Oto Melter
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Oto Melter has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- David Čítek
Klokner Institute, Czech Technical University in Prague, 166 08 Prague, Czech Republic
2 shared publications - Katarzyna Ewa Buczkowska
Faculty of Mechanical Engineering, Technical University of Liberec, 461 17 Liberec, Czech Republic
2 shared publications - Petr Zelený
Faculty of Mechanical Engineering, Technical University of Liberec, 461 17 Liberec, Czech Republic
2 shared publications - Piotr Łoś
Polytechnic Faculty, University of Kalisz, Pl. Wojciecha Bogusławskiego 2, 62-800 Kalisz, Poland
2 shared publications - Vladislav Bureš
Faculty of Arts and Architecture, Technical University of Liberec, 461 17 Liberec, Czech Republic
2 shared publications - Vojtěch Jan Stoklasa
Faculty of Arts and Architecture, Technical University of Liberec, 461 17 Liberec, Czech Republic
2 shared publications
Latest Publications
- Open Access
3D-Printed Geopolymer Composite Truss Beam: Experimental Verification of Manufacturing and Load-Bearing Capacity in Four-Point Bending
Geopolymers represent a promising material platform for extrusion-based 3D printing; however, current research remains largely focused on mix design, rheology, printability, buildability, and the relationship between process parameters and the resulting microstructure. This article therefore compares the behaviour of two 3D-printed geopolymer composite truss beams with reference cementitious composite beams developed within the 3D STAR project. The geopolymer elements, 2932 mm long, were designed for the same material volume and target geometry as the reference CC element; however, because of mixture spreading, they reached cross-sections of only approximately 140/250 mm and 170/250 mm. The first beam was printed without setting acceleration, while the second was locally treated with a hot-air gun. In four-point bending, GC-2 was loaded first and reached 22 kN, while GC-1 was loaded second and reached 29 kN; the reference cementitious beams reached 31 and 40 kN. The CC elements failed by rupture of the tensile reinforcement, while the GC elements failed by joint failure followed by deformation and local disintegration of the composite. The study thus shows that the main difference between the two systems lies not only in the achieved load-bearing capacity, but also in stiffness, the shape of the load-displacement diagrams, and the failure mechanism.
Open Access3D-Printed Geopolymer Composite Truss Beam: Experimental Verification of Manufacturing and Load-Bearing Capacity in Four-Point Bending
Geopolymers represent a promising material platform for extrusion-based 3D printing; however, current research remains largely focused on mix design, rheology, printability, buildability, and the relationship between process parameters and the resulting microstructure. This article therefore compares the behaviour of two 3D-printed geopolymer composite truss beams with reference cementitious composite beams developed within the 3D STAR project. The geopolymer elements, 2932 mm long, were designed for the same material volume and target geometry as the reference CC element; however, because of mixture spreading, they reached cross-sections of only approximately 140/250 mm and 170/250 mm. The first beam was printed without setting acceleration, while the second was locally treated with a hot-air gun. In four-point bending, GC-2 was loaded first and reached 22 kN, while GC-1 was loaded second and reached 29 kN; the reference cementitious beams reached 31 and 40 kN. The CC elements failed by rupture of the tensile reinforcement, while the GC elements failed by joint failure followed by deformation and local disintegration of the composite. The study thus shows that the main difference between the two systems lies not only in the achieved load-bearing capacity, but also in stiffness, the shape of the load-displacement diagrams, and the failure mechanism.
- Open Access
- 10 July 2026
- Published by MDPI AG in Preprints.org
3D‐Printed Geopolymer Composite Truss Beam: Experimental Verification of Manufacturing and Load‐Bearing Capacity in Four‐Point Bending
Geopolymers represent a promising material platform for extrusion-based 3D printing; however, current research remains largely focused on mix design, rheology, printability, buildability, and the relationship between process parameters and the resulting microstructure (1–7). This article therefore compares the behaviour of two 3D-printed geopolymer composite truss beams with reference cementitious composite beams developed within the 3D STAR project (8). The geopolymer elements, 2932 mm long, were designed for the same material volume and target geometry as the reference CC element; however, because of mixture spreading, they reached cross-sections of only approximately 140/250 mm and 170/250 mm. The first beam was printed without setting acceleration, while the second was locally treated with a hot-air gun. In four-point bending, the geopolymer beams reached maximum forces of 22 and 29 kN, whereas the reference cementitious beams reached 31 and 40 kN. The CC elements failed by rupture of the tensile reinforcement, while the GC elements failed by joint failure followed by deformation and local disintegration of the composite. The study thus shows that the main difference between the two systems lies not only in the achieved load-bearing capacity, but also in stiffness, the shape of the load-displacement diagrams, and the failure mechanism.
