plant (TPP), and rice husk ash (RHA). Experimental investigations included the evaluation of chemical composition, linear and volumetric shrinkage, water absorption, bulk density, and compressive strength of ceramic samples fired at 950–1050 °C. Microstructural (SEM) and phase composition (XRD) analyses were performed to explain the observed behavior. The results showed that the optimal composition was 70% clay, 20% TPP ash, and 10% RHA, which demonstrated the highest compressive strength (15.45 MPa), reduced water absorption, and improved densification. The enhanced performance is attributed to partial vitrification and viscous-phase-assisted densification and the formation of crystalline phases such as mullite, cristobalite, and anorthite. The study confirms that the combined use of TPP ash and RHA enables effective recycling of local waste materials and improves the physical and mechanical properties of ceramic products.
Open AccessEffect of Kyzylorda Thermal Power Plant Ash and Rice Husk Ash on the Physical and Mechanical Properties of Ceramic Materials
This study investigates the development of sustainable ceramic materials using industrial and agricultural waste from the Kyzylorda region of Kazakhstan. The research focuses on the combined use of local clay, ash from the Kyzylorda thermal power plant (TPP), and rice husk ash (RHA). Experimental investigations included the evaluation of chemical composition, linear and volumetric shrinkage, water absorption, bulk density, and compressive strength of ceramic samples fired at 950–1050 °C. Microstructural (SEM) and phase composition (XRD) analyses were performed to explain the observed behavior. The results showed that the optimal composition was 70% clay, 20% TPP ash, and 10% RHA, which demonstrated the highest compressive strength (15.45 MPa), reduced water absorption, and improved densification. The enhanced performance is attributed to partial vitrification and viscous-phase-assisted densification and the formation of crystalline phases such as mullite, cristobalite, and anorthite. The study confirms that the combined use of TPP ash and RHA enables effective recycling of local waste materials and improves the physical and mechanical properties of ceramic products.
- Open Access
- 9 April 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (4) , 202
Mathematical Modeling of the Raw Material Composition of Composite Material from Agricultural Plant Waste in South Kazakhstan
This study investigates the development of a composite material based on agricultural plant waste from Kazakhstan, utilizing a multicomponent binder incorporated with rice husk ash. The implementation of low-clinker binders enables the full utilization of ash dumps from the Kyzylorda thermal power plant (TPP) and rice husk residues from local rice-processing enterprises. Physical and chemical analysis of the ash–cement stone revealed a reduction in portlandite content compared to control samples. Phase composition analysis indicated the presence of hydroaluminate C4AH13 and a reduction in calcite, suggesting accelerated crystallization of calcium silicate hydrates. The formation of crystalline phases and intergrowth structures is assumed to contribute to the strengthening of the gel-like matrix. Experimental optimization of the ash–cement binder with rice husk ash yielded compressive strengths ranging from 3.03 to 4.10 MPa at densities of 790–900 kg/m3, depending on the type of organic filler. These results confirm the feasibility of using locally sourced agricultural waste for the production of heat-insulating and structurally stable composite materials.
- 9 April 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (4) , 202
Open AccessMathematical Modeling of the Raw Material Composition of Composite Material from Agricultural Plant Waste in South Kazakhstan
This study investigates the development of a composite material based on agricultural plant waste from Kazakhstan, utilizing a multicomponent binder incorporated with rice husk ash. The implementation of low-clinker binders enables the full utilization of ash dumps from the Kyzylorda thermal power plant (TPP) and rice husk residues from local rice-processing enterprises. Physical and chemical analysis of the ash–cement stone revealed a reduction in portlandite content compared to control samples. Phase composition analysis indicated the presence of hydroaluminate C4AH13 and a reduction in calcite, suggesting accelerated crystallization of calcium silicate hydrates. The formation of crystalline phases and intergrowth structures is assumed to contribute to the strengthening of the gel-like matrix. Experimental optimization of the ash–cement binder with rice husk ash yielded compressive strengths ranging from 3.03 to 4.10 MPa at densities of 790–900 kg/m3, depending on the type of organic filler. These results confirm the feasibility of using locally sourced agricultural waste for the production of heat-insulating and structurally stable composite materials.