Luciano Pianese
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Luciano Pianese has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Alessandro De Luca
Department of Engineering, University of Campania “L. Vanvitelli”, Via Roma 29, 81031 Aversa, Italy
3 shared publications - Agnese Coscetta
Department of Engineering, University of Campania “Luigi Vanvitelli”, 80131 Aversa, Italy
2 shared publications - Aldo Minardo
Universit della Campania Luigi Vanvitelli, Aversa, ITALY
2 shared publications - Donato Perfetto
Department of Engineering, University of Campania “Luigi Vanvitelli”, 81031 Aversa, Italy
2 shared publications - Ester Catalano
Department of Engineering, University of Campania “Luigi Vanvitelli”, 80131 Aversa, Italy
2 shared publications - Francesco Caputo
Department of Engineering, University of Campania “L. Vanvitelli”, Via Roma 29, 81031 Aversa, Italy
2 shared publications
Latest Publications
- Open Access
- 1 August 2026
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 31 (8)
Investigation of propagation mechanisms under compressive fatigue loads of LVI damage in CFRP coupons using ultrasonic guided waves
The damage tolerance approach enables the design of lightweight composite structures, provided that damage progression remains controlled throughout their operational life. However, delamination growth under fatigue loads, particularly for low-velocity impact (LVI)-induced damage, remains poorly understood. The no-growth design philosophy assumes that delaminations in the high-cycle fatigue regime exhibit an extended plateau phase, during which no significant propagation is observed. Nevertheless, recent studies suggest that this plateau phase may result from the limitations of conventional inspection techniques (i.e. C-SCAN), rather than from an actual absence of damage evolution. In particular, C-SCAN-based ultrasonic inspections, typically used for the scope, may fail to detect internal delaminations encapsulated within outer ones due to the shadowing effect, leading to an underestimation of fatigue-driven damage progression. This raises concerns regarding the reliability of traditional non-destructive evaluation (NDE) methods for monitoring damage in critical composite structures. As part of the TU-LEARN (Structural Life Extension Enhanced by Artificial Intelligence) project, funded by Unione Europea – Next Generation EU, under the PRIN 2022 PNRR – D.D. n. 1409 del 14-09-2022 program, this study aims to enhance the understanding of LVI damage propagation mechanisms under fatigue loading. An experimental campaign was conducted on Carbon Fibre Reinforced Polymer (CFRP) coupons with a stacking sequence of [(45,-45,90,0)]2s, representative of aerospace-grade laminates. The test protocol included LVI tests in accordance with ASTM D7136 standard, followed by compression after impact (CAI) fatigue tests as per ASTM D7137 standard, to assess the residual strength and progressive damage evolution under cyclic loading. Impact tests were performed using an energy level of 15 J, with a drop mass of 4.567 kg, ensuring a representative damage state. Subsequently, fatigue tests were conducted under compressive-compressive loading with a stress ratio of R = 0.1 and a fatigue load frequency of f = 4 Hz. To monitor damage evolution at multiple fatigue stages, an ultrasonic guided wave (UGW)-based Structural Health Monitoring (SHM) system was integrated into the test campaign, complementing C-SCAN ultrasonic inspections. UGW signals were acquired in a pitch–catch configurationusing surface-bonded piezoelectric (PZT) transducers: at each inspection stop, a repeatable tone-burst excitation was applied to the actuator, and the received waveforms were recorded on selected sensing paths (with signal averaging to improve the signal-to-noise ratio). Damage Indexes (DIs) were then computed by comparing each acquired signal to an undamaged baseline to quantify damage-induced changes. This approach provided a more detailed assessment of delamination growth throughout the fatigue life, revealing potential limitations in the conventional no-growth assumption, Figure 1. The use of UGW-SHM appeared capable of tracking the internal damage progression, even in regions where C-SCAN technique was insufficient.