- 10 July 2026
- Published by MDPI AG in Preprints.org
Open Access3D‐Printed Geopolymer Composite Truss Beam: Experimental Verification of Manufacturing and Load‐Bearing Capacity in Four‐Point Bending
Geopolymers represent a promising material platform for extrusion-based 3D printing; however, current research remains largely focused on mix design, rheology, printability, buildability, and the relationship between process parameters and the resulting microstructure (1–7). This article therefore compares the behaviour of two 3D-printed geopolymer composite truss beams with reference cementitious composite beams developed within the 3D STAR project (8). The geopolymer elements, 2932 mm long, were designed for the same material volume and target geometry as the reference CC element; however, because of mixture spreading, they reached cross-sections of only approximately 140/250 mm and 170/250 mm. The first beam was printed without setting acceleration, while the second was locally treated with a hot-air gun. In four-point bending, the geopolymer beams reached maximum forces of 22 and 29 kN, whereas the reference cementitious beams reached 31 and 40 kN. The CC elements failed by rupture of the tensile reinforcement, while the GC elements failed by joint failure followed by deformation and local disintegration of the composite. The study thus shows that the main difference between the two systems lies not only in the achieved load-bearing capacity, but also in stiffness, the shape of the load-displacement diagrams, and the failure mechanism.
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Advances in Science and Technology
- Vol. 176, 133-140
3D Printed Portal: Concrete, Digital Geometry and the Redefinition of the Building Element
The paper presents a research object of a portal realized using the method of 3D printing of cement composite. The object serves as an experimental portal redefining the relationship between a building element and ornament. The form of the portal is generated by a Möbius transformation of part of the load-bearing wall. This transformation allows the basic structural logic of the wall to be converted into an ornamental layer without losing material logic and continuity. The load-bearing material of the object is a cement composite, optimized for robotic printing without formwork. Printing enabled the production of complex elements with high geometric precision. Thanks to digital control, the shape can be deconstructed into a precise printing trajectory, eliminating the human factor and streamlining production even for complex segments. The resulting object combines the structural and visual roles of the elements without the need for secondary division into load-bearing and aesthetic parts. The aim of the research is to verify the possibilities of robotic printing in the production of architectural elements from cement composite that transcend the traditional dichotomy of structure and decoration. The process shows that even highly individualized elements can be produced efficiently, repeatedly, and with material savings. Special attention is paid to detailed parameterization of the mold, surface quality, and layering during printing, which fundamentally affects the resulting mechanical and aesthetic properties. The paper offers a practical view of the application of robotic 3D concrete printing in architectural and engineering applications and its potential for transforming current construction approaches.
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Advances in Science and Technology
- Vol. 176, 133-140
3D Printed Portal: Concrete, Digital Geometry and the Redefinition of the Building Element
The paper presents a research object of a portal realized using the method of 3D printing of cement composite. The object serves as an experimental portal redefining the relationship between a building element and ornament. The form of the portal is generated by a Möbius transformation of part of the load-bearing wall. This transformation allows the basic structural logic of the wall to be converted into an ornamental layer without losing material logic and continuity. The load-bearing material of the object is a cement composite, optimized for robotic printing without formwork. Printing enabled the production of complex elements with high geometric precision. Thanks to digital control, the shape can be deconstructed into a precise printing trajectory, eliminating the human factor and streamlining production even for complex segments. The resulting object combines the structural and visual roles of the elements without the need for secondary division into load-bearing and aesthetic parts. The aim of the research is to verify the possibilities of robotic printing in the production of architectural elements from cement composite that transcend the traditional dichotomy of structure and decoration. The process shows that even highly individualized elements can be produced efficiently, repeatedly, and with material savings. Special attention is paid to detailed parameterization of the mold, surface quality, and layering during printing, which fundamentally affects the resulting mechanical and aesthetic properties. The paper offers a practical view of the application of robotic 3D concrete printing in architectural and engineering applications and its potential for transforming current construction approaches.