Shailendra P. Joshi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shailendra P. Joshi has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
Padmeya P. Indurkar
National University of Singapore
3 shared publicationsShahmeer Baweja
University of Houston
3 shared publicationsShowren Datta
Department of Mechanical and Aerospace Engineering University of Houston Houston 77204 TX
3 shared publications- Ahmed Amine Benzerga
Department of Aerospace Engineering, Texas A&M University, College Station, USA
2 shared publications - Padmeya Prashant Indurkar
Department of Mechanical Engineering,National University of Singapore,Singapore 117576, Singapore
2 shared publications A.A. Benzerga
1 shared publication
Latest Publications
- Open Access
- 25 June 2026
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 339
A comparison of mechanism-based plasticity models for polycrystalline magnesium alloys
- 25 June 2026
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 339
Open AccessA comparison of mechanism-based plasticity models for polycrystalline magnesium alloys
- Open Access
An assessment of mechanism-based plasticity models for polycrystalline magnesium alloys
The objective of this work is to assess computationally efficient coarse-grained plasticity models against high-fidelity crystal plasticity simulations for magnesium polycrystals over a wide range of textures and grain sizes. A basic requirement is that such models are able to capture {\it evolving} plastic anisotropy and tension-compression asymmetry. To this end, two-surface and three-surface plasticity models are considered. The two-surface constitutive formulation separately accounts for slip and twinning, while the three-surface model further apportions the contributions of basal and nonbasal slip. Model identification is based on stress-strain responses for loading along six orientations under both tension and compression. The evolution of overall plastic anisotropy, as well as microscale relative activities of slip and twin systems, is analyzed in detail. The prospects of using coarse-grained plasticity models in guiding the development of physically sound damage models for magnesium alloys are discussed.
Open AccessAn assessment of mechanism-based plasticity models for polycrystalline magnesium alloys
The objective of this work is to assess computationally efficient coarse-grained plasticity models against high-fidelity crystal plasticity simulations for magnesium polycrystals over a wide range of textures and grain sizes. A basic requirement is that such models are able to capture {\it evolving} plastic anisotropy and tension-compression asymmetry. To this end, two-surface and three-surface plasticity models are considered. The two-surface constitutive formulation separately accounts for slip and twinning, while the three-surface model further apportions the contributions of basal and nonbasal slip. Model identification is based on stress-strain responses for loading along six orientations under both tension and compression. The evolution of overall plastic anisotropy, as well as microscale relative activities of slip and twin systems, is analyzed in detail. The prospects of using coarse-grained plasticity models in guiding the development of physically sound damage models for magnesium alloys are discussed.
- Open Access
- 2 July 2024
- Published by Springer Nature in International Journal of Fracture
- Vol. 247 (2) , 1-2
Introduction to the special issue on structural integrity
- 2 July 2024
- Published by Springer Nature in International Journal of Fracture
- Vol. 247 (2) , 1-2
Open AccessIntroduction to the special issue on structural integrity
- 5 April 2024
- Published by Springer Nature in International Journal of Fracture
- Vol. 247 (2) , 167-182
Void growth and coalescence in sigmoidal hardening porous plastic solids under tensile and shear loading
- 5 April 2024
- Published by Springer Nature in International Journal of Fracture
- Vol. 247 (2) , 167-182
Void growth and coalescence in sigmoidal hardening porous plastic solids under tensile and shear loading
- 10 February 2024
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 185
Viscoelastic mechanics of two-dimensional granular lattices
- 10 February 2024
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 185
Viscoelastic mechanics of two-dimensional granular lattices
- Open Access
- 1 October 2023
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 11 (10) , 3657-3672
Three-dimensional computational characterization of grain size and texture effects in magnesium alloys
- 1 October 2023
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 11 (10) , 3657-3672
