Binod Barai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Binod Barai has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Abhigyan Ojha
School of Minerals, Metallurgical and Materials Engineering, Indian Institute of Technology (IIT) Bhubaneswar, Argul Campus, Bhubaneswar, India
1 shared publication - Abhishek Mandal
Department of Mechanical Engineering, Jadavpur University, Kolkata, India
1 shared publication Athmadeep Lala
Jadavpur University
1 shared publication- Biplab Baran Mandal
Department of Mechanical Engineering, Jadavpur University, Kolkata, India
1 shared publication - Buddhadeb Oraon
Department of Mechanical Engineering, Jadavpur University, Kolkata 700032, West Bengal, India
1 shared publication Buddhadeb Oroan
Jadavpur University
1 shared publication
Latest Publications
- 21 July 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (29) , 295001
Synergistic alloying and nanoparticle reinforcement in electroless Ni–Cu–P–TiO 2 coatings: a Taguchi-grey relational optimization approach
Electroless composite coatings were deposited on API X60 grade pipeline steel, and the effect of nickel sulfate, sodium hypophosphite, copper sulfate, and TiO 2 nanoparticle concentration on deposition rate, microhardness, and surface roughness was investigated using a Taguchi L27 experimental design coupled with grey relational analysis (GRA). Analysis of Variance (ANOVA) was used to determine the statistical significance of the process parameters. The optimized coating was subjected to post-deposition annealing at 200°C, 400°C, and 600 °C. Microhardness measurements, surface roughness analysis, field-emission scanning electron microscopy coupled with energy-dispersive spectroscopy, and x-ray diffraction were utilized to evaluate the coating characteristics. Sodium hypophosphite (P) and nickel sulfate (Ni) are identified as the dominant factors affecting microhardness (49.31% (P) and 38.78% (Ni)) and deposition rate (28.95% and 61.11%). In comparison, surface roughness is influenced by sodium hypophosphite (35.10%) and copper sulfate (Cu) (27.57%), as observed in the S/N ratio and ANOVA analysis. GRA optimum bath composition is 20 g l −1 nickel sulfate, 14 g l −1 sodium hypophosphite, 0.3 g l −1 copper sulfate, and 1 g l −1 TiO 2 . An experiment conducted under GRA-optimized conditions yielded a microhardness of 599 HV 0.05 , a surface roughness of 0.320 µ m, and a deposition rate of 13.08 mg.cm −2 .h −1 . Microstructural and phase analyses revealed a nodular, amorphous as-deposited coatings, while annealing promoted crystallization through the precipitation of Ni 3 P phase. The maximum hardness was obtained after heat treatment at 400 °C, whereas further increasing the annealing temperature to 600 °C resulted in a decrease in hardness and an increase in surface roughness, which was associated with microstructural changes and increased surface oxidation.
- 21 July 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (29) , 295001
Synergistic alloying and nanoparticle reinforcement in electroless Ni–Cu–P–TiO 2 coatings: a Taguchi-grey relational optimization approach
Electroless composite coatings were deposited on API X60 grade pipeline steel, and the effect of nickel sulfate, sodium hypophosphite, copper sulfate, and TiO 2 nanoparticle concentration on deposition rate, microhardness, and surface roughness was investigated using a Taguchi L27 experimental design coupled with grey relational analysis (GRA). Analysis of Variance (ANOVA) was used to determine the statistical significance of the process parameters. The optimized coating was subjected to post-deposition annealing at 200°C, 400°C, and 600 °C. Microhardness measurements, surface roughness analysis, field-emission scanning electron microscopy coupled with energy-dispersive spectroscopy, and x-ray diffraction were utilized to evaluate the coating characteristics. Sodium hypophosphite (P) and nickel sulfate (Ni) are identified as the dominant factors affecting microhardness (49.31% (P) and 38.78% (Ni)) and deposition rate (28.95% and 61.11%). In comparison, surface roughness is influenced by sodium hypophosphite (35.10%) and copper sulfate (Cu) (27.57%), as observed in the S/N ratio and ANOVA analysis. GRA optimum bath composition is 20 g l −1 nickel sulfate, 14 g l −1 sodium hypophosphite, 0.3 g l −1 copper sulfate, and 1 g l −1 TiO 2 . An experiment conducted under GRA-optimized conditions yielded a microhardness of 599 HV 0.05 , a surface roughness of 0.320 µ m, and a deposition rate of 13.08 mg.cm −2 .h −1 . Microstructural and phase analyses revealed a nodular, amorphous as-deposited coatings, while annealing promoted crystallization through the precipitation of Ni 3 P phase. The maximum hardness was obtained after heat treatment at 400 °C, whereas further increasing the annealing temperature to 600 °C resulted in a decrease in hardness and an increase in surface roughness, which was associated with microstructural changes and increased surface oxidation.
