Oluwadamilare Charles Adesina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Oluwadamilare Charles Adesina has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Avinaya Tripathi
Arizona State Univ
2 shared publications - Narayanan Neithalath
School of Sustainable Engineering and the Built Environment, Arizona State University, Tempe, AZ, USA
2 shared publications - Sahil Surehali
Arizona State Univ
2 shared publications - Aditya Kumar
Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO, USA
1 shared publication Brian R. Cherry
The Magnetic Resonance Research Center, Arizona State University, Tempe, AZ, USA
1 shared publicationNarayanan Neithalath
1 shared publication
Latest Publications
- Open Access
- 1 January 2027
- Published by Royal Society of Chemistry (RSC) in RSC Mechanochemistry
Processing energy-based evaluation of structural evolution in kaolinite and montmorillonite standards during mechano-chemical activation
Kinematic modeling, validated against measured milling power and energy, tracks structural and reactivity evolution in two clay minerals, yielding an efficiency index for designing energy-lean mechano-chemical processes.
- 1 January 2027
- Published by Royal Society of Chemistry (RSC) in RSC Mechanochemistry
Open AccessProcessing energy-based evaluation of structural evolution in kaolinite and montmorillonite standards during mechano-chemical activation
Kinematic modeling, validated against measured milling power and energy, tracks structural and reactivity evolution in two clay minerals, yielding an efficiency index for designing energy-lean mechano-chemical processes.
- Open Access
- 18 April 2026
- Published by Elsevier in SSRN Electronic Journal
On the Recycling of Disposed Wind Turbine Blades as Components in Regular and 3D Printed Concrete Applications: Property and Sustainability Aspects
The rapid expansion of wind energy infrastructure has created an emerging sustainability challenge—the disposal of end-of-life wind turbine blades (WTBs), which are predominantly composed of difficult-to-recycle glass fiber–reinforced polymer composites. This study addresses this challenge by systematically investigating the valorization of recycled glass fiber (rGF) and recycled glass powder (rGP) derived from decommissioned WTBs in cementitious mixtures. Four reuse strategies are examined: (i) rGF as fiber reinforcement; (ii) rGP as partial replacement of natural sand; (iii) rGP as partial replacement of ordinary Portland cement; and (iv) a combined rGF–rGP approach. Compressive strength development is evaluated along with quantitative characterization of cement hydration and hydrated phases when rGF and rGP are used. Results show that rGF enhances compressive strength (up to ~16% at 28 days) through microscale reinforcing. A performance efficiency index is used to indicate the coupled effect of strength and sustainability, which reveals rGF–rGP mixtures, unsurprisingly, as being the most efficient. Selected mixtures demonstrate adequate extrudability and buildability when employed in 3D printing applications. This study demonstrates the potential of recycled wind turbine blade wastes to be sustainably used in low-carbon concrete mixtures and for novel applications including 3D printing.
- 18 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessOn the Recycling of Disposed Wind Turbine Blades as Components in Regular and 3D Printed Concrete Applications: Property and Sustainability Aspects
The rapid expansion of wind energy infrastructure has created an emerging sustainability challenge—the disposal of end-of-life wind turbine blades (WTBs), which are predominantly composed of difficult-to-recycle glass fiber–reinforced polymer composites. This study addresses this challenge by systematically investigating the valorization of recycled glass fiber (rGF) and recycled glass powder (rGP) derived from decommissioned WTBs in cementitious mixtures. Four reuse strategies are examined: (i) rGF as fiber reinforcement; (ii) rGP as partial replacement of natural sand; (iii) rGP as partial replacement of ordinary Portland cement; and (iv) a combined rGF–rGP approach. Compressive strength development is evaluated along with quantitative characterization of cement hydration and hydrated phases when rGF and rGP are used. Results show that rGF enhances compressive strength (up to ~16% at 28 days) through microscale reinforcing. A performance efficiency index is used to indicate the coupled effect of strength and sustainability, which reveals rGF–rGP mixtures, unsurprisingly, as being the most efficient. Selected mixtures demonstrate adequate extrudability and buildability when employed in 3D printing applications. This study demonstrates the potential of recycled wind turbine blade wastes to be sustainably used in low-carbon concrete mixtures and for novel applications including 3D printing.