Nikita Rashutin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nikita Rashutin has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Alexander Ilyin
Frumkin Institute of Physical Chemistry and Electrochemistry Russian Academy of Sciences, 31-4, Leninsky Prospect, Moscow 119071, Russia
1 shared publication Gennadiy Yudin
1 shared publication- Ivan Tugolukov1 shared publication
- Mihail Kryukov1 shared publication
- Nikita Burenkov1 shared publication
- Peter Olegovich Rusinov
Department of Materials Engineering, Advanced School of Engineering, MIREA-Russian Technological University, 119454 Moscow, Russia
1 shared publication
Latest Publications
- 30 July 2026
- Published by Moscow Power Engineering Institute (MPEI) in Elektrichestvo
- No. 7,p. 81-88
The Use of Carbon Nanotubes to Produce Highly Efficient Electrically Conducting Composite Materials for Additive Manufacturing
The article deals with studying the possibility of making electrically conducting polymer composite materials (PCMs) for use in LCD printing with applying commercial photopolymer resins and standard 3D printers. The key challenges encountered in dispersing carbon nanotubes (CNTs) in photopolymer matrices stemming from strong van der Waals interactions and the tendency of nanotubes to aggregate are discussed. Various technological methods for producing conducting compositions are analyzed, including mechanical (high speed homogenization and ultrasonic treatment) and chemical dispersion, the use of surfactants and solvents, as well as the application of binary fillers. The electrophysical properties of the resulting materials were evaluated according to GOST and ASTM standards. It is shown that the introduction of single-walled carbon nanotubes together with carbon black allows achieving a volume resistivity of 0.6–1.5 Ω‧m, whereas when taken separately, these fillers do not provide resistivity below 107 Ω‧m within the studied concentration range. It has been established that the filler distribution uniformity and the suspension stability are the key influencing factors. The results obtained demonstrate the possibility in principle to perform additive manufacturing of conducting products using standard equipment. The obtained data can be used in the development of composites for flexible electronics, sensors, and electromagnetic shielding systems. Статья посвящена созданию токопроводящих полимерных композиционных материалов для использования при LCD-печати с применением коммерческих фотополимерных смол и стандартных 3D-принтеров. Рассмотрены ключевые проблемы диспергирования углеродных нанотрубок в фотополимерных матрицах, обусловленные сильными Ван-дер-Ваальсовыми взаимодействиями и склонностью нанотрубок к агрегации. Проанализированы различные технологические приёмы получения проводящих композиций, включая механическое (высокоскоростное гомогенизирование, ультразвуковая обработка) и химическое диспергирование, применение поверхностно-активных веществ, растворителей, а также использование бинарных наполнителей. Проведена оценка электрофизических свойств полученных материалов по методикам ГОСТ и ASTM. Показано, что введение одностенных углеродных нанотрубок совместно с техническим углеродом позволяет достичь удельного объёмного электрического сопротивления 0,6–1,5 Ом‧м, тогда как по отдельности эти наполнители в исследуемом диапазоне концентраций не обеспечивают сопротивления менее 10⁷ Ом‧м. Установлено, что ключевыми факторами являются равномерность распределения наполнителя и стабильность суспензии. Результаты работы демонстрируют принципиальную возможность аддитивного производства токопроводящих изделий на стандартном оборудовании. Полученные данные могут быть использованы при разработке композитов для гибкой электроники, датчиков и систем электромагнитного экранирования.
