Danial Zafaranchizadeh Moghaddam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Danial Zafaranchizadeh Moghaddam has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Abolfazl Zaraki
University of Hertfordshire, UK
3 shared publications - Olga Tveretina
University of Hertfordshire
2 shared publications - Hamed Rahimi Nohooji
University of Luxembourg, Luxembourg
1 shared publication - Maryam Banitalebi Dehkordi
University of Hertfordshire, UK
1 shared publication
Latest Publications
- Open Access
- 18 August 2026
- Published by MDPI AG in Preprints.org
AEGIS: An Age-Aware, Evidence-Guarded Safe-Action Layer Fusing RGB-D Sensing with Vision–Language Monitoring for Collision-Aware Robotic Manipulation
A safety margin derived from a vision–language verdict is only as valid as that verdict is recent, yet run-time safety filters model state noise, not the staleness of an intermittent label. We present AEGIS, a safe-action projection whose hold radius is an explicit function of a semantic belief and of the age of the verdict that produced it, with a conditional grasp-site separation result and a fresh-evidence feasibility property under stated assumptions. AEGIS runs on one fixed Intel RealSense D435i: localisation through a calibrated homography with a sub-millimetre mean fitting residual, a workspace-gated intruder detector fused with metric depth, and an on-device verdict returned in a fraction of a second. Beneath it a geometric layer checks and, when necessary, modifies commands against a set of geometric constraints, so it wraps any policy without retraining, reducing accumulated constraint cost in simulation without a significant loss of task success. In a buffer-matched comparison, indexing the margin by verdict age is significantly safer than trusting the latest verdict, raising the fraction of episodes free of any commanded approach to a person, and no constant belief reproduces the behaviour. On the physical Niryo NED3 Pro the logged radius expands as a verdict ages and collapses on a fresh one: AEGIS held positive measured clearance, one trust-latest run ended up inside the detected footprint, and the worst-case policy delivered least. Claims are reported against explicitly separated evidence tiers.
- 18 August 2026
- Published by MDPI AG in Preprints.org
Open AccessAEGIS: An Age-Aware, Evidence-Guarded Safe-Action Layer Fusing RGB-D Sensing with Vision–Language Monitoring for Collision-Aware Robotic Manipulation
A safety margin derived from a vision–language verdict is only as valid as that verdict is recent, yet run-time safety filters model state noise, not the staleness of an intermittent label. We present AEGIS, a safe-action projection whose hold radius is an explicit function of a semantic belief and of the age of the verdict that produced it, with a conditional grasp-site separation result and a fresh-evidence feasibility property under stated assumptions. AEGIS runs on one fixed Intel RealSense D435i: localisation through a calibrated homography with a sub-millimetre mean fitting residual, a workspace-gated intruder detector fused with metric depth, and an on-device verdict returned in a fraction of a second. Beneath it a geometric layer checks and, when necessary, modifies commands against a set of geometric constraints, so it wraps any policy without retraining, reducing accumulated constraint cost in simulation without a significant loss of task success. In a buffer-matched comparison, indexing the margin by verdict age is significantly safer than trusting the latest verdict, raising the fraction of episodes free of any commanded approach to a person, and no constant belief reproduces the behaviour. On the physical Niryo NED3 Pro the logged radius expands as a verdict ages and collapses on a fresh one: AEGIS held positive measured clearance, one trust-latest run ended up inside the detected footprint, and the worst-case policy delivered least. Claims are reported against explicitly separated evidence tiers.
- Open Access
Real-Hardware Deployment of a Nussbaum-Function PID Controller on a Current-Controlled Low-Cost Actuator via Hardware-Aware Optuna Tuning
Real-hardware deployment of adaptive manipulator controllers remains difficult because assumptions made in paper-level formulations are weakened by friction, encoder quantisation, current limits, communication latency, and low-speed actuation nonlinearities. This paper investigates that deployment gap for a recent Nussbaum-function PID controller by translating it from a simulation-level formulation into direct current-command control on a Niryo NED3 Pro actuator. To isolate deployment-layer behaviour from the whole-arm Coriolis, centrifugal, and gravity dynamics, the study is centred on a single decoupled actuator (Dynamixel ID 6, distal wrist) under long-horizon sinusoidal tracking around a fixed operating region. A direct transfer of the baseline law is first reproduced and shown to degrade through cumulative adaptation-state growth, weakening of the Nussbaum modulation, and high internal command saturation. A hardware-oriented implementation is then evaluated that preserves the Nussbaum core while adding adaptation-state regularisation, low-speed velocity-reference feedforward, and tail-region damping; its parameters are selected through a hardware-aware Optuna archive of 79 real-hardware trials with hard rejection of unsafe runs and a score that jointly reflects tracking quality, internal command saturation, actuation activity, and bounded adaptation growth. Over 300 s of continuous operation, the enhanced implementation reduces the mean absolute error from to and the internal command saturation ratio from to relative to the direct baseline, within the reported actuator, trajectory, and safety envelope. The main contribution is therefore not only a tuned controller but a reproducible real-hardware methodology showing how Nussbaum-based PID control can be deployed and improved on a low-cost manipulator when adaptation management, actuation mapping, and hardware-aware optimisation are treated as core elements of the research design.Open AccessReal-Hardware Deployment of a Nussbaum-Function PID Controller on a Current-Controlled Low-Cost Actuator via Hardware-Aware Optuna Tuning
