Yunlong Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yunlong Zhang has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Ben Ma
AVIC Touchstone Testing Innovation (Wuxi) Co., Ltd., Wuxi 214101, China
1 shared publication - Chenghai Li
College of Materials Science and Engineering, Jiamusi University, Jiamusi 154007, China
1 shared publication - Hehe Chen
AECC Beijing Institute of Aeronautical Materials, Beijing 100095, China
1 shared publication - Hisham Al-Ward
Department of Biochemistry and Molecular Biology, Jiamusi University School of Basic Medical Sciences, Jiamusi, China
1 shared publication - Hongbin Qiu
Jiamusi University
1 shared publication - Jianwei Hu
AVIC Touchstone Testing Innovation (Wuxi) Co., Ltd., Wuxi 214101, China
1 shared publication
Latest Publications
- Open Access
Study on the Wear and Corrosion Resistance of PEO/SAM/MWCNTs Composite Coating on TC4/Mg Interpenetrating Composite
To address the severe wear and galvanic corrosion of TC4/Mg three-dimensional interpenetrating composites caused by the potential difference and hardness disparity between the two phases, this work proposes a hybrid surface modification strategy combining plasma electrolytic oxidation (PEO) with a self-assembled monolayer (SAM) doped with multi-walled carbon nanotubes (MWCNTs). A PEO ceramic coating was first grown in situ on the composite surface, followed by sealing modification using MWCNTs-containing SAM. The microstructure, phase composition, tribological behavior and potentiodynamic polarization curves of the coatings were systematically evaluated. The results show that the PEO coating is mainly composed of Mg2SiO4, MgO, MgF2 and TiO2, exhibiting a typical porous structure. After the MWCNTs-doped SAM composite modification, the nano-fillers and the molecular layer synergistically seal the micropores and cracks, and the surface transforms into a continuous and dense layered morphology. Wear tests reveal that the composite coating reduces the friction coefficient to 0.195 and decreases the wear volume by 93.53% compared with the bare composite. The “micro-roller bearing” effect and debris adsorption of MWCNTs significantly improve the wear resistance, and the dominant wear mechanism changes from abrasive wear to three-body wear. Electrochemical measurements show that the corrosion current density of the composite coating decreases from 2 × 10−4 A·cm−2 (bare composite) to 1.401 × 10−9 A·cm−2, i.e., a reduction by five orders of magnitude, with a protection efficiency of 99.99%. This is attributed to the physical barrier effect of the PEO coating and the synergistic sealing of defects, as well as the blocking of electron transfer by MWCNTs/SAM. The multi-level protection system of “PEO + MWCNTs + SAM” constructed in this work achieves a synergistic improvement in both wear resistance and corrosion resistance of the TC4/Mg two-phase interpenetrating composite, and holds promise for further investigation as an osseointegration implant material.
Open AccessStudy on the Wear and Corrosion Resistance of PEO/SAM/MWCNTs Composite Coating on TC4/Mg Interpenetrating Composite
To address the severe wear and galvanic corrosion of TC4/Mg three-dimensional interpenetrating composites caused by the potential difference and hardness disparity between the two phases, this work proposes a hybrid surface modification strategy combining plasma electrolytic oxidation (PEO) with a self-assembled monolayer (SAM) doped with multi-walled carbon nanotubes (MWCNTs). A PEO ceramic coating was first grown in situ on the composite surface, followed by sealing modification using MWCNTs-containing SAM. The microstructure, phase composition, tribological behavior and potentiodynamic polarization curves of the coatings were systematically evaluated. The results show that the PEO coating is mainly composed of Mg2SiO4, MgO, MgF2 and TiO2, exhibiting a typical porous structure. After the MWCNTs-doped SAM composite modification, the nano-fillers and the molecular layer synergistically seal the micropores and cracks, and the surface transforms into a continuous and dense layered morphology. Wear tests reveal that the composite coating reduces the friction coefficient to 0.195 and decreases the wear volume by 93.53% compared with the bare composite. The “micro-roller bearing” effect and debris adsorption of MWCNTs significantly improve the wear resistance, and the dominant wear mechanism changes from abrasive wear to three-body wear. Electrochemical measurements show that the corrosion current density of the composite coating decreases from 2 × 10−4 A·cm−2 (bare composite) to 1.401 × 10−9 A·cm−2, i.e., a reduction by five orders of magnitude, with a protection efficiency of 99.99%. This is attributed to the physical barrier effect of the PEO coating and the synergistic sealing of defects, as well as the blocking of electron transfer by MWCNTs/SAM. The multi-level protection system of “PEO + MWCNTs + SAM” constructed in this work achieves a synergistic improvement in both wear resistance and corrosion resistance of the TC4/Mg two-phase interpenetrating composite, and holds promise for further investigation as an osseointegration implant material.