- 30 July 2026
- Published by Moscow Power Engineering Institute (MPEI) in Elektrichestvo
- No. 7,p. 81-88
The Use of Carbon Nanotubes to Produce Highly Efficient Electrically Conducting Composite Materials for Additive Manufacturing
The article deals with studying the possibility of making electrically conducting polymer composite materials (PCMs) for use in LCD printing with applying commercial photopolymer resins and standard 3D printers. The key challenges encountered in dispersing carbon nanotubes (CNTs) in photopolymer matrices stemming from strong van der Waals interactions and the tendency of nanotubes to aggregate are discussed. Various technological methods for producing conducting compositions are analyzed, including mechanical (high speed homogenization and ultrasonic treatment) and chemical dispersion, the use of surfactants and solvents, as well as the application of binary fillers. The electrophysical properties of the resulting materials were evaluated according to GOST and ASTM standards. It is shown that the introduction of single-walled carbon nanotubes together with carbon black allows achieving a volume resistivity of 0.6–1.5 Ω‧m, whereas when taken separately, these fillers do not provide resistivity below 107 Ω‧m within the studied concentration range. It has been established that the filler distribution uniformity and the suspension stability are the key influencing factors. The results obtained demonstrate the possibility in principle to perform additive manufacturing of conducting products using standard equipment. The obtained data can be used in the development of composites for flexible electronics, sensors, and electromagnetic shielding systems. Статья посвящена созданию токопроводящих полимерных композиционных материалов для использования при LCD-печати с применением коммерческих фотополимерных смол и стандартных 3D-принтеров. Рассмотрены ключевые проблемы диспергирования углеродных нанотрубок в фотополимерных матрицах, обусловленные сильными Ван-дер-Ваальсовыми взаимодействиями и склонностью нанотрубок к агрегации. Проанализированы различные технологические приёмы получения проводящих композиций, включая механическое (высокоскоростное гомогенизирование, ультразвуковая обработка) и химическое диспергирование, применение поверхностно-активных веществ, растворителей, а также использование бинарных наполнителей. Проведена оценка электрофизических свойств полученных материалов по методикам ГОСТ и ASTM. Показано, что введение одностенных углеродных нанотрубок совместно с техническим углеродом позволяет достичь удельного объёмного электрического сопротивления 0,6–1,5 Ом‧м, тогда как по отдельности эти наполнители в исследуемом диапазоне концентраций не обеспечивают сопротивления менее 10⁷ Ом‧м. Установлено, что ключевыми факторами являются равномерность распределения наполнителя и стабильность суспензии. Результаты работы демонстрируют принципиальную возможность аддитивного производства токопроводящих изделий на стандартном оборудовании. Полученные данные могут быть использованы при разработке композитов для гибкой электроники, датчиков и систем электромагнитного экранирования.
- Open Access
Development and Research of Anti-Corrosion Polymer Coatings with Microdefect Blocking Effect
Corrosion of materials is a global issue affecting various industries. It leads to a gradual decline in the durability and reliability of materials, resulting in significant economic losses and posing serious risks to human health. To address the challenge of enhancing reliability and durability when materials are exposed to aggressive environments, this study developed new polymer protective coatings. These coatings involve reinforcing an epoxy resin-based polymer matrix with zinc and microencapsulated corrosion inhibitors (activated Al2O3 + HEDP; activated Al2O3 + PPA; activated Al2O3 + ATMP). These microscopic containers encapsulate the corrosion inhibitors. The microstructure of the microcapsules was examined using scanning electron microscopy (SEM) and optical microscopy. Accelerated corrosion tests were performed on the reinforced modified coatings. Coatings reinforced with activated Al2O3 + HEDP microcapsules demonstrated excellent corrosion resistance in a 3% NaCl solution. In contrast, samples coated with unmodified zinc-filled coatings and coatings modified with Al2O3 + PPA exhibited the lowest resistance in a 3% NaCl solution. The study also investigated the microdefect-blocking effect in reinforced coatings, which is achieved by filling the pores of the polymer coating with products formed from inhibitor–metal interactions.
Open AccessDevelopment and Research of Anti-Corrosion Polymer Coatings with Microdefect Blocking Effect
Corrosion of materials is a global issue affecting various industries. It leads to a gradual decline in the durability and reliability of materials, resulting in significant economic losses and posing serious risks to human health. To address the challenge of enhancing reliability and durability when materials are exposed to aggressive environments, this study developed new polymer protective coatings. These coatings involve reinforcing an epoxy resin-based polymer matrix with zinc and microencapsulated corrosion inhibitors (activated Al2O3 + HEDP; activated Al2O3 + PPA; activated Al2O3 + ATMP). These microscopic containers encapsulate the corrosion inhibitors. The microstructure of the microcapsules was examined using scanning electron microscopy (SEM) and optical microscopy. Accelerated corrosion tests were performed on the reinforced modified coatings. Coatings reinforced with activated Al2O3 + HEDP microcapsules demonstrated excellent corrosion resistance in a 3% NaCl solution. In contrast, samples coated with unmodified zinc-filled coatings and coatings modified with Al2O3 + PPA exhibited the lowest resistance in a 3% NaCl solution. The study also investigated the microdefect-blocking effect in reinforced coatings, which is achieved by filling the pores of the polymer coating with products formed from inhibitor–metal interactions.