- 1 August 2026
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 31 (8)
Open AccessInvestigation of propagation mechanisms under compressive fatigue loads of LVI damage in CFRP coupons using ultrasonic guided waves
The damage tolerance approach enables the design of lightweight composite structures, provided that damage progression remains controlled throughout their operational life. However, delamination growth under fatigue loads, particularly for low-velocity impact (LVI)-induced damage, remains poorly understood. The no-growth design philosophy assumes that delaminations in the high-cycle fatigue regime exhibit an extended plateau phase, during which no significant propagation is observed. Nevertheless, recent studies suggest that this plateau phase may result from the limitations of conventional inspection techniques (i.e. C-SCAN), rather than from an actual absence of damage evolution. In particular, C-SCAN-based ultrasonic inspections, typically used for the scope, may fail to detect internal delaminations encapsulated within outer ones due to the shadowing effect, leading to an underestimation of fatigue-driven damage progression. This raises concerns regarding the reliability of traditional non-destructive evaluation (NDE) methods for monitoring damage in critical composite structures. As part of the TU-LEARN (Structural Life Extension Enhanced by Artificial Intelligence) project, funded by Unione Europea – Next Generation EU, under the PRIN 2022 PNRR – D.D. n. 1409 del 14-09-2022 program, this study aims to enhance the understanding of LVI damage propagation mechanisms under fatigue loading. An experimental campaign was conducted on Carbon Fibre Reinforced Polymer (CFRP) coupons with a stacking sequence of [(45,-45,90,0)]2s, representative of aerospace-grade laminates. The test protocol included LVI tests in accordance with ASTM D7136 standard, followed by compression after impact (CAI) fatigue tests as per ASTM D7137 standard, to assess the residual strength and progressive damage evolution under cyclic loading. Impact tests were performed using an energy level of 15 J, with a drop mass of 4.567 kg, ensuring a representative damage state. Subsequently, fatigue tests were conducted under compressive-compressive loading with a stress ratio of R = 0.1 and a fatigue load frequency of f = 4 Hz. To monitor damage evolution at multiple fatigue stages, an ultrasonic guided wave (UGW)-based Structural Health Monitoring (SHM) system was integrated into the test campaign, complementing C-SCAN ultrasonic inspections. UGW signals were acquired in a pitch–catch configurationusing surface-bonded piezoelectric (PZT) transducers: at each inspection stop, a repeatable tone-burst excitation was applied to the actuator, and the received waveforms were recorded on selected sensing paths (with signal averaging to improve the signal-to-noise ratio). Damage Indexes (DIs) were then computed by comparing each acquired signal to an undamaged baseline to quantify damage-induced changes. This approach provided a more detailed assessment of delamination growth throughout the fatigue life, revealing potential limitations in the conventional no-growth assumption, Figure 1. The use of UGW-SHM appeared capable of tracking the internal damage progression, even in regions where C-SCAN technique was insufficient.
- Open Access
- 1 August 2026
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 31 (8)
Investigation of the strain evolution in CFRP coupons subjected to LVI impact and compressive fatigue loads by distributed optical fiber sensors
Composite structures made of CFRPs are increasingly adopted in aerospace and high-performance engineering applications due to their superior strength-to-weight ratio and excellent fatigue resistance. However, their susceptibility to barely visible impact damage (BVID), especially following Low Velocity Impact (LVI) events, remains a critical challenge in structural integrity management. These damages, often invisible on the surface, can lead to internal delaminations that compromise long-term performance under cyclic loading conditions. To address this challenge, Structural Health Monitoring (SHM) systems have been increasingly adopted in aerospace and engineering fields. One of the most promising methods for SHM involves the use of distributed fiber optic sensors (DFOS), in virtue of their low size, light weight, high sensitivity and the ability to detect small strain changes, which makes them particularly effective in monitoring the early stages of damage progression. As part of the TU-LEARN (Structural Life Extension Enhanced by Artificial Intelligence) project, funded by Unione Europea – Next Generation EU, under the PRIN 2022 PNRR – D.D. n. 1409 del 14-09-2022 program, this study investigates the fatigue-driven progression of LVI-induced damage using a Brillouin Optical Frequency-Domain Analysis (BOFDA) system capable of distributed strain measurements with 8-mm spatial resolution. The experimental investigation was conducted on multiple CFRP specimens with nominal dimensions of 100 mm × 150 mm × 2.7 mm. All laminates featured a symmetrical stacking sequence of [(45/−45/90/0)]₂s. For DFOS measurements, a polyimide-coated optical fiber with an outer diameter of 145 μm was bonded to the surface of each specimen, as highlighted in orange in Fig. 1(a). Additionally, six PZT transducers were surface-mounted in a 2×3 array near the central area of each panel, to realize ultrasonic guided wave (UGW) investigation along multiple directions. Each specimen was impacted at its planar center with an energy level of 15 J using a StepLab DW 2000 drop tower. Then, a compressive-compressive fatigue loading was applied under cyclic conditions (stress ratio R = 0.1, fatigue load frequency f = 4 Hz), using a StepLab Dynamic UD040. In the pristine state, after the impact and at predetermined interruption points of the fatigue load, damage growth was tracked using BOFDA strain maps for 3 different compression loads (L = 5 kN, L = 10 kN, L = 15 kN), as well as UGW-based signal analysis across all actuator-receiver combinations. As an example, we show in Figure 1(b) the strain profiles acquired via our BOFDA sensor, under a constant compressive load of 5 kN and at various fatigue stages. The acquired profiles show a gradual increase in the compressive strain levels, compatible with the delamination growth and consequent stiffness degradation of the laminate. Some acceleration in the strain increase was observed when passing from 800k to 1000k fatigue cycles, i.e. in proximity of the panel failure occurred after 1010k cycles. Similar results, obtained on other panels and with different compressive loads, indicate that the high-resolution strain field measurements provided by BOFDA sensors are effective in indicating internal damage progression in CFRP panels subjected to cyclic loading.