- 5 June 2026
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
ENHANCING CORROSION RESISTANCE OF BIODEGRADABLE MAGNESIUM ALLOYS THROUGH HYDROPHOBIC SURFACE MODIFICATION: EXPERIMENTAL ANALYSIS AND ANN MODELING
Magnesium alloys have garnered considerable attention as lightweight structural materials for diverse applications. However, their vulnerability to corrosion has constrained their widespread adoption. In this study, we introduce an innovative approach to significantly enhance the corrosion resistance of magnesium alloys by combining a hydrophobic coating with an artificial neural network (ANN) simulation. We successfully applied a stearic acid coating, boasting a water contact angle (WCA) of 130 ∘ , to a magnesium alloy substrate. The coated samples underwent thorough characterization using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX) to evaluate their microstructure and composition. Subsequently, the corrosion resistance of the coated samples was evaluated by immersing them in a simulated body fluid (SBF) solution, followed by a potentiodynamic polarization test. Initial experimental measurements indicated corrosion rates (CRs) ranging from approximately 4–9[ ]mm/year across various parameter combinations. To further enhance our predictive capabilities, we conducted data augmentation, significantly expanding the dataset for training the ANN model. This enhanced model demonstrated a remarkable prediction accuracy of over 98%, with an impressive correlation coefficient ([ ]) of 0.9844, firmly establishing its efficacy. Moreover, to ensure the robustness of the coated surfaces, we subjected them to a validation test at a coating temperature of 90 ∘ C for 4[ ]h. This led to the development of a superhydrophobic surface with a remarkable WCA of 151 ∘ , further enhancing the material’s resistance to environmental factors. In summary, our findings underscore the immense potential of coated magnesium alloys across a range of applications, including their use as biodegradable implants. The synergy between hydrophobic coatings and advanced ANN models has significantly improved corrosion resistance and surface properties, reinforcing the promise of magnesium alloys in numerous practical scenarios.
- 5 June 2026
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
ENHANCING CORROSION RESISTANCE OF BIODEGRADABLE MAGNESIUM ALLOYS THROUGH HYDROPHOBIC SURFACE MODIFICATION: EXPERIMENTAL ANALYSIS AND ANN MODELING
Magnesium alloys have garnered considerable attention as lightweight structural materials for diverse applications. However, their vulnerability to corrosion has constrained their widespread adoption. In this study, we introduce an innovative approach to significantly enhance the corrosion resistance of magnesium alloys by combining a hydrophobic coating with an artificial neural network (ANN) simulation. We successfully applied a stearic acid coating, boasting a water contact angle (WCA) of 130 ∘ , to a magnesium alloy substrate. The coated samples underwent thorough characterization using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX) to evaluate their microstructure and composition. Subsequently, the corrosion resistance of the coated samples was evaluated by immersing them in a simulated body fluid (SBF) solution, followed by a potentiodynamic polarization test. Initial experimental measurements indicated corrosion rates (CRs) ranging from approximately 4–9[ ]mm/year across various parameter combinations. To further enhance our predictive capabilities, we conducted data augmentation, significantly expanding the dataset for training the ANN model. This enhanced model demonstrated a remarkable prediction accuracy of over 98%, with an impressive correlation coefficient ([ ]) of 0.9844, firmly establishing its efficacy. Moreover, to ensure the robustness of the coated surfaces, we subjected them to a validation test at a coating temperature of 90 ∘ C for 4[ ]h. This led to the development of a superhydrophobic surface with a remarkable WCA of 151 ∘ , further enhancing the material’s resistance to environmental factors. In summary, our findings underscore the immense potential of coated magnesium alloys across a range of applications, including their use as biodegradable implants. The synergy between hydrophobic coatings and advanced ANN models has significantly improved corrosion resistance and surface properties, reinforcing the promise of magnesium alloys in numerous practical scenarios.