Eric Tomasella
Eric Tomasella has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Angélique Bousquet
Institut de Chimie de Clermont-Ferrand (ICCF) Université Clermont Auvergne CNRS Clermont Auvergne INP F-63000 CLERMONT-FERRAND
2 shared publications - Mireille Richard-Plouet
Nantes Université, CNRS, Institut des Matériaux de Nantes Jean Rouxel, IMN, F-44000 Nantes, France
2 shared publications - Thierry Sauvage
CNRS-CEMHTI, Orléans University, 3A, Rue de la Ferollerie, 45071 Orleans, Cedex 2, France
2 shared publications - Aissatou Diop
GREMI (Groupe de Recherches sur l'Énergétique des Milieux Ionisés) UMR7344 CNRS/Université d'Orléans Orléans France
1 shared publication Amir Kabouia
1 shared publicationAntoine Goullet
1 shared publication
Latest Publications
- Open Access
- 4 August 2026
- Published by Elsevier in SSRN Electronic Journal
Photocatalytic Properties of Bismuth Oxyfluoride Thin Films Deposited by Reactive Magnetron Sputtering in Ar/O2/CF4 Atmosphere
Bismuth oxyfluoride films were successfully deposited by reactive magnetron sputtering using different Ar/O2/CF4 gas mixtures. For a reactive gas ratio (Rf), defined as the O2/(O2 + CF4) flow rate ratio, ranging from 0 to 0.6, the films consist of two phase-system composed of BiO0.5F2 and metallic bismuth (Bi0); whereas for Rf = 0, a single phase BiF3 is observed when Rf > 0.5. The amount of metallic Bismuth within the oxyfluoride matrix can be tuned not only by Rf, but also by adjusting the target power or by varying a single reactive gas flow rate. Increasing the film thickness does not significantly affect the composition but enhances crystallization of the phases. Hence, we succeed in forming one-step Bi/BiO0.5F2 heterojunctions, where the metal presence improves the light absorption, the photogenerated carrier separation, and thus the photocatalytic efficiency for Methylene Orange, MO, degradation in water. Among all the conditions investigated, the film obtained with Rf = 0.3 and a deposition time, td = 20 min exhibits the best overall performance. Indeed, 90 % of MO is degraded after 2 hours of irradiation, and the catalyst remains stable over 3 photocatalytic cycles (approximately 9 hours of total use). Moreover, this material selectively photoconverts CO2 in CO, with a higher efficiency to create useful electrons (rē ≈ 29 mmol/molcata) than pure BiO0.5F2 thin film, and even nanostructured TiO2 P25 (rē ≈ 11 mmol/molcata).
- 4 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessPhotocatalytic Properties of Bismuth Oxyfluoride Thin Films Deposited by Reactive Magnetron Sputtering in Ar/O2/CF4 Atmosphere
Bismuth oxyfluoride films were successfully deposited by reactive magnetron sputtering using different Ar/O2/CF4 gas mixtures. For a reactive gas ratio (Rf), defined as the O2/(O2 + CF4) flow rate ratio, ranging from 0 to 0.6, the films consist of two phase-system composed of BiO0.5F2 and metallic bismuth (Bi0); whereas for Rf = 0, a single phase BiF3 is observed when Rf > 0.5. The amount of metallic Bismuth within the oxyfluoride matrix can be tuned not only by Rf, but also by adjusting the target power or by varying a single reactive gas flow rate. Increasing the film thickness does not significantly affect the composition but enhances crystallization of the phases. Hence, we succeed in forming one-step Bi/BiO0.5F2 heterojunctions, where the metal presence improves the light absorption, the photogenerated carrier separation, and thus the photocatalytic efficiency for Methylene Orange, MO, degradation in water. Among all the conditions investigated, the film obtained with Rf = 0.3 and a deposition time, td = 20 min exhibits the best overall performance. Indeed, 90 % of MO is degraded after 2 hours of irradiation, and the catalyst remains stable over 3 photocatalytic cycles (approximately 9 hours of total use). Moreover, this material selectively photoconverts CO2 in CO, with a higher efficiency to create useful electrons (rē ≈ 29 mmol/molcata) than pure BiO0.5F2 thin film, and even nanostructured TiO2 P25 (rē ≈ 11 mmol/molcata).
- Open Access
- 23 May 2026
- Published by Elsevier in SSRN Electronic Journal
Structural, chemical and optical characterizations of W/W-Si-C:H/TaOₓNᵧ multilayer thin films deposited by hybrid plasma processes for concentrated solar technologies
A thin-film multilayer stack was developed using hybrid plasma processes for use as absorber coatings in concentrated solar thermal systems, at operating temperatures around 500 °C in air or vacuum. The stack comprises a tungsten (W) infrared reflector, a spectrally selective absorber layer of hydrogenated tungsten-silicon carbide (W-Si-C:H), and an antireflective tantalum oxynitride (TaOₓNᵧ) layer.First, the structural and chemical properties of the W-Si-C:H layers were characterized using transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). In the second phase, the structural and optical properties of the entire stack were investigated. Ion beam analysis (IBA) was employed to precisely determine the composition of each layer in the coating. The solar absorptance (αₛ), thermal emittance (ε(T)) and heliothermal efficiency (η(T)) were then evaluated from UV-IR spectrophotometry to determine the optimal antireflective layer configuration. Our findings demonstrated that the addition of the antireflective layer increases the heliothermal efficiency from 38.4% to 62.8%.
- 23 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessStructural, chemical and optical characterizations of W/W-Si-C:H/TaOₓNᵧ multilayer thin films deposited by hybrid plasma processes for concentrated solar technologies
A thin-film multilayer stack was developed using hybrid plasma processes for use as absorber coatings in concentrated solar thermal systems, at operating temperatures around 500 °C in air or vacuum. The stack comprises a tungsten (W) infrared reflector, a spectrally selective absorber layer of hydrogenated tungsten-silicon carbide (W-Si-C:H), and an antireflective tantalum oxynitride (TaOₓNᵧ) layer.First, the structural and chemical properties of the W-Si-C:H layers were characterized using transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). In the second phase, the structural and optical properties of the entire stack were investigated. Ion beam analysis (IBA) was employed to precisely determine the composition of each layer in the coating. The solar absorptance (αₛ), thermal emittance (ε(T)) and heliothermal efficiency (η(T)) were then evaluated from UV-IR spectrophotometry to determine the optimal antireflective layer configuration. Our findings demonstrated that the addition of the antireflective layer increases the heliothermal efficiency from 38.4% to 62.8%.