- 1 August 2026
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 31 (8)
Open AccessInvestigation of the strain evolution in CFRP coupons subjected to LVI impact and compressive fatigue loads by distributed optical fiber sensors
Composite structures made of CFRPs are increasingly adopted in aerospace and high-performance engineering applications due to their superior strength-to-weight ratio and excellent fatigue resistance. However, their susceptibility to barely visible impact damage (BVID), especially following Low Velocity Impact (LVI) events, remains a critical challenge in structural integrity management. These damages, often invisible on the surface, can lead to internal delaminations that compromise long-term performance under cyclic loading conditions. To address this challenge, Structural Health Monitoring (SHM) systems have been increasingly adopted in aerospace and engineering fields. One of the most promising methods for SHM involves the use of distributed fiber optic sensors (DFOS), in virtue of their low size, light weight, high sensitivity and the ability to detect small strain changes, which makes them particularly effective in monitoring the early stages of damage progression. As part of the TU-LEARN (Structural Life Extension Enhanced by Artificial Intelligence) project, funded by Unione Europea – Next Generation EU, under the PRIN 2022 PNRR – D.D. n. 1409 del 14-09-2022 program, this study investigates the fatigue-driven progression of LVI-induced damage using a Brillouin Optical Frequency-Domain Analysis (BOFDA) system capable of distributed strain measurements with 8-mm spatial resolution. The experimental investigation was conducted on multiple CFRP specimens with nominal dimensions of 100 mm × 150 mm × 2.7 mm. All laminates featured a symmetrical stacking sequence of [(45/−45/90/0)]₂s. For DFOS measurements, a polyimide-coated optical fiber with an outer diameter of 145 μm was bonded to the surface of each specimen, as highlighted in orange in Fig. 1(a). Additionally, six PZT transducers were surface-mounted in a 2×3 array near the central area of each panel, to realize ultrasonic guided wave (UGW) investigation along multiple directions. Each specimen was impacted at its planar center with an energy level of 15 J using a StepLab DW 2000 drop tower. Then, a compressive-compressive fatigue loading was applied under cyclic conditions (stress ratio R = 0.1, fatigue load frequency f = 4 Hz), using a StepLab Dynamic UD040. In the pristine state, after the impact and at predetermined interruption points of the fatigue load, damage growth was tracked using BOFDA strain maps for 3 different compression loads (L = 5 kN, L = 10 kN, L = 15 kN), as well as UGW-based signal analysis across all actuator-receiver combinations. As an example, we show in Figure 1(b) the strain profiles acquired via our BOFDA sensor, under a constant compressive load of 5 kN and at various fatigue stages. The acquired profiles show a gradual increase in the compressive strain levels, compatible with the delamination growth and consequent stiffness degradation of the laminate. Some acceleration in the strain increase was observed when passing from 800k to 1000k fatigue cycles, i.e. in proximity of the panel failure occurred after 1010k cycles. Similar results, obtained on other panels and with different compressive loads, indicate that the high-resolution strain field measurements provided by BOFDA sensors are effective in indicating internal damage progression in CFRP panels subjected to cyclic loading.
- Open Access
- 17 May 2026
- Published by Wiley in Macromolecular Symposia
- p. e70392
Statistical Variability of Guided Ultrasonic Waves in SHM Systems for Damage Identification in CFRP Components
Structural Health Monitoring (SHM) systems based on Guided Ultrasonic Waves are pivotal for the transition from damage tolerance to condition‐based design in aerospace Composite Fiber Reinforced Polymers (CFRP) components. However, environmental and operational variability poses a critical challenge for baseline‐free methods. This work investigates the statistical variability of Lamb waves to validate a population‐based diagnostic approach. The study involved an experimental campaign on 35 CFRP plates subjected to Low‐Velocity Impacts (15 J) and monitored via a piezoelectric sensor network. Parallelly, a Finite Element (FE) model was developed to augment the database. The results highlight that the high intrinsic dispersion within the pristine population overlaps significantly with the damaged population distribution, preventing simple threshold‐based detection. This finding emphasizes the limitations of purely experimental statistical baselines and suggests the implementation of hybrid numerical‐experimental databases to train robust Machine Learning algorithms.
- 17 May 2026
- Published by Wiley in Macromolecular Symposia
- p. e70392
Open AccessStatistical Variability of Guided Ultrasonic Waves in SHM Systems for Damage Identification in CFRP Components
Structural Health Monitoring (SHM) systems based on Guided Ultrasonic Waves are pivotal for the transition from damage tolerance to condition‐based design in aerospace Composite Fiber Reinforced Polymers (CFRP) components. However, environmental and operational variability poses a critical challenge for baseline‐free methods. This work investigates the statistical variability of Lamb waves to validate a population‐based diagnostic approach. The study involved an experimental campaign on 35 CFRP plates subjected to Low‐Velocity Impacts (15 J) and monitored via a piezoelectric sensor network. Parallelly, a Finite Element (FE) model was developed to augment the database. The results highlight that the high intrinsic dispersion within the pristine population overlaps significantly with the damaged population distribution, preventing simple threshold‐based detection. This finding emphasizes the limitations of purely experimental statistical baselines and suggests the implementation of hybrid numerical‐experimental databases to train robust Machine Learning algorithms.