Open AccessThree-dimensional computational characterization of grain size and texture effects in magnesium alloys
- Open Access
- 8 June 2023
- Published by Springer Nature in Research Square
Void Growth and Coalescence in Sigmoidal Hardening Porous Plastic Solids under Tensile and Shear Loading
This work examines the void growth and coalescence in isotropic porous elastoplastic solids with sigmoidal material hardening via finite element three-dimensional unit cell calculations. The investigations are carried out for various combinations of stress triaxiality ratio T and Lode parameter L and considers a wide range of sigmoidal hardening behaviors with effective hardening rates spanning two decades. The effect of L is considered in the presence and in the absence of imposed shear stress. Our findings reveal that depending on the rate of sigmoidal hardening the cell stress-strain responses may exhibit two distinct transitions with respect to stress triaxiality T. Further, the sigmoidal hardening rate also influences porosity evolution which may show stagnation before a runaway growth up to final failure. For a given T-L combination, an imposed shear stress exacerbates the onset of coalescence relative to its counterpart with no imposed shear stress. We find that the residual cell ductility beyond the onset of coalescence is strongly influenced by the effective material hardening rate at high triaxiality levels. Mathematics Subject Classification (2020) MSC code1 · MSC code2 · more
- 8 June 2023
- Published by Springer Nature in Research Square
Open AccessVoid Growth and Coalescence in Sigmoidal Hardening Porous Plastic Solids under Tensile and Shear Loading
This work examines the void growth and coalescence in isotropic porous elastoplastic solids with sigmoidal material hardening via finite element three-dimensional unit cell calculations. The investigations are carried out for various combinations of stress triaxiality ratio T and Lode parameter L and considers a wide range of sigmoidal hardening behaviors with effective hardening rates spanning two decades. The effect of L is considered in the presence and in the absence of imposed shear stress. Our findings reveal that depending on the rate of sigmoidal hardening the cell stress-strain responses may exhibit two distinct transitions with respect to stress triaxiality T. Further, the sigmoidal hardening rate also influences porosity evolution which may show stagnation before a runaway growth up to final failure. For a given T-L combination, an imposed shear stress exacerbates the onset of coalescence relative to its counterpart with no imposed shear stress. We find that the residual cell ductility beyond the onset of coalescence is strongly influenced by the effective material hardening rate at high triaxiality levels. Mathematics Subject Classification (2020) MSC code1 · MSC code2 · more
- 18 May 2022
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 165
On the micromechanics of voids in nanotwinned materials
- 18 May 2022
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 165
On the micromechanics of voids in nanotwinned materials
- Open Access
- 16 July 2021
- Published by ASME International
On the Role of Crystallographic Anisotropy and Texture in Damage Tolerance of Hexagonal Materials
Division / Sponsors: Aerospace, Bioengineering, Applied Mechanics, Design Engineering Division, Advanced Energy Systems, Manufacturing Engineering Division, Noise Control and Acoustics, Nondestructive Evaluation, Diagnosis, and Prognosis (NDPD), Nuclear Engineering Division, Process Industries Division, Fluids Engineering, Heat Transfer, Materials, Microelectromechanical Systems, Safety Engineering and Risk Analysis, Computers & Information in Engineering
- 16 July 2021
- Published by ASME International
Open AccessOn the Role of Crystallographic Anisotropy and Texture in Damage Tolerance of Hexagonal Materials
Division / Sponsors: Aerospace, Bioengineering, Applied Mechanics, Design Engineering Division, Advanced Energy Systems, Manufacturing Engineering Division, Noise Control and Acoustics, Nondestructive Evaluation, Diagnosis, and Prognosis (NDPD), Nuclear Engineering Division, Process Industries Division, Fluids Engineering, Heat Transfer, Materials, Microelectromechanical Systems, Safety Engineering and Risk Analysis, Computers & Information in Engineering
- 20 February 2021
- Published by Springer Nature
- p. 81-89
On the Role of Crystallographic Anisotropy and Texture in Damage Tolerance of Magnesium and Its Alloys
- 20 February 2021
- Published by Springer Nature
- p. 81-89
On the Role of Crystallographic Anisotropy and Texture in Damage Tolerance of Magnesium and Its Alloys