Real-hardware deployment of adaptive manipulator controllers remains difficult because assumptions made in paper-level formulations are weakened by friction, encoder quantisation, current limits, communication latency, and low-speed actuation nonlinearities. This paper investigates that deployment gap for a recent Nussbaum-function PID controller by translating it from a simulation-level formulation into direct current-command control on a Niryo NED3 Pro actuator. To isolate deployment-layer behaviour from the whole-arm Coriolis, centrifugal, and gravity dynamics, the study is centred on a single decoupled actuator (Dynamixel ID 6, distal wrist) under long-horizon sinusoidal tracking around a fixed operating region. A direct transfer of the baseline law is first reproduced and shown to degrade through cumulative adaptation-state growth, weakening of the Nussbaum modulation, and high internal command saturation. A hardware-oriented implementation is then evaluated that preserves the Nussbaum core while adding adaptation-state regularisation, low-speed velocity-reference feedforward, and tail-region damping; its parameters are selected through a hardware-aware Optuna archive of 79 real-hardware trials with hard rejection of unsafe runs and a score that jointly reflects tracking quality, internal command saturation, actuation activity, and bounded adaptation growth. Over 300 s of continuous operation, the enhanced implementation reduces the mean absolute error from to and the internal command saturation ratio from to relative to the direct baseline, within the reported actuator, trajectory, and safety envelope. The main contribution is therefore not only a tuned controller but a reproducible real-hardware methodology showing how Nussbaum-based PID control can be deployed and improved on a low-cost manipulator when adaptation management, actuation mapping, and hardware-aware optimisation are treated as core elements of the research design. - Open Access
- 4 June 2026
- Published by MDPI AG in Preprints.org
Real-Hardware Deployment of a Nussbaum-Function PID Controller on a Current-Controlled Low-Cost Actuator via Hardware-Aware Optuna Tuning
Real-hardware deployment of adaptive manipulator controllers remained difficult because assumptions made in paper-level formulations were often weakened by friction, encoder quantization, current limits, communication latency, and low-speed actuation nonlinearities. This paper investigated that deployment gap for a recent Nussbaum-function PID controller by translating it from a simulation-level formulation into direct current-command control on a Niryo NED3 Pro actuator. To isolate deployment-layer behaviour from whole-arm Coriolis, centrifugal, and gravity dynamics, the study focused on a single decoupled actuator (Dynamixel ID 6, distal wrist) under long-horizon sinusoidal tracking around a fixed operating region.A direct transfer of the baseline control law was first reproduced and was shown to degrade due to cumulative adaptation-state growth, weakening of the Nussbaum modulation, and high internal command saturation. A hardware-oriented implementation was then evaluated that preserved the Nussbaum core while introducing adaptation-state regularization, low-speed velocity-reference feedforward, and tail-region damping. Its parameters were selected through a hardware-aware Optuna optimization archive comprising 79 real-hardware trials, with unsafe runs rejected and a composite score reflecting tracking quality, internal command saturation, actuation activity, and bounded adaptation growth.Over 300 s of continuous operation, the enhanced implementation reduced the mean absolute error from 10.476° to 1.054° and the internal command saturation ratio from 0.450 to 0.012 relative to the direct baseline, within the reported actuator, trajectory, and safety envelope. The main contribution was therefore not only a tuned controller but also a reproducible real-hardware methodology demonstrating how Nussbaum-based PID control could be successfully deployed and improved on a low-cost manipulator when adaptation management, actuation mapping, and hardware-aware optimization were treated as integral elements of the research design.
- 4 June 2026
- Published by MDPI AG in Preprints.org
Open AccessReal-Hardware Deployment of a Nussbaum-Function PID Controller on a Current-Controlled Low-Cost Actuator via Hardware-Aware Optuna Tuning
Real-hardware deployment of adaptive manipulator controllers remained difficult because assumptions made in paper-level formulations were often weakened by friction, encoder quantization, current limits, communication latency, and low-speed actuation nonlinearities. This paper investigated that deployment gap for a recent Nussbaum-function PID controller by translating it from a simulation-level formulation into direct current-command control on a Niryo NED3 Pro actuator. To isolate deployment-layer behaviour from whole-arm Coriolis, centrifugal, and gravity dynamics, the study focused on a single decoupled actuator (Dynamixel ID 6, distal wrist) under long-horizon sinusoidal tracking around a fixed operating region.A direct transfer of the baseline control law was first reproduced and was shown to degrade due to cumulative adaptation-state growth, weakening of the Nussbaum modulation, and high internal command saturation. A hardware-oriented implementation was then evaluated that preserved the Nussbaum core while introducing adaptation-state regularization, low-speed velocity-reference feedforward, and tail-region damping. Its parameters were selected through a hardware-aware Optuna optimization archive comprising 79 real-hardware trials, with unsafe runs rejected and a composite score reflecting tracking quality, internal command saturation, actuation activity, and bounded adaptation growth.Over 300 s of continuous operation, the enhanced implementation reduced the mean absolute error from 10.476° to 1.054° and the internal command saturation ratio from 0.450 to 0.012 relative to the direct baseline, within the reported actuator, trajectory, and safety envelope. The main contribution was therefore not only a tuned controller but also a reproducible real-hardware methodology demonstrating how Nussbaum-based PID control could be successfully deployed and improved on a low-cost manipulator when adaptation management, actuation mapping, and hardware-aware optimization were treated as integral elements of the research design.