Xinyan Wang
Research Subjects
Xinyan Wang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Anhua Xu
Qinghai Provincial Key Laboratory of Tibet Plateau Highway Construction and Maintenance Technology, Qinghai Polytechnic University, Xining 810003, China
2 shared publications - Huaxin Chen
School of Materials Science and Engineering, Chang’an University, Xi’an 710064, China
2 shared publications - Laifa Wang
Qinghai Provincial Traffic Control Construction Engineering Group Co., Ltd., Xining 810021, China
2 shared publications - Chenglong Li
Qinghai Provincial Traffic Control Construction Engineering Group Co., Ltd., Xining 810021, China
1 shared publication - Huiting Jia
School of Materials Science and Engineering, Chang’an University, Xi’an 710061, China
1 shared publication - Suining Zheng
School of Materials Science and Engineering, Chang’an University, Xi’an 710061, China
1 shared publication
Latest Publications
- Open Access
Effect of a CaO–SiO2–Al2O3 Composite Early-Strength Agent on the Early Mechanical Properties of Cement-Based Repair Materials
The early mechanical performance of cement-based repair materials is critical for the rapid rehabilitation of concrete structures and tunnel anchorage engineering. In this study, a reference mixture (ROA) without any accelerator, a general early-strength agent (GEA) based on aluminum sulfate, and a composite early-strength agent (CEA) composed of CaO–SiO2–Al2O3 were comparatively investigated. The effects on setting time, compressive strength, flexural bond strength, and early drying shrinkage were systematically evaluated. The degree of hydration (DoH) was determined by the chemically bound water method, and the microstructure was characterized by scanning electron microscopy (SEM). The results show that CEA significantly shortened the setting time, with a final setting time of only 9.5 min, representing a 55.2% reduction compared with ROA. At 4 h, the compressive strength of CEA was 5.2% and 16.7% higher than those of GEA and ROA, respectively; at 1 d, the corresponding increases were 6.8% and 25.0%; and no strength regression was observed at 28 d. The 1 d flexural bond strength of CEA reached 6.85 MPa, 62.8% higher than that of ROA. Moreover, CEA effectively reduced early drying shrinkage, with the 7 d shrinkage rate being 18.6% lower than that of ROA. The DoH of CEA at 1 d reached 68.5%, 32.3 percentage points higher than that of ROA. SEM observations revealed that CEA promoted the formation of needle-like ettringite (AFt) crystals that interlocked in a random three-dimensional network, with calcium silicate hydrate (C–S–H) gel filling the interstices, resulting in a dense microstructure. These findings provide a systematic theoretical basis for the design of high-performance cement-based repair materials with composite early-strength agents.
Open AccessEffect of a CaO–SiO2–Al2O3 Composite Early-Strength Agent on the Early Mechanical Properties of Cement-Based Repair Materials
The early mechanical performance of cement-based repair materials is critical for the rapid rehabilitation of concrete structures and tunnel anchorage engineering. In this study, a reference mixture (ROA) without any accelerator, a general early-strength agent (GEA) based on aluminum sulfate, and a composite early-strength agent (CEA) composed of CaO–SiO2–Al2O3 were comparatively investigated. The effects on setting time, compressive strength, flexural bond strength, and early drying shrinkage were systematically evaluated. The degree of hydration (DoH) was determined by the chemically bound water method, and the microstructure was characterized by scanning electron microscopy (SEM). The results show that CEA significantly shortened the setting time, with a final setting time of only 9.5 min, representing a 55.2% reduction compared with ROA. At 4 h, the compressive strength of CEA was 5.2% and 16.7% higher than those of GEA and ROA, respectively; at 1 d, the corresponding increases were 6.8% and 25.0%; and no strength regression was observed at 28 d. The 1 d flexural bond strength of CEA reached 6.85 MPa, 62.8% higher than that of ROA. Moreover, CEA effectively reduced early drying shrinkage, with the 7 d shrinkage rate being 18.6% lower than that of ROA. The DoH of CEA at 1 d reached 68.5%, 32.3 percentage points higher than that of ROA. SEM observations revealed that CEA promoted the formation of needle-like ettringite (AFt) crystals that interlocked in a random three-dimensional network, with calcium silicate hydrate (C–S–H) gel filling the interstices, resulting in a dense microstructure. These findings provide a systematic theoretical basis for the design of high-performance cement-based repair materials with composite early-strength agents.
- Open Access
Effect of Emulsifier Type on the Properties of SBR-Modified Cement-Based Materials
Styrene butadiene rubber (SBR) is a commonly used polymer modifier that can improve the mechanical properties and durability of cement mortar. However, the effects of different emulsifier types on cement hydration behavior and structural evolution still need to be systematically studied. To clarify the differences among anionic, cationic, and nonionic SBR emulsions on mortar performance, three types of SBR emulsion were selected in this study. Setting time, chemically bound water, mechanical properties, chloride ion diffusion, freeze–thaw cycles, and microstructure were tested to evaluate the effects of different types and dosages on cement mortar. The results show that all three types of SBR emulsion prolong the setting time of cement paste and reduce the early hydration degree. The cationic SBR emulsion shows a more obvious effect. At 28 d, the compressive strength of mortar with 10% cationic SBR emulsion increases from 38.5 MPa to 41.2 MPa, and the flexural strength also increases. In terms of impermeability, the chloride ion diffusion coefficient decreases from 7.47 × 10−12 m2/s to 5.12 × 10−12 m2/s after adding 10% cationic SBR emulsion. After 100 freeze–thaw cycles, the compressive strength loss of ordinary mortar is 16%, while it decreases to 7.2% with 15% cationic SBR emulsion, and the mass loss is also reduced. Microstructural analysis shows that the modified mortar has a denser internal structure, improved interfacial continuity, and reduced crack development after freeze–thaw cycles.
Open AccessEffect of Emulsifier Type on the Properties of SBR-Modified Cement-Based Materials
Styrene butadiene rubber (SBR) is a commonly used polymer modifier that can improve the mechanical properties and durability of cement mortar. However, the effects of different emulsifier types on cement hydration behavior and structural evolution still need to be systematically studied. To clarify the differences among anionic, cationic, and nonionic SBR emulsions on mortar performance, three types of SBR emulsion were selected in this study. Setting time, chemically bound water, mechanical properties, chloride ion diffusion, freeze–thaw cycles, and microstructure were tested to evaluate the effects of different types and dosages on cement mortar. The results show that all three types of SBR emulsion prolong the setting time of cement paste and reduce the early hydration degree. The cationic SBR emulsion shows a more obvious effect. At 28 d, the compressive strength of mortar with 10% cationic SBR emulsion increases from 38.5 MPa to 41.2 MPa, and the flexural strength also increases. In terms of impermeability, the chloride ion diffusion coefficient decreases from 7.47 × 10−12 m2/s to 5.12 × 10−12 m2/s after adding 10% cationic SBR emulsion. After 100 freeze–thaw cycles, the compressive strength loss of ordinary mortar is 16%, while it decreases to 7.2% with 15% cationic SBR emulsion, and the mass loss is also reduced. Microstructural analysis shows that the modified mortar has a denser internal structure, improved interfacial continuity, and reduced crack development after freeze–thaw cycles.