Sinem Uluocak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sinem Uluocak has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Alfredo Peña
DTU Wind and Energy Systems, Technical University of Denmark, 4000 Roskilde, Denmark
4 shared publications - Andreas Rott
Carl von Ossietzky Universität Oldenburg, School of Mathematics and Science, Institute of Physics
3 shared publications - Martin Kühn
Carl von Ossietzky Universität Oldenburg, School of Mathematics and Science, Institute of Physics
3 shared publications Andreas Rott
Carl von Ossietzky Universität Oldenburg
1 shared publicationMartin Kühn
Carl von Ossietzky Universität Oldenburg
1 shared publicationNikolas Angelou
Technical University of Denmark
1 shared publication
Latest Publications
- Open Access
- 6 November 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-31
Comment on egusphere-2026-825
Wind lidars are increasingly used for wind turbine power estimation, load analysis, and control purposes, but their ability to accurately capture turbulence is limited by the large probe volumes of lidars, which attenuate measured turbulence through spatial averaging. We investigate the effects of probe volume averaging on lidar turbulence characteristics as a function of the probe volume over integral length scale ratios using a wind tunnel study. This is facilitated by generating tailor-made turbulent flow conditions using an active grid and by adjusting the focus distance of a short-range continuous-wave (CW) lidar. A hot-wire anemometer is used as reference sensor. First, a spectrum model for the lidar averaging effect is implemented by applying a Lorentzian filter to Mann-model spectra derived from hot-wire measurements, accurately capturing velocity spectrum attenuation with increasing probe volume averaging. Second, the ability of the lidar to estimate turbulence statistics including the integral length scale and velocity variance is evaluated by comparing lidar to hot-wire ratios across all cases. Results show that conventional lidar-derived length scales are overestimated while velocity variances are underestimated with increasing probe volume averaging. Both the modelled and conventionally derived lidar velocity variance are attenuated from 10 % to 80 % with increasing probe volume averaging. In contrast, the spectrum-based lidar variance, derived directly from the averaged lidar Doppler spectrum compensates for probe volume averaging, yielding variance estimates that are significantly less affected by this ratio with an average relative error of +20 % compared to the hot-wire data. The correction for velocity gradients in the wind tunnel flow reduces the average relative error of spectrum-based lidar velocity variances to +10 %.
- 6 November 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-31
Open AccessComment on egusphere-2026-825
Wind lidars are increasingly used for wind turbine power estimation, load analysis, and control purposes, but their ability to accurately capture turbulence is limited by the large probe volumes of lidars, which attenuate measured turbulence through spatial averaging. We investigate the effects of probe volume averaging on lidar turbulence characteristics as a function of the probe volume over integral length scale ratios using a wind tunnel study. This is facilitated by generating tailor-made turbulent flow conditions using an active grid and by adjusting the focus distance of a short-range continuous-wave (CW) lidar. A hot-wire anemometer is used as reference sensor. First, a spectrum model for the lidar averaging effect is implemented by applying a Lorentzian filter to Mann-model spectra derived from hot-wire measurements, accurately capturing velocity spectrum attenuation with increasing probe volume averaging. Second, the ability of the lidar to estimate turbulence statistics including the integral length scale and velocity variance is evaluated by comparing lidar to hot-wire ratios across all cases. Results show that conventional lidar-derived length scales are overestimated while velocity variances are underestimated with increasing probe volume averaging. Both the modelled and conventionally derived lidar velocity variance are attenuated from 10 % to 80 % with increasing probe volume averaging. In contrast, the spectrum-based lidar variance, derived directly from the averaged lidar Doppler spectrum compensates for probe volume averaging, yielding variance estimates that are significantly less affected by this ratio with an average relative error of +20 % compared to the hot-wire data. The correction for velocity gradients in the wind tunnel flow reduces the average relative error of spectrum-based lidar velocity variances to +10 %.