- Open Access
- 7 February 2022
- Published by Springer Nature in Research Square
Influence of monocalcium phosphate on the properties of bioactive magnesium phosphate bone cement
Background: The bone defects caused by different reasons led to deformity and dysfunction of human body. Considering the need for clinical application, it was essential for bone regeneration to exploit a scaffold with bioactive bone cement. In this paper, we fabricated bioactive magnesium phosphate bone cement (BMPC) at room temperature, then it was set at 37℃ and 100% humidity for 2h. Methods: The process was as follows. MgO was formed by calcining Mg2(OH)2CO3, MgO, KH2PO4 and carboxymethyl chitosan were mixed to form magnesium phosphate bone cement(MPC), then Ca(H2PO4)2 was added to neutralize alkaline product after MPC hydration to fabricate bioactive magnesium phosphate bone cement (BMPC). The influence of doped content of Ca(H2PO4)2 on the properties of bone cement was discussed. Results: The results showed that Ca(H2PO4)2 and carboxymethyl chitosan can adjust the setting time of bone cement within the scope of 8 minute and 25 minute. The compressive strength increased first and then decreased. After 48h without additional pressure, the compressive strength reached the maximum value, so it was about of 38.6 MPa. Ca(H2PO4)2 and carboxymethyl chitosan can play a synergistic role in regulating the BMPC properties. BMPC was degradable in the simulated body fluid (SBF). The results of cytotoxicity experiment and laser confocal microscopy experiment indicated that BMPC fabricated at room temperature had better biocompatibility and degradability, which was more consistent with clinical operation requirement.Conclusions: BMPC can be used as a promising orthopedic material, and it can meet with the needs for repairing bone defects.
- 7 February 2022
- Published by Springer Nature in Research Square
Open AccessInfluence of monocalcium phosphate on the properties of bioactive magnesium phosphate bone cement
Background: The bone defects caused by different reasons led to deformity and dysfunction of human body. Considering the need for clinical application, it was essential for bone regeneration to exploit a scaffold with bioactive bone cement. In this paper, we fabricated bioactive magnesium phosphate bone cement (BMPC) at room temperature, then it was set at 37℃ and 100% humidity for 2h. Methods: The process was as follows. MgO was formed by calcining Mg2(OH)2CO3, MgO, KH2PO4 and carboxymethyl chitosan were mixed to form magnesium phosphate bone cement(MPC), then Ca(H2PO4)2 was added to neutralize alkaline product after MPC hydration to fabricate bioactive magnesium phosphate bone cement (BMPC). The influence of doped content of Ca(H2PO4)2 on the properties of bone cement was discussed. Results: The results showed that Ca(H2PO4)2 and carboxymethyl chitosan can adjust the setting time of bone cement within the scope of 8 minute and 25 minute. The compressive strength increased first and then decreased. After 48h without additional pressure, the compressive strength reached the maximum value, so it was about of 38.6 MPa. Ca(H2PO4)2 and carboxymethyl chitosan can play a synergistic role in regulating the BMPC properties. BMPC was degradable in the simulated body fluid (SBF). The results of cytotoxicity experiment and laser confocal microscopy experiment indicated that BMPC fabricated at room temperature had better biocompatibility and degradability, which was more consistent with clinical operation requirement.Conclusions: BMPC can be used as a promising orthopedic material, and it can meet with the needs for repairing bone defects.