Bakhtiyar Q. Khawaja Al Harki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bakhtiyar Q. Khawaja Al Harki has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ismael A. Muhammed
Department of Highway and Bridge, Technical College of Engineering, Duhok Polytechnic University, Duhok, Kurdistan Region, Iraq
2 shared publications Abdullah M. Rashed
1 shared publication- Abdullah M. Rashed
Department of Highway and Bridge, Technical College of Engineering, Duhok Polytechnic University, Duhok, Kurdistan Region, Iraq
1 shared publication - Heja Ghazi Mohamed Hasan
Department of Highway and Bridge, Technical College of Engineering, Duhok Polytechnic University, Duhok, Kurdistan Region, Iraq
1 shared publication Sherzad Waisy Khalid
1 shared publication- Ziyad Nayef Aldoski
Department of Highway and Bridge, Technical College of Engineering, Duhok Polytechnic University, 61 Zakho Road, Duhok 1006, Kurdistan Region, Iraq
1 shared publication
Latest Publications
- Open Access
- 12 July 2026
- Published by Duhok Polytechnic University in Dasinya Journal for Engineering and Informatics
- Vol. 2 (3)
Experimental Evaluation of the Mechanical Performance and Deformation Strength of Glass Fiber-Reinforced Asphalt Mixtures
In this work, the mechanical properties and deformation behavior of Hot Mix Asphalt (HMA) reinforced with Glass Fiber (GF) are analyzed. The focus was mainly on determining the effects of different GF content on the behavior/ stability/ stiffness/ permanent deformation of asphalt concrete in wearing courses. The experimental protocol was based on asphalt Al-Daurah cement (40/50 penetration grade) and crushed aggregates obtained from Kavin Company (Zakho, Duhok), with a nominal maximum aggregate size (NMAS) of 12.5 mm, as per ASTM D3515. The study was carried out in two stages. The Optimum Asphalt Content (O.A.C.) was determined to be 5.1% using Marshall mix techniques. In phase two, 5 mixtures were made together with the dry mixing method, adding (GF) at 0% (Control), 0.3%, 0.5%, 0.7%, and 0.9% by weight of the mix. Experimental results showed improved structural integrity of the asphalt when glass fibers were applied. The Marshall Stability was at its maximum at 0.5 % GF (12.5 kN), 25 % higher than the control mixture. Additionally, the Kim Test was used to probe the high-temperature effect, and the Deformation Strength (SD) level increased by ≈ 50% at the same dosage (2.706 MPa > 4.048 MPa). The maximum Marshall Stiffness was 3.8 kN/mm at 0.5% GF, indicating superior shear resistance. Yet, fiber levels above 0.5% lead to decreased performance due to fiber agglomeration and poor workability. The Optimum Glass Fiber Content (O.GF.C.) is 0.5% GF for improving both the durability and rutting resistance of flexible pavements in hot weather.
- 12 July 2026
- Published by Duhok Polytechnic University in Dasinya Journal for Engineering and Informatics
- Vol. 2 (3)
Open AccessExperimental Evaluation of the Mechanical Performance and Deformation Strength of Glass Fiber-Reinforced Asphalt Mixtures
In this work, the mechanical properties and deformation behavior of Hot Mix Asphalt (HMA) reinforced with Glass Fiber (GF) are analyzed. The focus was mainly on determining the effects of different GF content on the behavior/ stability/ stiffness/ permanent deformation of asphalt concrete in wearing courses. The experimental protocol was based on asphalt Al-Daurah cement (40/50 penetration grade) and crushed aggregates obtained from Kavin Company (Zakho, Duhok), with a nominal maximum aggregate size (NMAS) of 12.5 mm, as per ASTM D3515. The study was carried out in two stages. The Optimum Asphalt Content (O.A.C.) was determined to be 5.1% using Marshall mix techniques. In phase two, 5 mixtures were made together with the dry mixing method, adding (GF) at 0% (Control), 0.3%, 0.5%, 0.7%, and 0.9% by weight of the mix. Experimental results showed improved structural integrity of the asphalt when glass fibers were applied. The Marshall Stability was at its maximum at 0.5 % GF (12.5 kN), 25 % higher than the control mixture. Additionally, the Kim Test was used to probe the high-temperature effect, and the Deformation Strength (SD) level increased by ≈ 50% at the same dosage (2.706 MPa > 4.048 MPa). The maximum Marshall Stiffness was 3.8 kN/mm at 0.5% GF, indicating superior shear resistance. Yet, fiber levels above 0.5% lead to decreased performance due to fiber agglomeration and poor workability. The Optimum Glass Fiber Content (O.GF.C.) is 0.5% GF for improving both the durability and rutting resistance of flexible pavements in hot weather.
