MMMaxwell Mamishev

Maxwell Mamishev

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Maxwell Mamishev has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Firefly: A Low-Resolution Thermal Trigger for Gated Sensor Fusion in Human–Robot Collaborative Manufacturing

    by Olga Podkorytova, Mingcheng Yang, Yancheng Chen, Maxwell Mamishev, Eric Jiang, Zheng Liu, Xueyicheng Xu, Sep Makhsous

    Automated guided vehicles and mobile robots are present on many Intelligent Manufacturing factory floors. Approximately 7.0 million U.S. workers also work on those same floors. During 2011 through 2017, forklifts caused 614 worker fatalities. Currently, no commercially available collision-avoidance sensor can manage the complexity associated with working within a plant. Therefore, fusing multiple modalities allows a system designer to gate the more expensive ones behind some minimal signal that indicates all systems should be active. Such minimal signals are expected to include body heat that even stationary personnel would have difficulty suppressing. In addition, the signal-capturing sensors ought to operate at milliwatt levels of power while keeping workers’ privacy. One type of device that has been found suitable for these requirements is a coarse thermopile array. Such a device can be fused with a rangefinder that determines distance to form a gated system. Yet the measurement capability frontier of the thermopile arrays in practical scenarios has not been explored. In addition, there is currently no figure of merit to quantify the trade-ff between induced errors and system-level power saving. In order to address these gaps, we built the fusion system, Firefly, together with a training-free detector and tested them against a human and a mannequin 1.2 to 7 m away in four thermally distinct environments, one of which is the floor of an operating factory. We found that the thermal array’s detection range varies with the environment but is predictable in a thermally uniform environment. Based on these experiments, we also proposed the Gated-Fusion Efficiency (GFE), a figure of merit that converts a trigger’s error rates into system-level power savings. Together, the capability boundary and the GFE help guide sensor-fusion system design in industrial manufacturing toward safer working environments.

  • Open Access

    AETOS: Near-Field Urban Pollution Monitoring Using a Distributed Sensor Network and Backward–Forward Lagrangian Modeling: A Fireworks Case Study at Lake Union, Seattle

    by Zheng Liu, Gokul Nathan, Xueyicheng Xu, Mingcheng Yang, Kavimitiran Pasupathi, Maxwell Mamishev, Thomas Tusty, Ernst Anderson, Sep Makhsous

    Public fireworks shows are widely used for national holiday celebrations, religious ceremonies, and sports events. However, fireworks produce short-lived atmospheric particulate matter (PM) peaks, posing a risk to spectators’ health. Every year, public fireworks shows expose over 140 million Americans to episodic transient PM2.5 peaks that exceed air quality standards by up to 10 times in the United States alone. Yet the magnitude and timing of this representativeness gap have not been measured within an event. This paper investigates the Independence Day fireworks display over Lake Union, Seattle, WA, USA, using a low-cost PM network deployed up to 2 km from the launch site. We evaluated the network observations against routine monitoring data from regulatory stations within 10 km of the launch site and generated a backward–forward Lagrangian stochastic dispersion model, calibrated with the network. Spectator zone PM2.5 concentrations varied by over threefold across sensors within 1.5 km. Duration above the World Health Organization (WHO) 24 h PM2.5 guideline concentration level at network sensors varied from 1 min to nearly 30 min, and regulatory hourly averaging retained 57% of the near-field peak signal on average and only 22% in the worst case. Peak detection at some regulatory stations was delayed by one to two hours compared with the network. The dispersion model, using only network data and public regional wind data, captured the launch site location to within ~100 m and provided minute-scale estimates of PM2.5 and PM1 concentrations across the spectator zone. The findings demonstrate and quantify, for a single event, the representativeness gap expected when transient near-field fireworks plumes are evaluated using spatially sparse and hourly averaged regulatory observations.


  • Open Access

    Spill-O-Not: A contactless material level indicator for visually impaired users

    by Maxwell Mamishev, Nir Pechuk, Rayhan Shaik, Braden Miller

    The danger of incorrect pouring of hot or sticky liquids is a constant daily safety threat for 295 million visually impaired individuals around the world. Conventional dip-probe liquid level sensors have metal contacts that are exposed to corrosion and require frequent cleaning. As a result, conventional dip-probe liquid level sensors often require replacement and incur recurring maintenance costs, which reduces the long-term usability and safety of these sensors for visually impaired users. This paper presents Spill-O-Not, a portable device that utilizes a miniature Light Detection and Ranging (LiDAR) Time of Flight (ToF) sensor and integrated audio feedback to alert users when the material reaches an adjustable fill height. The fact that the sensor is contactless and allows Spill-O-Not to sit on top of the rim of the container represents a significant improvement over traditional contact-based liquid level indicators. In the 48 controlled laboratory trials using various conductive, non-conductive, and particulate materials, Spill-O-Not prevented all overflows, while maintaining a mean absolute percentage error of liquid level measurement accuracy 4.7%. The authors believe that the demonstrated low-cost sensing technology and inclusive design can significantly improve the safety and independence of millions of visually impaired users.