- Open Access
- 23 June 2026
- Published by Copernicus GmbH
- p. 1-31
Comment on egusphere-2026-825
Wind lidars are increasingly used for wind turbine power estimation, load analysis, and control purposes, but their ability to accurately capture turbulence is limited by the large probe volumes of lidars, which attenuate measured turbulence through spatial averaging. We investigate the effects of probe volume averaging on lidar turbulence characteristics as a function of the probe volume over integral length scale ratios using a wind tunnel study. This is facilitated by generating tailor-made turbulent flow conditions using an active grid and by adjusting the focus distance of a short-range continuous-wave (CW) lidar. A hot-wire anemometer is used as reference sensor. First, a spectrum model for the lidar averaging effect is implemented by applying a Lorentzian filter to Mann-model spectra derived from hot-wire measurements, accurately capturing velocity spectrum attenuation with increasing probe volume averaging. Second, the ability of the lidar to estimate turbulence statistics including the integral length scale and velocity variance is evaluated by comparing lidar to hot-wire ratios across all cases. Results show that conventional lidar-derived length scales are overestimated while velocity variances are underestimated with increasing probe volume averaging. Both the modelled and conventionally derived lidar velocity variance are attenuated from 10 % to 80 % with increasing probe volume averaging. In contrast, the spectrum-based lidar variance, derived directly from the averaged lidar Doppler spectrum compensates for probe volume averaging, yielding variance estimates that are significantly less affected by this ratio with an average relative error of +20 % compared to the hot-wire data. The correction for velocity gradients in the wind tunnel flow reduces the average relative error of spectrum-based lidar velocity variances to +10 %.
- 23 June 2026
- Published by Copernicus GmbH
- p. 1-31
Open AccessComment on egusphere-2026-825
Wind lidars are increasingly used for wind turbine power estimation, load analysis, and control purposes, but their ability to accurately capture turbulence is limited by the large probe volumes of lidars, which attenuate measured turbulence through spatial averaging. We investigate the effects of probe volume averaging on lidar turbulence characteristics as a function of the probe volume over integral length scale ratios using a wind tunnel study. This is facilitated by generating tailor-made turbulent flow conditions using an active grid and by adjusting the focus distance of a short-range continuous-wave (CW) lidar. A hot-wire anemometer is used as reference sensor. First, a spectrum model for the lidar averaging effect is implemented by applying a Lorentzian filter to Mann-model spectra derived from hot-wire measurements, accurately capturing velocity spectrum attenuation with increasing probe volume averaging. Second, the ability of the lidar to estimate turbulence statistics including the integral length scale and velocity variance is evaluated by comparing lidar to hot-wire ratios across all cases. Results show that conventional lidar-derived length scales are overestimated while velocity variances are underestimated with increasing probe volume averaging. Both the modelled and conventionally derived lidar velocity variance are attenuated from 10 % to 80 % with increasing probe volume averaging. In contrast, the spectrum-based lidar variance, derived directly from the averaged lidar Doppler spectrum compensates for probe volume averaging, yielding variance estimates that are significantly less affected by this ratio with an average relative error of +20 % compared to the hot-wire data. The correction for velocity gradients in the wind tunnel flow reduces the average relative error of spectrum-based lidar velocity variances to +10 %.
- Open Access
- 1 June 2026
- Published by Copernicus GmbH in EGUsphere
- Vol. 2026, 1-31
Lidar probe volume averaging effect on the along-wind turbulence statistics
Wind lidars are increasingly used for wind turbine power estimation, load analysis, and control purposes, but their ability to accurately capture turbulence is limited by the large probe volumes of lidars, which attenuate measured turbulence through spatial averaging. We investigate the effects of probe volume averaging on lidar turbulence characteristics as a function of the probe volume over integral length scale ratios using a wind tunnel study. This is facilitated by generating tailor-made turbulent flow conditions using an active grid and by adjusting the focus distance of a short-range continuous-wave (CW) lidar. A hot-wire anemometer is used as reference sensor. First, a spectrum model for the lidar averaging effect is implemented by applying a Lorentzian filter to Mann-model spectra derived from hot-wire measurements, accurately capturing velocity spectrum attenuation with increasing probe volume averaging. Second, the ability of the lidar to estimate turbulence statistics including the integral length scale and velocity variance is evaluated by comparing lidar to hot-wire ratios across all cases. Results show that conventional lidar-derived length scales are overestimated while velocity variances are underestimated with increasing probe volume averaging. Both the modelled and conventionally derived lidar velocity variance are attenuated from 10 % to 80 % with increasing probe volume averaging. In contrast, the spectrum-based lidar variance, derived directly from the averaged lidar Doppler spectrum compensates for probe volume averaging, yielding variance estimates that are significantly less affected by this ratio with an average relative error of +20 % compared to the hot-wire data. The correction for velocity gradients in the wind tunnel flow reduces the average relative error of spectrum-based lidar velocity variances to +10 %.