- Open Access
- 12 April 2026
- Published by Duhok Polytechnic University in Dasinya Journal for Engineering and Informatics
- Vol. 2 (2)
Mechanical Performance of Asphalt Mixtures Reinforced with Polypropylene Fibers
Plastic waste is a new environmental threat and potential resource at the same time. The use of plastic waste polymer polypropylene fibers in asphalt mixtures is a good eco-solution that increases the pavement's lifetime. With traffic rising, forcing the needs in classic asphalt for improved durability. The study aimed to investigate the reinforcement characteristics of plastic fibers of four different lengths in cm (FL1, FL2, FL3, and FL4), represented by 1 cm, 2 cm, 3 cm, and 4 cm, added to virgin asphalt mixtures (0.3% by total mix). Results by Marshall stability, Marshall stiffness, indirect tensile strength (ITS), moisture susceptibility (TSR), and deformation strength testing were quantified. The results showed that the stability of Marshall increased until the FL3 length, with FL1 and FL2 showing 23% and 10% enhancement, respectively, followed by a marginal decrease to FL4 as plastic fiber was introduced. Additionally, the moisture resistance improved with the fiber length, and the TSR values were significantly higher than that of the virgin mix. Regarding rutting resistance, fiber reinforcements greatly lowered deformation, most especially when fiber lengths were shorter. Generally, durability, moisture damage resistance, and rutting resistance are enhanced on a scale of 1–2 cm fiber length, hence being the most convenient quality for asphalt mixtures. In this research, the optimum length of PP fiber was specified to improve mechanical properties, and plastic waste was reused as a resource for sustainable road construction, both in accordance with SDG 9 and SDG 12 of the Sustainable Development Goals.
- 12 April 2026
- Published by Duhok Polytechnic University in Dasinya Journal for Engineering and Informatics
- Vol. 2 (2)
Open AccessMechanical Performance of Asphalt Mixtures Reinforced with Polypropylene Fibers
Plastic waste is a new environmental threat and potential resource at the same time. The use of plastic waste polymer polypropylene fibers in asphalt mixtures is a good eco-solution that increases the pavement's lifetime. With traffic rising, forcing the needs in classic asphalt for improved durability. The study aimed to investigate the reinforcement characteristics of plastic fibers of four different lengths in cm (FL1, FL2, FL3, and FL4), represented by 1 cm, 2 cm, 3 cm, and 4 cm, added to virgin asphalt mixtures (0.3% by total mix). Results by Marshall stability, Marshall stiffness, indirect tensile strength (ITS), moisture susceptibility (TSR), and deformation strength testing were quantified. The results showed that the stability of Marshall increased until the FL3 length, with FL1 and FL2 showing 23% and 10% enhancement, respectively, followed by a marginal decrease to FL4 as plastic fiber was introduced. Additionally, the moisture resistance improved with the fiber length, and the TSR values were significantly higher than that of the virgin mix. Regarding rutting resistance, fiber reinforcements greatly lowered deformation, most especially when fiber lengths were shorter. Generally, durability, moisture damage resistance, and rutting resistance are enhanced on a scale of 1–2 cm fiber length, hence being the most convenient quality for asphalt mixtures. In this research, the optimum length of PP fiber was specified to improve mechanical properties, and plastic waste was reused as a resource for sustainable road construction, both in accordance with SDG 9 and SDG 12 of the Sustainable Development Goals.