CWChen Wu

Chen Wu

*This is an algorithmically generated author record based on publicly available information.

Chen Wu has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Enhanced chloride transport resistance and corrosion protection of reinforced concrete by NO2-LDHs@MMT: Electrochemical evaluation and coupled modeling

    by Xiaoyi Zhang, Hongrun Cai, Huibin Cheng, Guoliang Lin, Chen Wu, Wanxi Jiang, Wenjin Huang, Biqiong Hong

    Chloride-induced corrosion of reinforcing steel is a major cause of durability deterioration in reinforced concrete, whereas the efficiency of layered double hydroxides (LDHs) is often limited by agglomeration in cementitious systems. This study investigated a NO2-intercalated LDH/montmorillonite composite (NO2-LDHs@MMT) as a multifunctional additive for improving chloride resistance and corrosion protection, with NO2-LDHs as a reference. Rapid chloride migration (RCM), open-circuit potential (OCP), electrochemical impedance spectroscopy (EIS), and Tafel polarization were combined with a coupled chloride transport-corrosion model. Both additives reduced chloride migration, but NO2-LDHs@MMT showed the stronger effect. At 2 wt.% of binder, the chloride migration coefficient decreased from 14.3 × 10−12 to 8.3 × 10−12 m2/s, corresponding to a 41.95% reduction. Under electrically accelerated chloride ingress, the 2 wt.% NO2-LDHs@MMT specimen maintained a more positive OCP (−0.279 V vs. SCE at 162 h), a much higher charge-transfer resistance (3010 kΩ·cm2), and a markedly lower corrosion current density (0.0312 × 10−5 A·cm−2) than the blank specimen, yielding an inhibition efficiency of 99.5%. The coupled model reproduced the measured corrosion current with a simulated-to-measured ratio of 0.918-0.97 and predicted lower chloride accumulation, thinner corrosion products, and less damage during 300 d exposure. The improved performance of NO2-LDHs@MMT is associated with chloride capture, better LDH dispersion, and a larger effective interaction interface provided by MMT.

  • Open Access

    Seismic damage evaluation of unsymmetrical steel-reinforced concrete columns via embedded piezoelectric transducers

    by Hong Xiang, Qiyun Liu, Shiyi Hu, Chen Wu, Huibin Cheng

    The damage process of a component/structure results from the continuous evolution and accumulation of material deterioration. A higher degree of damage indicates a more severe structural condition. This study investigated the seismic damage behavior of unsymmetrical steel-reinforced concrete (USRC) columns through low cyclic loading tests conducted on eight specimens. The height range corresponding to the most unfavorable damage section of the columns was examined. The correlation between the damage evolution of single- and multi-point concrete materials and the plastic development of components was established using embedded piezoelectric transducers and the stress transformation damage factor. The average concrete compression damage factor in the most unfavorable damage section was adopted as the overall damage evaluation index of the components, enabling the development of a “material-section-component” multilevel damage evaluation correlation. The evaluation results were in good agreement with those of the classic Park-Ang model. The findings provide valuable insights for structural damage assessment following seismic events.

  • Open Access

    Wooden Beam Damage Evaluation Under Bending Loading Based on the Integration of Acoustic Emission and Principal Component Analysis

    by Shenglan Ma, Shurong Ren, Zhining Chen, Chen Wu, Shaofei Jiang

    This paper proposes a comprehensive evaluation index based on the combination of acoustic emission (AE) technology and principal component analysis (PCA) to address the issue of low accuracy of any single AE parameter in identifying damage to wooden beams caused by accumulative damage. Four-point bending tests were conducted on wooden beams to monitor the process of performance degradation and evaluate damage progress. The results indicate that the proposed comprehensive evaluation index can divide the damage evolution process of wooden beams into four stages: initial compaction, elastic deformation, crack propagation, and instability fracture. These stages are consistent with the mechanical properties of wooden beams. The time of crack initiation can also be judged according to the comprehensive evaluation index value. The proposed wooden beam damage detection method based on the AE technique provides a reference for further research on the damage evolution mechanism of wooden structures and in situ monitoring methods.