- 1 June 2026
- Published by Copernicus GmbH in EGUsphere
- Vol. 2026, 1-31
Open AccessLidar probe volume averaging effect on the along-wind turbulence statistics
Wind lidars are increasingly used for wind turbine power estimation, load analysis, and control purposes, but their ability to accurately capture turbulence is limited by the large probe volumes of lidars, which attenuate measured turbulence through spatial averaging. We investigate the effects of probe volume averaging on lidar turbulence characteristics as a function of the probe volume over integral length scale ratios using a wind tunnel study. This is facilitated by generating tailor-made turbulent flow conditions using an active grid and by adjusting the focus distance of a short-range continuous-wave (CW) lidar. A hot-wire anemometer is used as reference sensor. First, a spectrum model for the lidar averaging effect is implemented by applying a Lorentzian filter to Mann-model spectra derived from hot-wire measurements, accurately capturing velocity spectrum attenuation with increasing probe volume averaging. Second, the ability of the lidar to estimate turbulence statistics including the integral length scale and velocity variance is evaluated by comparing lidar to hot-wire ratios across all cases. Results show that conventional lidar-derived length scales are overestimated while velocity variances are underestimated with increasing probe volume averaging. Both the modelled and conventionally derived lidar velocity variance are attenuated from 10 % to 80 % with increasing probe volume averaging. In contrast, the spectrum-based lidar variance, derived directly from the averaged lidar Doppler spectrum compensates for probe volume averaging, yielding variance estimates that are significantly less affected by this ratio with an average relative error of +20 % compared to the hot-wire data. The correction for velocity gradients in the wind tunnel flow reduces the average relative error of spectrum-based lidar velocity variances to +10 %.
- Open Access
- 1 May 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3224 (3)
Estimation of near wake turbulence characteristics with dual WindScanner lidar measurements
Wind turbine wake characterization has become increasingly important with the growth of wind farms and the need for accurate load assessment, power prediction, and advanced control strategies. Spatially distributed measurements are essential to better understand complex wake flow fields. Wind lidars are particularly useful for this purpose due to their ability to remotely scan large areas. This study presents the methodology for estimation of near wake velocity and turbulence statistics using a dual WindScanner lidar setup and a met-mast array comprising thirty 3D sonic anemometers as reference. Measurements are performed on a vertical measurement plane at 0.8 D downstream of a utility-scale wind turbine ( D = 115 m). The results show a clear velocity deficit in the wake region and increased turbulence levels along the wake edges. Good agreement is found between lidar and sonic radial velocities. However, lidar-derived radial velocity variances along two beams are 22 % and 28 % lower than the sonic equivalents due to probe-volume averaging. To correct this filtering effect, we estimate unfiltered radial velocity variances from the averaged Doppler radial velocity spectrum of the lidar. This method reduces the radial velocity variance error to 8 % and 6 %, demonstrating the potential of lidar for turbulence measurements within wakes.
- 1 May 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3224 (3)
Open AccessEstimation of near wake turbulence characteristics with dual WindScanner lidar measurements
Wind turbine wake characterization has become increasingly important with the growth of wind farms and the need for accurate load assessment, power prediction, and advanced control strategies. Spatially distributed measurements are essential to better understand complex wake flow fields. Wind lidars are particularly useful for this purpose due to their ability to remotely scan large areas. This study presents the methodology for estimation of near wake velocity and turbulence statistics using a dual WindScanner lidar setup and a met-mast array comprising thirty 3D sonic anemometers as reference. Measurements are performed on a vertical measurement plane at 0.8 D downstream of a utility-scale wind turbine ( D = 115 m). The results show a clear velocity deficit in the wake region and increased turbulence levels along the wake edges. Good agreement is found between lidar and sonic radial velocities. However, lidar-derived radial velocity variances along two beams are 22 % and 28 % lower than the sonic equivalents due to probe-volume averaging. To correct this filtering effect, we estimate unfiltered radial velocity variances from the averaged Doppler radial velocity spectrum of the lidar. This method reduces the radial velocity variance error to 8 % and 6 %, demonstrating the potential of lidar for turbulence measurements within wakes.